Please consider the following segment of an assembly language program. Manually execute one instruction at a time and write the new resulting contents of conditions codes N/Z/V/C, Registers R5/R6, and any possible new Memory Contents. Write the contents without any prefix or suffix, just the hex contents. mov.w #0x9599, R5 NZVC Instruction 0110 0x1234 mov.w #Ox0206, |--CC- R6 mov.b R5, O(R6) R5 R6 OxA006 Memory Memory Address Contents Ox0200 Ox5800 Ox0202 0x5700 Ox0204 0x5600 New Contents Ox0206 Ox5500 1

Please consider the following segment of an assembly language program. Manually execute one instruction at a time and write the new resulting contents of conditions codes N/Z/V/C, Registers R5/R6, and any possible new Memory Contents. Write the contents without any prefix or suffix, just the hex contents. mov.w #0x9599, R5 NZVC Instruction 0110 0x1234 mov.w #Ox0206, |--CC- R6 mov.b R5, O(R6) R5 R6 OxA006 Memory Memory Address Contents Ox0200 Ox5800 Ox0202 0x5700 Ox0204 0x5600 New Contents Ox0206 Ox5500 1

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

1- Write a program in assembly language to perform the following logic ci D- CL DL [5100]– 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL, 00 MOV BX, FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX, 就

1- Write a program in assembly language to perform the following logic ci CL DL [5100]– 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX, FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX,
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Question 1: Use Indirect addressing to write a PIC24 assembly code that complements and adds 5 and multiply by 2 to 1024 data bytes into the memory at starting address Ox1000. The original data are stored in the memory starting from address 0x800. it is an electrical engineering question . this is the full information about the question!
After executing XLAT instruction, the content of system registers is: ES=4E25, DS=041C DI=6814, BX=0201, and AL =40, (all values shown are in hexadecimal and the addresses shown are physical addresses). What is the content of AL before executing this instruction? H. H. Address 20н 40 H 60 н 80 H A0H СОн E0 H Content 447C 447D 447E 447F 4480 4481 4482 Notes: 1- Use the memory fragment shown to answer this question. 2- Write down the final value of AL as two hexadecimal digits without any additional characters.
An 8085 assembly language program is given below. Line 1: MVI A, B5H 2: MVI B, OEH 3: XRI 69H 4: ADD B 5: ANI 9BH 6: CPI 9FH 7: STA 3010H 8: HLT The contents of the accumulator just execution of the ADD instruction in line 4 will be
ehcu.org/pluginfile. هل ترید اس لم يقم إيقاف + 100% 10 / 11 Questions:- 1- Write a program in assembly language to perform the following logic ci CI DL [5100]. 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX , FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX , 161756649_26189.jpg O 12.jpg LG
Discuss in detail about RAM allocation in 8051 and Analyse, and explain the objective of the following 8051 assembly language program. Specify the content of the Program Status Word (PSW) register after the execution of each instruction. ORG 00H MOV A#00H MOV R5,A MOV R0,#0FBH ADD A#0FEH JNC NI INC R5 N1: ADD A, #0F5H JNC N2 INC R5 N2: ADD A#0F2H INC OVER INC R5 OVER: MOV @R0, A END Comment every line of the program and specify the register contents on single-step execution.
An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 M
You are given the following assembly language statements: MOV AX, 15225 MOV BL, 126 DIV BL SUB BL, AL Just after the CPU finishes executing the SUB instruction, calculate the following: i)The decimal values in AL, AH, and AX registers ii)The decimal value of BL iii)The values of flag bits: Sign, Carry, Auxiliary, Zero, Parity, and Overflow.
Question 1: Consider the following assembly language program. Determine the internal memory location after every MOV instruction in the program. RETMON EQU OF000H ORG 100H START MOV R5,#25H SETB PSW.4 MOV R6,#67H SETB PSW.3 MOV R4,#36H CLR PSW.4 MOV R7, #89H LCALL RETMON END
This question is from the subject Digital Logic Design. Assume your register number SF20-BEC-xxx (excluding the dashes -) is in Hexadecimal, where xxx are the three digits of your registration number. a) Represent your registration number in the binary.b) Split the ten digits of your registration into two Hexadecimal numbers M and N, where the left most five digits make number M and the right most five digits make number N. Using r’s complement, subtract N from M. In other words, calculate M – N. Solve the question for registration no SF20-BEC-156.