net protocol, sender sends one character at a time. Explain how TCP would adopt in this scenario to accommodate the issues caused by the slow sender Draw a time-line diagram for sliding-window to show how receiver may obtain the duplicate frames. What condition is necessary to detect duplicate frames. Draw both scenarios i.e.in which duplicate frames are detected and not detected by the receiver

net protocol, sender sends one character at a time. Explain how TCP would adopt in this scenario to accommodate the issues caused by the slow sender Draw a time-line diagram for sliding-window to show how receiver may obtain the duplicate frames. What condition is necessary to detect duplicate frames. Draw both scenarios i.e.in which duplicate frames are detected and not detected by the receiver

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter9: Computer Networks

Section: Chapter Questions

Problem 10VE

See similar textbooks

Computer Science

In Telnet protocol, sender sends one character at a time. Explain how TCP would adopt in this scenario to accommodate the issues caused by the slow sender

Draw a time-line diagram for sliding-window to show how receiver may obtain the duplicate frames. What condition is necessary to detect duplicate frames. Draw both scenarios i.e.in which duplicate frames are detected and not detected by the receiver

How orphan frames are detected in the token-ring networks. Also explain how reliability is achieved in the token-ring network.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Question 5: Suppose you attach a network monitor to observe the sequence of frames that travel over a link from sender A to receiver B. The problem is to deduce what protocols, if any, could have generated the observed sequence. The following diagrams depict a flow of frames, with their corresponding sequence numbers, from the sender (A). There may be traffic from B to A, which is not depicted in the diagram. A gap between adjacent frames implies passage of time with no transmission from the sender. Note that the x-axis is time, and not space. Justify your answer. A A A ● ● ● ● 1 5 ● 3 5 0 ● 0 0 1 1 1 ● Go-Back-N ● Selective Repeat 1 0 5 0 c) For Diagram 3, the protocol is not: Stop-and-Wait Time Diagram 1 2 Time a) For Diagram 1, the most likely protocol being used is: Stop-and-Wait ● Go-Back-N (if Go-Back-N, give the window size) Selective Repeat (if Selective Repeat, give the window size) Diagram 2 Time 3 Diagram 3 1 Time b) For Diagram 2, the most likely protocol being used is:…
In protocol 6, the code for frame arrival has a section used for NAKs. This section is invoked if the incoming frame is a NAK and another condition is met. Give a scenario where the presence of this other condition is essential.
Consider the rdt 3.0 protocol. Draw a diagram showing that if the network connection between the sender and receiver can reorder messages (that is, that two messages propagating in the medium between the sender and receiver can be reordered), then the alternating-bit protocol will not work correctly (make sure you clearly identify the sense in which it will not work correctly). Your diagram should have the sender on the left and the receiver on the right, with the time axis running down the page, showing data (D) and acknowledgment (A) message exchange. Make sure you indicate the sequence number associated with any data or acknowledgment segment.
Explain the flow control of TCP protocol when the size of the sliding window will be 500 and the first client sends 201, 301, 402, 455, 330, and once acknowledgments will receive client will send 602. Make a flow control of these packets
TCP congestion control example. Consider the figure below, where a TCP sender sends 8 TCP segments at t = 1, 2, 3, 4, 5, 6, 7, 8. Suppose the initial value of the sequence number is 0 and every segment sent to the receiver each contains 100 bytes. The delay between the sender and receiver is 5 time units, and so the first segment arrives at the receiver at t = 6. The ACKS sent by the receiver at t = 6, 7, 8, 10, 11, 12 are shown. The TCP segments (if any) sent by the sender att = 11, 13, 15, 16, 17, 18 are not shown. The segment sent at t=4 is lost, as is the ACK segment sent at t=7. t=1 T data segment t=2+ data segment data segment-- t=3 TCP sender TCP receiver t=4+ t=5+ data segment - data segment t=6+ t36 data segment t=7 data segment t=8 data segment t=9 ACK + t=10 k -- ACK t=11 t=11 t=12 t=12 t=13 t=13 t=14 ACK -ACK ACK t=15 t=16 t=17 ACK t=18 What does the sender do at t=17? You can assume for this question that no timeouts have occurred.
TCP congestion control example. Consider the figure below, where a TCP sender sends 8 TCP segments at t = 1, 2, 3, 4, 5, 6, 7, 8. Suppose the initial value of the sequence number is 0 and every segment sent to the receiver each contains 100 bytes. The delay between the sender and receiver is 5 time units, and so the first segment arrives at the receiver at t = 6. The ACKs sent by the receiver at t = 6, 7, 8, 10, 11, 12 are shown. The TCP segments (if any) sent by the sender at t = 11, 13, 15, 16, 17, 18 are not shown. The segment sent at t=4 is lost, as is the ACK segment sent at t=7. TCP sender t=1 T t=2 t=3 t=4+ t=5- t=6+ t=11 t=12 t=13 t=14 t=15 t=16 t=17 t=18 I data segment data segment data segment data segment data segment data segment data segment data segment ACK ACK ACK ACK ACK ACK Ty A A V V htt TCP receiver t=6 t=7 t=8 t=9 t=10 t=11 t=12 t=13 What does the sender do at t=17? You can assume for this question that no timeouts have occurred.
Consider the Go-Back-N (GBN) and Selective Repeat (SR) protocols with a sender window size of 4 and a sequence number range of 1024. For each of these protocols, describe what happens for the following cases: The first packet in the sender window size is lost before reaching the destination. All transmitted packets reached the destination except the third one. Only the first and last packets in the sender window size reached the destination. Only the ACKs of the first and last packets, in the sender window size, reached the destination.
Consider four Internet hosts, each with a TCP session. These four TCP sessions share a common bottleneck link - all packet loss on the end-to-end paths for these four sessions occurs at just this one link. The bottleneck link has a transmission rate of R. The round trip times, RTT, for all fours hosts to their destinations are approximately the same. No other sessions are currently using this link. The four sessions have been running for a long time. i) What is the approximate throughput of each of these four TCP sessions? Explain your answer briefly. ii) What is the approximate size of the TCP window at each of these hosts? Explain briefly how you arrived at this answer.
In the discussion of ARQ protocol in Section 3.3.3, a scenario was outlined that resulted in the receiver accepting two copies of the same frame due to a loss of acknowledgement frame. Is it possible that a receiver may accept multiple copies of the same frame when none of the frames (message or acknowledgement) are lost?
Consider the datagrams of each layer in the TCP/IP model, e.g., Frame at the Link Layer, Packet at the Internet Layer. Explain the functioning of the following protocols based on their datagram header fields only. Note: You do not need to describe the header field but based on the header field, explain how the protocol works, e.g., Acknowledgement field in a TCP Header is responsible for providing reliable data transfer and in case of data loss or ACK not received, segment is re-sent. You do not need to consider every field of the headers but wherever there are more than 4 fields, then based on 5 fields, describe its functioning, if less than or equal to 4 fields then consider all the fields. Ethernet Frame 11 Frame IPv4 Packet IPv6 Packet TCP Segment UDP Segment HTTP
NAKs are handled in protocol 6's code for frame arrival.If the incoming frame is a NAK and another condition is satisfied, this section gets activated.Describe a situation in which this other condition is critical.
Consider the Go-Back-N (GBN) and Selective Repeat (SR) protocols with a sender window size of 4 and a sequence number range of 1024. For each of these protocols, describe what happens for the following cases:.Only the ACKs of the first and last packets, in the sender window size, reached the destination.