nd the angle between along diagonal and an adjacent face diagonal of a cube..

Q: Explain the statement: "Safeguards must not create interference

A: Safeguards (guards, protective-devices) are protective measures that utilize particular…

Q: Where did the 107.11 came from

A: Given   Weight, W1 = 500 N                 W2 = 1000 N Find   The angle 107.11o

Q: (a) The temperature distribution across a wall of an aluminium cylin- der block, 4 mm thick at a…

A:

Q: Billy Bob is trying to decide whether to push a 50 kg dresser up a 4.5 m ramp or lift it directly…

A: We can answer up to 3 subpart so we will answer first 3. Please resubmit the question by specifying…

Q: . The principal

A: Given data; Uniaxial tensile stress =100 MPa E=200 MPaPoisson ratio,v=0.3 Determine the principal…

Q: A long thin-walled double-pipe heat exchanger with tube and shell diameters of 1.0 cm and 2.5 cm,…

A: Given data d1=1 cmd2=2.5 cmh1=4100 W/m2Kk=0.6 W/m°CPr=7.01 Here, d is the diameter and k is the…

Q: constant throughout the length. ns. Draw the FBD of the beam with the calculated values of the…

A: Given data Point load = 250 kN Distributed load = 75 kN/m Solution are given below

Q: The minimum pressure on an object moving horizontally in water (Ttemperatu at10 degree centrigrade)…

A:

Q: Q1: The following two random variables x and y are linearly correlated: 1) specify their correlation…

A:

Q: AQ2) Air (y = 1.4) flows into a constant-area insulated duct with a Mach number of 0.20. For a duct…

A:

Q: 5. What is the full-load current of a 230-volt, 3-phase, 125-horsepower synchronous motor when it is…

A: Given3phase motor full loadV=230VPower P=125hppower facor ,cosϕ=80%=0.8

Q: In the system shown, a force P(t) is applied at C. Bar ABCD is of negligible mass. Determine: The…

A:

Q: Marisa's car accelerates at an average rate of 2.6 m/s². Calculate how long it takes her car to…

A: Given, Acceleration = a = 2.6 m/s2 Initial velocity = u = 24.6 m/s Final velocity = v = 26.8 m/s…

Q: Question 5 Answer the following questions concisely (no more than half a page per question): a What…

A:

Q: Q2. The force F = 120 lb acts on the frame. Resolve this force into components acting along members…

A:

Q: The force F = 120 lb acts on the frame. Resolve this force into components acting along members AB…

A:

Q: 2 m 1 m For the figure below, the center of :gravity is y₁ 2 m 3 m X'= 2.65 AND Y'= 1.217 O X'=1.217…

A:

Q: Two forces F₁ and F₂ act on the screw eye. If the resultant force FR has a magnitude of 80 lb and…

A:

Q: The temperature distribution across a wall of an aluminium cylin- der block, 4 mm thick at a certain…

A:

Q: The impeller of the centrifugal pump is 350 mm diameter, and the width of the blade passages at…

A:

Q: please send handwritten

A:

Q: In an air-standard Otto cycle engine, the following data were obtained: k = 1.4, cp = 1.0045₂ =…

A:

Q: A boiler produces 25 kg/s of steam at 3 MPa and 600 °C, cools the condenser with seawater so that…

A: Given data m=25 kg/s Here, m is the mass flow rate. The net power output is the difference of power…

Q: Each of three identical bodies satisfies the equation U = CT, where C is the heat capacity of each…

A:

Q: Uniform air flow at Mach 3 passes into a concave corner of angle 15°, as shown in Figure P6.1. The…

A:

Q: Find the loss of head when pipe of diameter 30 cm is suddenly enlarged to a diameter of 40 cm. The…

A: Given:d1=30 cmd2=40 cmQ=300 L/sec

Q: The maximum principle stress for the stress state shown in the figure is (b) 20 (a) o (c) 3 0 (d)…

A: As given in question, Normal stress along x direction = σx = σ Normal stress along y direction = σy…

Q: Figure -2 ft 2 ft 2 in. 2P 2 ft 1 of 1 > B Part A If the beam is made from wood having an allowable…

A:

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy…

A:

Q: CALOTER 3) Determine the moment of inertia of the composite area about the x and y axes y 6 in. T 3…

A:

Q: As shown the figure (a) Calculate the number of instantaneous centers using Arnold Kennedy Theorem…

A: we have to evaluate the number of instantaneous centers

Q: Find the head loss due to friction in pipe of diameter 30 cm and length 50 m through which water is…

A: We must calculate the head loss due to friction in a pipe with a diameter of 30 cm and a length of…

Q: The energy (in 3) released per

A: Given data;  Voltage,v=200 VCapacitance of RC circuit =50 μf Find energy released per spark the IEG…

Q: 99 2) Design the fillet weld for direct shear connection for the angle loaded as shown in the…

A: INTRODUCTION: A fillet weld joint and a butt weld junction are the two most common types of weld…

Q: A reheat cycle with two stages of reheating is executed with steam expanding initially from 20 MPa…

A:

Q: (b) The same engine is connected to a dynamometer which gives a brake output torque reading of 175Nm…

A: As per the guidelines we are subjected to solve only three subparts question at a time please the…

Q: In the figure below, the instantaneous angular velocity of the crank Q2A is 100 rpm,…

A:

Q: 1 Two forces F₁ and F₂ act on the screw eye. If the resultant force FR has a magnitude of 601b and…

A:

Q: 3 he linear velocity of A is represented by Va. Determine the linear velocit fB,C, and D on link 3…

A:

Q: What are the types of thermodynamic cycle as to the type of output? Define each

A: Any closed system that experiences numerous changes owing to temperature, pressure, and volume,…

Q: Q'/ If the fitting symbol between the shaft and hole is (8G7/h6), find? 1-The upper and lower…

A:

Q: (a) The total number of gear teeth on pinion and wheel. (b) The number of teeth on the pinion and…

A: we have to calculate the diameters

Q: The acceleration of a particle is given by a = 2t—10. Determine the velocity and displacement as…

A:

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A: given; gear reduction ratio(G)=2.32center distance(d)=83mmmodule(m)=2mm

Q: Q1) A steel cylinder 10 cm in diameter and 10 cm long is initially at 300 °C. It is suddenly…

A:

Q: A 10.0 kg mass sliding on a frictionless horizontal surface at 8.00 m/s hits a spring that is…

A:

Q: Q2. The force F = 120 lb acts on the frame. Resolve this force into components acting along members…

A:

Q: • Prepare thermophysical property for air from table (A - 17) 1) In "air properties" sheet, create a…

A: Given question: Create a table for air temperature T and air enthalpy h from 300 K to 1100 K with…

Q: A 3200c.c. Spark Ignition (SI) V6 engine operates on a four stroke cycle at 7800RPM. The engine…

A: Spark ignition engine is a constant volume head addition and constant volume heat rejection process…

Q: Q3/ A truss shown in Figure below is made of Aluminium and it consists of two rods. The…

A: