Please show all of your work and do the calculations for the problem in the picture Problem 12Knowing that P = 5.2 kN, determine the factor of safety for the structure shown.Use E = 200 GPa and consider only buckling in the plane of the structure.F.S. = 1.5P70%B22-mm diameter1.2 m18-mmdiameter1.2 m

Answered: Image /qna-images/answer/ae2daf23-06b4-48c6-a212-66a03425c338.jpg

Answered: Problem 12 Knowing that P = 5.2 kN,…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A vibration isolation support consists of a rod A of radius R₁ and a tube B of inner radius R₂ bonded to an 80-mm-long hollow rubber cylinder with a modulus of rigidity G = 10.93 MPa. Determine the required value of the ratio R2/R1 if a force P = 13 kN is to cause a 2-mm deformation of rod A. B R₁ R₂ .. 80 mm The required value of the ratio R2/R₁ is 1.422
An E-Shape beam with the cross-section is bent about vertical axis. As shown in Figure Q3, N-N is plastic neutral axis Assume that the yield stress, oy is 275 MPa and the elastic bending moment, My is 18.88 kNm, (i) determine the plastic moment, M, of the beam. (ii) determine the value of the shape factor for the beam. N 20 тm | 20 тm 100 тm 20 тm 60 тm 20 тm 80 тm N Figure Q3
A 3mm thick hollow polystyrene cylinder (E = 3 GPa) and a rigid circular plate (only part of which is shown in Figure 2) are used to support a 6mm diameter steel rod AB (E = 200 GPa) of length 250mm against a rigid baseplate. If a 3.2 kN load P is applied at B, determine the following: - (a) the elongation of rod AB. (b) the deflection at point B. (c) the average normal stress in rod AB. 30 mm 250 mm A 6 mm P= 3.2 kN 50 mm Circular plate Polystyrene cylinder Baseplate
Current Attempt in Progress The uniform beam has a mass of 47 kg per meter of length. Determine the reactions at the supports. 2.7 m 1.2 m 200 kg A B Answers: Ay = Bx= eTextbook and Media z z z
Mechanics of Deformable Bodies Determine the maximum tensile and compressive bending stresses in the beam shown. 4 kN/m 200 mm putium, El A B 6 m 80 mm † 1= 30 x 106 mm ΝΑ
2.4 The truss shown is the same as in Example 2.1 except that the area of bar ab is a variable. E = 200,000 MPa. (a) For what value of Aah is v. = 0? Is this a function of the magnitude of the applied load? (b) Is it possible to obtain zero u, by varying A? (c) Suppose the applied load were vertical rather than horizontal, would it then be possible to obtain zero u, by varying Aab? If so, for what value of Aab? What would be the corresponding v.? 500 kN Fah = +400.6 kN Aab 4 m 6 m 3 m Problem 2.4 Fac = -277.8 kN Aae = 8000 mm?
The rigid bar BDE is supported by two links AB and CD. Link AB is made of steel (E=200 GPa) and has a cross sectionnal area of 700 mm; link CD is made of aluminum (E=70 GPa) and has a cross sectional area of 500 mm. For the 28 kN force shown, deflection at E. 0.4 m 0.3 m 28 kN B 0.25 m 0.60 m
The steel plate shown below is put in into a rigid chamber, such that spacings of size s = 0.003 m. To fit the plate, it is heated. It can be assumed that the plate can move frictionless along its edges. If x = 4 m and y = 2 m, E = 200 GPa !! V = 0.28 = 11.7 x 10 FC Which temperature increase along the x-axis is required to just close the spacing on the right in degree celcius? Select the correct response 85.470 O 64.103 040.171 32.051
2.25. A system consists of two rigid end-plates, tied together by three horizontal bars as shown in Fig. 2-42. Through a fabrication error, the central bar, ②2, is 0.0005L too short. All bars are of identical cross section and of steel having E = 210 GPa. Find the stress in each bar after the system has mechanically been pulled together so that the gap A is closed. Ans σ-35 MPa σ = 70 MPa Fig. 2-42
Question #4: Determine the state of stress at point A on the cross section of the beam at section a-a. Show the results in a differential element at the point. O 2. T a 0.5m 0.5m 30 kN 2 m 100mm 50mm I 10mm 10mm 180mm Section a-a 10mm
A solid circular steel shaft of 50 mm diameter, fixed at one end, is subjected to torques as shown below. The shearing modulus of the material is 80 GPa. 500 Nm 250 Nm 500 mm 500 mm 500 mm The rotation of the free end S due to torsion is
1. Given that the value of P on the figure below is equal to 15 kN which is applied to the centroidal axis of each segment of the rod which is made up of aluminum, bronze and steel which are rigidly connected. Determine the stress in each material in the rod. Steel A=300 mm2 Bronze Aluminum A=400 mm2 A=600 mm2 2P ЗР 4P P 3m+ 5 m 4 m-

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Problem 12 Knowing that P = 5.2 kN, determine the factor of safety for the structure shown. Use E = 200 GPa and consider only buckling in the plane of the structure. F.S. = 1.5 P 70% B 22-mm diameter 1.2 m 18-mm diameter 1.2 m