Please only answer number 8 Problem 6. Ship's from Lat. 10°-46.8'N, Long. 105°-38.3'Eproceeding to Lat. 30 °-10.5'S, Long. 120°-12.2'E.What will be the difference of latitudeconverted to nautical miles.Solution:Problem 7. Ship's from initial position Lat. 48°-20.3'N, Long.175°-36.5'E to arrive in Lat. 51°-00.3’N,Long. 165°-00.8'W. Find the difference ofLongitude converted in nautical miles.Solution:Problem 8. From Nagoya, Japan to Los Angeles California,USA have a total distance of 7,653.8 nm and thevessel's speed was 15.25 knots. What will bethe voyage time?Solution:Problem 9. Calculate Dlo in degrees and Dlo in miles withdirection from Lat. 45-00.5’N, Long. 002°-48.5'Eto Lat. 12°-56.3'S, Long. 010°-59.3'E. What isthe difference of Longitude converted innautical miles.

Q 8. Given data d=7653.8 nmv=15.25 knots=7.93 m/sec Here, d is the distance and v is the speed of…

Answered: Problem 8. From Nagoya, Japan to Los…

Problem 8. From Nagoya, Japan to Los Angeles California, USA have a total distance of 7,653.8 nm and the vessel's speed was 15.25 knots. What will be the voyage time?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Figure 2 shows a horizontal beam AB. It is pin-supported at end A and carrying a load Q at end B.…

A: Introduction The column is the…

Q: A 5-kN tensile load is applied to a test coupon made from 1.6-mm flat steel plate (E = 200 GPa, v =…

Q: Consider a large plane wall of thickness L = 0.2 m, thermal conductivity k = 1.2 W/mK, and surface…

A: Given: L=0.2 mk=1.2 W/mKA=15 m2heat generation qg=500 W/m3at x=0, T=60oCTa=20oCh=200 W/m2K To find:…

Q: The materials for the members being joined in Probs. 9-1 to 9-4 are specified below, What 9-12 load…

Q: Completely solve and box the final answers. Write legibly Two moles of gas (O2) initially kept in a…

Q: R-134a at temperature = -10°C has a mass = 21 kg and a volume = 880L. The quality of the refrigerant…

A: Given:Temperature of R134a, T=-10°CMass of the refrigerant, m=21 kgVolume of the refrigerant, V=880L…

Q: raugue ng easures that may be taken to increase the resistance to fatigue of metallic materials. Ple…

A: Introduction: When a material is subjected to cyclic stresses and strains at high-stress…

Q: - For the concurrent coplanar force system shown determine the force in the boom (FAS) and the…

Q: An oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is…

Q: A single drum drier, operating at atmospheric pressure, is being used to dry a wet slurry,…

Q: A particle moves along a path according to the equations x = 9 - +4/9 and y = +²/3 where x and y are…

Q: write vector loop equation(s) theta2=57 also if a new length is constructed find its value. 57° 30°…

Q: The Poisson's ratio of a linear elastic, isotropic material is 1/3 and its elasticity mass is 210…

A: Given data:- Poisson's ratio = 1/3 Youngs modulus = 210 Gpa Find the strain tensor.

Q: B. Derive the transfer function X, (s)/F(s) for the mechanical system shown in Assume the following…

Q: PROBLEM: One insulated rigid tank contains 1 kg of carbon dioxide CO2 at 3 bar and 150℃, while a…

Q: A piston–cylinder assembly contains 2 lb of water, initially at 100 lbf/in.2 and 400°F. The water…

Q: 4. How far from the earth must a body be along a line toward the sun so that the gravitational pull…

Q: A certain engine produces 10 kW indicated power. It's mechanical efficiency is 70%. Then the…

A: Given: Indicated power of the engine: →IP=10 KW And mechanical efficiency: →ηmech=70%=0.70

