Problem Statement: You design a circuit of a decade counter that will count from 0-9 only. You will only be using the following: (a) Button – only 1 button will be used to trigger the counting. (b) Flip flop IC to used as counting circuit with 4 - BITS binary OUTPUT. (c) ICs for Decoding the Binary OUTPUT of Flip-flops to Decimal Output (d) 7- Segment Display to display the OUTPUT from 0-9. Block Diagram: 4 Bit Binary Flip-Flop Circuits 7-Segment Display Button Decoder Circuits

Problem Statement: You design a circuit of a decade counter that will count from 0-9 only. You will only be using the following: (a) Button – only 1 button will be used to trigger the counting. (b) Flip flop IC to used as counting circuit with 4 - BITS binary OUTPUT. (c) ICs for Decoding the Binary OUTPUT of Flip-flops to Decimal Output (d) 7- Segment Display to display the OUTPUT from 0-9. Block Diagram: 4 Bit Binary Flip-Flop Circuits 7-Segment Display Button Decoder Circuits

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

A d. B Figure 1 3. Referring to the logic circuit in Figure 1, determine: a. The simplified Boolean expression. b. The output waveform. C H c. Due to fabrication errors, lines d and f were shorted to the supply voltage. What happens to the output of the circuit? d. Your hardware resources are limited to 2-input NOR gate only. Draw the gate schematic of the simplified Boolean expression in 3(a).
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
9. Analysis of Synchronous Counters, in the following figure, write the logic equation for each input of each flip-flop. Determine the next state for state 010,011,100,111 as Q2Q1Q0 sequence. FF0 FFI FF2 Ko K, K2 CLK
1.) A storage register made up of six D flip-flops is storing a binary word. The flip-flop status are: A = set, B = set, C = reset, D = set, E = reset, and F = set. The A flip-flop is the LSB. The decimal equivalent of the register content is 2.) D flip-flops are most frequently used in
The logic diagram of JK flip-flop is given in Figure 3.a) Write the output Boolean functions for the outputs.b) Draw the timing diagram of the circuit on Figure 4. Assume that the delay between JK inputsand QQ outputs is 1 unit. Each column in Figure 4 represents 1 unit.
- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it
5- a- what are the application of Flip – Flop. b- What is the difference between the Flip – Flop circuit and the other combinational logic circuits?
(b) Analyse the sequential logic circuit for the D Flip-Flop shown in Figure below and answer the following sections Determine next state equations. Determine the state table for circuit in section (i). Draw the state machine diagram for D Flip-Flop of circuit in section (i). DD Figure (b)
Review Questions Question [4] For the given sequential circuit: a. What type of state machine is this circuit and why? b. Determine the flip-flop input equations and the output equations from the circuit. c. Derive the next-state equation for each flip-flop from its input equations. d. Derive the State table. e. Derive the State Graph. Determine the state sequence and output sequence if the initial state is So and the input sequence is X= 01100 B B KA CK JA KB CK to Clock Clock X" X- X' A B'
Design a three bit synchronous binary counter that counts two by two with T-flipflops,continously. Output should be one when the counter equals maximum number.a. Draw the exitation table b. Draw the corresponding state diagram. c. Tabulate the state table for the sequential circuit. d. Draw the logic diagram of the circuit.
Task 1: Custom Sequence Counter Using JK Flip Flop, Design a counter circuit that cycles through the sequence: 0, 5, 4, 6, 1, 7, and repeats. Follow these steps: a) State Diagram: Draw a state diagram representing the sequence. Each state should be expressed as a binary number. b) State Table: Create a state table for the counter, detailing current states, next states, and outputs. c) Flip-Flop Input Equations: From the state table, derive the input equations for the flip- flops. Treat any unused states as don't-care conditions. d) Simplification using K-maps: Use Karnaugh maps to simplify the flip-flop input equations. Optionally, verify your simplifications using Multisim. e) Circuit Diagram: Draw the circuit diagram. Task 2: 3-bit Up/Down Counter Using Flip Flop of your choice, design a 3-bit counter that counts up or down based on an input signal X. The counter should behave as follows: Initial State: On powerup, the counter starts at 0. Count Up (X=1): Sequence progresses through…
3. Referring to the logic circuit in Figure 1, determine: a. The simplified Boolean expression. b. The output waveform. A B H