Problem #1 (Pipes Iterative Analysis): Water at 70°F flows through 100 feet of pipe 10 inches in diameter with an equivalent roughness E of 0.00085 ft. A head loss of 0.5 feet is measured over this length of pipe, find the flow rate. Use any method, show at least two iterations, neglect minor losses. (v = 1.05 x 10-5ft2/s) (14/100) h= 0.5 ft Total System Head. E=0.00085 ft 100

Problem #1 (Pipes Iterative Analysis): Water at 70°F flows through 100 feet of pipe 10 inches in diameter with an equivalent roughness E of 0.00085 ft. A head loss of 0.5 feet is measured over this length of pipe, find the flow rate. Use any method, show at least two iterations, neglect minor losses. (v = 1.05 x 10-5ft2/s) (14/100) h= 0.5 ft Total System Head. E=0.00085 ft 100

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3.2. A water (Temperature = 20 °C) is flowing in a commercial steel pipe at a flowrate of 5 m³/s. The diameter and length of the pipes are 50 cm and 500 m, respectively. Assume absolute roughness (ɛ) = 0.05 mm. Calculate the head loss by using: (a) Darcy-Weisbach equation (b) Manning's equation (use n = 0.017)
Compute the discharges for the pipes of the network shown below. Use the Hardy Cross method. Only one iteration cycle is required. The Hazen-Williams coefficient is 130 for all pipes. Begin your computation with the assumed discharges given below and verify that they satisfy the continuity requirement. QAB = 2.4 cfs (from A to B) QBD = 1.5 cfs (from B to D) QBC = 0.3 cfs (from B to C) QCD = 0.5 cfs (from C to D) QAC = 1.8 cfs (from A to C)
A 300mm diameter pipe has a flow rate of 200 L/s. Assuming the length of the pipe is 300mm, determine a) friction factor, b) roughness coefficient, and c) Hazen Williams Coefficient (A No answer among the choices in question B (В) с - 93.43 No answer among the choices in question A (D) n = 0.0243 (E) f = 0.0218 (F) c = 87.96 G) c = 107.57 (H) f = 0.0245 ) f= 0.0236 ) f= 0.0257 (K) n = 0.0115 L No answer among the choices in question C (M) n 0.0412 (N) C = 101.09 n = 0.0348
Water flows from reservoir A to B through the three concrete pipes shown below. Assume that concrete has f=0.023. Neglect all minor losses. 2500 m 400 mm Ø 20 m and Dnew 1850 m 300 mm Ø 800 m 200 mm g a) Determine the flow rate from A to B in m³/s b) Determine the diameter (mm) of an equivalent pipe made out of steel with f=0.012.
absolute roughness is o.03mm (for both sections), Determine the height H. Neglect local losses. Tip: Losses in pipes connected one after another (as in the figure) they add up 2. Consider the system shown. If the flow is Q = 220 lts / s and the H L=500 m D=45 cm L=800 m D=30 cm
Question: In the water network shown in figure,the Hazen-Williams coefficient C for all pipes is 100. a) Using the Hardy Cross method, determine the flow in each pipe to the nearest 20 gprn. b) Find the residual pressures at points B and C, given that the pressure at point Aee is 50 psi. C) If the flow input A is doubled,what would be the residual pressure at C? Elevation 1,600 gpm A A 100 ft B 150 ft C 140 ft 1,500 ft 8 in 500 ft 10 in B 1,000 ft 10 in 1,000 gpm 600 gpm
The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the tank is 0.028 m^3/ sec. Determine the minimum height, h, of the water tank under the assumption that (a) minor losses are negligible, (b) minor losses are not negligible. 3 m Figure No.3 Kentrance = 0.5 h The pipe is plastic of 15 cm diameter and (e/D=D0) 1.8 m (2) Main line 450 m with 15 elbows of 90 degree
Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section from point 1 to point 2, which is 1.5 m above point 1, at the rate of 0.9 m³/s. At section 1 the pipe dia is 0.5 m and pressure is 800 kpa. If pressure at section 2 is 600 kpa determine the pipe diameter at that location. (neglect the losses) tt thele loloses)
Add the energy grade line (EGL) as a solid line and the hydraulic grade line (HGL) as a dashed line to the figure below. Enter the corresponding numbers in the table. Assume steady incompressible flow from left to right. At point A, the pressure head P/y = 23 ft and the velocity is V=8 ft/s. The pump adds AH = 16 ft. Ply V²/(2g) EGL HGL EGL and HGL [ft] >> EGL_HGL(2,1,2,'-','P',20,'ft') A D, 2 ft B C D₂ = 1 ft D E D₂ = 2ft F 30 T TI 25 20 5 10 0 5 A A 10 B F 15 20 x [1000 ft] C 25 D 30 E F
1. The figure shows a looping water pipe system. The pressure drop stood at200030> mmHg from point A to point B. Assume f = 0.053 all pipes. PIPE 1 Qu PIPE2 A B PIPE 3 Length, m 2500 > Pipe Diameter, mm 1 400 300 3 200 a. Compute the discharge at pipe 1 b. Compute the discharge at point A c. Compute the diameter of the equivalent pipe of the same material with a length of 1500m
Q2) i Neglecting minor losses in the pipe, determine the flows in the pipes and 0 the pressure heads at the nodes (kinematic viscosity= 1.13x104m?¥s) F E n I I 30 Data Pipe Ab BC O DE EF AF BE Lengeh (m) 600 600 200 600 600 200 200 Diameter (wm) 250 150 100 150 150 200 100 Roughness size of all pipes = 0.06 mm Pressure head elevation at A = 70 i o.d. Elevation of pipe nodes A 5 c D L ® 028 0 20 2 2
Orifice meter with orifis cross-section 0.00785 m2 is inserted in a pipe of cross-section 0.0314 m2. The pressure gauge fitted upstream and downstream of orifice give reading of 19.62 N/cm2 and 9.81 N/cm2 respectively. Determine the value of dischareg using Cd=0.6.