Q: Refrigerant 134a expands in a piston-cylinder assembly from p₁ = 160 lb/in² and T₁ = 140°F to p₂ =…

Q: Particles A and B are traveling counter-clockwise around a circular track at a constant speed of 8…

A: Given-Information:- v = 8m/satA = 0.8sA m/s2r = 6 m To-Determine:- 1. Distance measured…

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

A: Given Data- A plane truss given we have to find force in all member of given truss

Q: Find the greatest weight that can be applied without the front wheels lifting off the ground. The…

Q: The cycle for a heat engine consists of Compression from points 1 to 2. No heat flow but work done…

A: Given: process 1 to 2: It has compression and heat flow is zero. So→Q12=0 And work done on the gas…

Q: Two lbs of water vapor in a piston-cylinder assembly expands at a constant pressure of 200 lb/in²…

A: Given: Mass of the water vapor→m=2 lbs constant pressure of the water vapor: →P=200 lbf/in2 At this…

Q: Carbon dioxide (CO₂) fills a closed, rigid tank fitted with a paddle wheel, initially at 80°F, 50…

A: Given Data The pressure of the carbon dioxide is: P=50 lbf/in2=344738 Pa The temperature is:…

Q: Design the diameter of a steel pipe to carry water having kinematic viscosity v=10 m²/s with a mean…

Q: The figure above shows a schematic of a gas turbine engine. Engines such as these provide thrust to…

A: Given questions are related to machine design, material science and manufacturing engineering.

Q: Determine the force in member BD and state whether the member is in tension or compression. Iren 30°…

A: Given Force, F = 7.8 kN Angle = 30o Find Force in member BD, RBD

Q: 03: A: What is the effect of increasing the airfoil angle of attack on lift and flight? Briefly…

A: Given question is related to fluid mechanics

Q: A rigid, well-insulated tank contains a two-phase mixture of ammonia with 0.0019 ft3 of saturated…

Q: Grade 300 maraging steel is an alloy of iron, nickel, cobalt, molybdenum, titanium, aluminum, and…

A: Solution: Given Data: Maraging steel To Find: (a) Composition of the alloy. (b) Anodic and…

Q: Air flows through a horizontal pipe at the rate of 3,000 cu ft. per sec. If the pressure is 30 lb…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: For a bolted assembly, the stiffness of each bolt is kb members is km 12 Mlbf/in per bolt. The joint…

A: Given-Information:- kb = 4 M lbf/inkm = 12 Mlbf/inPmax = 80kipsPmin = 20kips12 in - 13 UNC grade 8…

Q: Make a graphical plot of ISO cleanliness classes 1 to 4 for particle sizes 0.1 to 1um

A: Given question: Make a graphical plot of ISO cleanliness classes 1 to 4 for particle sizes 0.1 to…

Q: Angular speed of Cranker 1 is ₁. For the given position in the following figure, (1) Find out all…

Q: The x-coordinate of a particle in curvilinear motion is given by x= 4.8t³-2.7t where x is in feet…

Q: Steam enters an adiabatic turbine steadily at 8 MPa, 500 °C, 50 m/s and exits at 30 kPa. 150 m/s.…

A: Introduction The second law…

Q: A turbocharged 6-cy, V-type diesel engine has an air consumption of 3000 kg/hr. per cylinder at…

Q: The compressed air has a volume of 0.84 ft³ The temperature is 70 °F and the atmospheric pressure is…

Q: Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB…

Q: Steam, initially at 700 lbf/in.2, 550°F undergoes a polytropic process in a piston-cylinder assembly…

Q: Air is compressed in a piston-cylinder assembly from p₁ = 15 lbf/in², T₁ = 500°R, V₁ = 9 ft³ to a…

A: Given data :- P1 = 15 lb/in^2 , T1 = 500°R , V1= 9 ft ^3 V2 = 1 ft ^ 3 Process pv^1.2 = constant…

