Part A If P = 4 kN, determine the slope at A of the simply supported beam. The modulus of elasticity of the wood is E = 10 GPa (Figure 1 Express your answer with the appropriate units. HÀ ? Value Units Submit Request Answer Figure 1 of 1> Part B Determine the deflection at point C of the simply supported beam. Express your answer with the appropriate units. 100 mm Fomm Ac = Value Units Submit Request Answer

Part A If P = 4 kN, determine the slope at A of the simply supported beam. The modulus of elasticity of the wood is E = 10 GPa (Figure 1 Express your answer with the appropriate units. HÀ ? Value Units Submit Request Answer Figure 1 of 1> Part B Determine the deflection at point C of the simply supported beam. Express your answer with the appropriate units. 100 mm Fomm Ac = Value Units Submit Request Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Suppose that in addition to the 2.00-kN downward force acting at point D, a 2.20-kN downward force acts at point C. ( Figure 1) Figure 3 m 3 m B -5 m- 44°F Mostly clear -5 m- D 1 of 1 2 kN Ex Search Pa De Ex Provide
A plank of wood is to be tested for its compressive strength, the cross-section of the timber is 200mmX200mm and 500mm tall. The result of the test gave 408KN before breaking. given E=9.72GPa Determine the maximum compressive stress taken by the wood a. 10.20MPA O b. 10.20Pa O c. 0.0102MPA O d. 0.0102Pa 22. Determine the elongation of the wood before breaking a. 5.246mm b. 52.46mm c. 0.05246mm O d. 0.5246mm
(5) This simply-supported beam has been subjected to an applied moment at midspan. The M(x) equations have been supplied for you. You are to write the v(x) equations for 0
OOKN GOKN K B 75KN 75KN 75 KN G@ Am = 24 m %3D Determine the Miember force on member EJ.
Rod AB is made of a mild steel that is assumed to be elastoplastic with E = 200 GPa and oy =250MPA . After the rod has been attached to the rigid lever CD, it is found that end C is 6 mm too high. A vertical force Q is then applied at C until this point has moved to position C'. Determine the required magnitude of Q and the deflection ô, if the lever is to snap back to a horizontal position after Q is removed. 9-mm diameter 1.25 m 6 mm 0.7 m 0.4 m
(40 H.wA Rismatic steel bar of a Square cro ss section (lookloo)mm is locoled by compressive forcc P= 1300 k, the bar has length 2.5 m, =200 G Pa, V=0.3, determine the Shortening S, the Incrense in the dimensions of cross Section, the change In Volume DV of the bar? 7. loomm loomm
For the wooden beam sketched in the figure, ask for the mid-span section. a) Determine the normal stresses at points 1, 2, 3 and 4. (Represent the distribution of normal stresses in the section) b) Check the structural safety in relation to normal stresses. (Adopting γt = 3.2 and γc = 2.5) ADDITIONAL DATA / INFORMATION Characteristic strengths of wood: TENSION: σr,t = 52 MPa COMPRESSION: σr,c = 40 MPa
Question 2. AP A 1 0.4m 0,5m d=20mm d= 60mm Both partion of rod ABC are made of an aluminum for which E= 704Ppa. Knowing that the magnitude of P is 4 KM, Determine; (a) the volue of Q so that the deflection at A is zero. 8. (b) the corresponding deflection of
FOR THE GIVEN PROPERTIES DESIGN d': 15 mm THE REINFORCEMENT OF : 400 mm b d = $80 mm fc = 33 MPa fy = 320 MPa Mu: 1 000 000 000 N mm A. USE B.USE OF NSCP 2001 NSCP 2015 BEAM THE BEAM 132 13 Gra mm of BELOW. #H 1606 210135 03 M 12437 P0122399/100mA 02338941 242
The two steel plates are bolted to the wooden beam shown by 30-mm-diameter bolts spaced at 200 mm. Knowing that beam is subjected to V 5000 N, and that the moduli of elasticity for steel and wood are 200 and 40 GPa, respectively. Determine: (a) Shearing stress in each bolt; and (b) shearing stress at the mid- height of the upper steel plate. 150 mm 12 mm 250 mm 12 mm Solution:-
... 150 mm F = 30N 150 mm water 3m When a 30N force is placed on the end of a floating 150mm x 150mm x 3m long wooden beam, the beam tilts by 2 degrees as shown. Determine the specific gravity of the wood. 0.606 0.794 0.716 D No answer among the choices E) 0.672
d C