Prob. # 5] A steel rod of 25 mm diameter is fitted inside a brass tube of 25 mm internal diameter and 375 mm external diameter. The projecting ends of the steel rod are provided with nuts and washers. The nuts are tightened up so as to produce a pull of 5 kN in the rod. The compound is then placed in a lathe and the brass is turned down to 4 mm thickness. Calculate the stresses in the two materials.

Prob. # 5] A steel rod of 25 mm diameter is fitted inside a brass tube of 25 mm internal diameter and 375 mm external diameter. The projecting ends of the steel rod are provided with nuts and washers. The nuts are tightened up so as to produce a pull of 5 kN in the rod. The compound is then placed in a lathe and the brass is turned down to 4 mm thickness. Calculate the stresses in the two materials.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.25P: A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just...

See similar textbooks

Similar questions

Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
The figure shows 16-mm diameter bolts used to hold two steel plates by fitting inside a cylindrical spacers. Thenormal stress must not to exceed 230 MPa in the bolts and 160 MPa in the spacer. Determine the outer diameterof the spacer.
An aluminum alloy cylindrical roller with diameter 1.25 in and length 2 in rolls on the inside of a cast-iron ring having an inside radius of 6 in, which is 2 in thick. Find the maximum contact force F that can be used if the shear stress is not to exceed 4000 psi.
3. Calculate the contact stress between a 100-mm- diameter steel ball weighing 500 g sitting on a hardened steel surface plate.
A cylindrical pressure vessel is designed using steel plating with a thickness equivalent to 15 mm. The inside diameter is 460 mm and its height is 2.5-m. Solve for the maximum internal pressure that can be implied if the longitudinal stress is only up to 120 MPa, while the tangential stress is only up to 50 MPa.
The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
A flanged bolt coupling consists of eight 10-mm diameter steel bolts on a bolt circle 400 mm in diamater and six 10 mm diamter steel bolts on a concentric circle 300 mm in diameter. When the shear force developed in each bolt in the outer concentric circle is 8000 N, then the stress in each bolt is
The vertical load P acting on the wheel of a traveling crane is 13,000 lb. What is the average shear stress in the 1.25 in. diameter axle?
Assume that the axial load P applied to the lap joint is distributed equally among the three 20-mm-diameter rivets. What is the maximum load P that can be applied if the allowable stresses are 40 MPa for shear in rivets, 90 MPa for bearing between a plate and a rivet, and 120 MPa for tension in the plates?
A simplified model of a basketball hoop is shown. During a basket dunk a player hangs from the rim applying a force of 320 lbs including a dynamic load factor. The stand is a square tube with 5 inches outside length and 0.25 inches thickness. The distance from the edge of the rim to the middle of the square tube is 4 ft. Assuming the model is rigid, the normal stress at point A is most closely equal to: a. 1284 psi b. 1248 psi c. 1212 psi d. 36 psi A
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: 0,05 and Txs 72.2 144.4 144.4 MPa A,B A,B A,B a. Determine Gmin, Omax, and its direction (in degrees) from x-axis at point A. b. Determine Omin, Omax, and its direction (in degrees) from x-axis at point B. B S A " O X