Q: What is the internal shear force over the cross section at point C? 8 kN/m A -4 m-C 8 m 10m B T2 KN

Q: Locate all the insta of the mechanism

A: Given-Information:- AB = 150 mmBC = 300 mmCD = 225 mm CE = 500 mm NAB =240 rpm To-Determine:- 1.…

Q: The figure shows a weldment just like that for Probs. 9-17 to 9-20 except there are four welds…

A: Given data as per the question No. of weld of the object =4

Q: What is the internal shear force over the cross section at point C? 8 kN/m -30 kN ☐-6 kN 30 kN -62…

Q: A helical compression spring is to be made of oil-tempered wire of 4-mm diameter with a index of C 5…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: It is observed that the skier leaves the ramp A at an angle A = 22° with the horizontal. (Figure 1)…

A: Given Data The angle at A is: θA=22° The distance of B is: B=100 m The height of A is: A=4 m The…

Q: A piston-cylinder assembly contains 0.5 lb of propane. The propane expands from an initial state…

A: Given Data The mass of the propane is: m=0.5 lb The initial pressure is: p1=60 lbf/in2=8640 lbf/ft2…

Q: The artery inner and outer diameters are 15mm and 20mm, respectively. The blood pressure is 100mmHg.…

A: Given: R1 = 15 mm R2 = 20 mm P = 100 mmHg = 13300 Pa To find: Hoop stress. Radial stress

Question

Please only answer number 8

Problem 6. Ship's from Lat. 10°-46.8'N, Long. 105°-38.3'E
proceeding to Lat. 30 °-10.5'S, Long. 120°-12.2'E.
What will be the difference of latitude
converted to nautical miles.
Solution:
Problem 7. Ship's from initial position Lat. 48°-20.3'N, Long.
175°-36.5'E to arrive in Lat. 51°-00.3’N,
Long. 165°-00.8'W. Find the difference of
Longitude converted in nautical miles.
Solution:
Problem 8. From Nagoya, Japan to Los Angeles California,
USA have a total distance of 7,653.8 nm and the
vessel's speed was 15.25 knots. What will be
the voyage time?
Solution:
Problem 9. Calculate Dlo in degrees and Dlo in miles with
direction from Lat. 45-00.5’N, Long. 002°-48.5'E
to Lat. 12°-56.3'S, Long. 010°-59.3'E. What is
the difference of Longitude converted in
nautical miles.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Give this answer only but instant soln plz. Plz provide correct
Solve the followig and show complete solution
Exercise 1 Tabulate the absolute coordinates. Write a program to drill the holes and mill the rectangular pocket. Exercise 2 20 30 60 80 4x02 x 5 deep 2 Material: Square Pocket: 5mm deep Tool change at: XO, YO, Z 25 15mm thick Plastic 3 plno
Show the steb by step solution
show the FBD and complete solution
Fluid Force. A swimming pool is filled with fresh water to a depth of 7 feet measured at the deep end. There is not enough water in the pool to reach the shallow end. Assume that the pool is constucted using right angles, except where the bottom of the pool meets the end walls. Use Ah for the height of a typical strip across the face of the wall. 6. The weight density of water is 62.4 lb/ Your anwers should have units: pounds. 4 ft 18 ft 24 ft Declare your variable(s) here. Show your reasoning below: a) find the force on the typical horizontal strip (red) ? b) write an integral for the total force on the (left) wall of the pool
draw an fbd and show the complete solution
resolve both and show all steps and solution
Dynamic question Solve this question by using a triangle of speeds method Send the answer quickly please
two pulleys are connected by a belt. The nubers of RPM of the two pulleys vary inversely as their diameters. A pulley having a diameter of 25cm is turning at 900 rpm. what is the number of RPM of the second pulley wgich has a diameter of 40cm
Problem 77 please make the calculation easy to understand
View Image. Show complete and detailed solution. Please write legibly. Answer: 64.3 degrees