MENG222 Strength of material please I have report lab((Deflection Measurement for Simply Supported Beam))Please i need you write ^^^introduction ^^^just introduction please helpe me for thatGIVE me good introduction with one figure thank you ObjectiveTo determine the deflection in a simply supported beam using the bending bar apparatus.IntroductionHorizontal loading, perpendicular to the longitudinal axis causes bending deformation ordeflection. The loading can be categorized as point central load, uniformly distributed load, oruniformly varying load. In a simply supported beam, the two supports react in the longitudinaland transverse directions.Figure I Simply Supported Beam without LoadL/2L/2Figure 2 Simply Supported Beam with Central LoadingTheoryBending MomentA bending moment is the reaction induced in a structural element when an extemal force ormoment is applied to the element causing the element to bend.DeflectionMeasure of deformation due to transverse loading is called deflection or verticaldeformation from initial point due to external load is called deflection. It is denoted by ô. ApparatusDial gaugeBending Bar ApparatusSimply Supported Steel BeamWeight HangerWeightsRulerVernier CaliperWrench- Allen keyUseful Formulas;I =12bd3- , b is width and d is thickness.PL3Pis load, L is length, and E is modulus of elasticity (steel=200GPA).48EIL= 50cmResults and CalculationsDeflection (6)Increasing Decreasing Average(mm)LoadTheoreticalError(P)DeflectionPercentage(mm)(mm)

The introduction for the above picture is explained below -

MENG222 Strength of material please I have report lab ((Deflection Measurement for Simply Supported Beam)) Please i need you write ^^^introduction ^^^ just introduction please helpe me for that GIVE me good introduction with one figure thank you

MENG222 Strength of material please I have report lab ((Deflection Measurement for Simply Supported Beam)) Please i need you write ^^^introduction ^^^ just introduction please helpe me for that GIVE me good introduction with one figure thank you

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hw: Find the Sslope and defletion in the section CA-A) and the section cB-B) fur the beam Showwn. Given, I = 5*l-"m4 aued Es 205 G Pa. A 2 kulm Im 2.5 m Im A
I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
sted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick 350mm JointB 250 mm Xg = 20x10% Eg = 90 G Pa -6 A, = 12x10/0 Es = 200 G Pa thickness> 16 mm 8 mm bolt %3D 12 mmi thick shear strength f bolf bearing streng th of holt= 100 la 50 MPa %3D Assume no failure will take place in steel or brass. Temperature chauge brass steel on Temperature change on Determine thai can be applied to system - the max
EQuiz No.3 584nkkz1 Cc7KLzOsdr9YUFgvcfFSqpsdlyljtewQ/formResponse Choose the correct answer What will be the value of load applied parallel to the diagonal of (100x100x100))mm cube since the splitting tensile strength=3 Mpa 57.8 KN O 46.7 KN O 47.1 KN O (28)=27.5 Mpa, then the fc(180)=-- for concrete produced using moist
8. H / The beam shown below has across seclion of channel Shape with width 360mm.and haghs h= loomm, the web thickness ist= 14mm.Deler- Mine ihe Max imum tensile aud Compressive stressin the beam due to unifom Load? 360Mm 3.6KN/M 14m tiom Please Sir 5T CASIC f-991ES PL DATURAL u CALC (-)
2. The uniform, 12ON board shown in figure below is supported by two ropes as shown in figure below. Find the T1, T2 and the unknown values of the angle. 30 0.25 L 0.75 L 0.40 kN
Q2. What is the minixim vahe of thickness that can used. Use the inforamtion proviled in the table bekw. (30 Mark) P.(MPa) 6, (MPa) T, (MPa) D (m) SL (mm) S (mm) (mm) (mm) 1.3 14 12 60 30 1.4 90 16
Part A The beam is made of material having an allowable tensile and compressive stress of (o), 125 MPa and (Galow)e = 126 MPa, respectively (Eigure 1) Determine the maximum allowable internal moment M that can be applied to the beam Express your answer to three significant figures and include the appropriate units. Figure 1 of 1> H HẢ Mmax = Value Units Submit Request Answer 300 mes M 0 mm < Return to Assignment Provide Feeatack 30mm 150 mm 150mm
(40 Hiw A Pismatic steel bar ofa Square cross section (loo*lo0)mm is looled by Comressive force P= 1300 kU, the bar has length 2.5 m, Eg=200 G Pa, V=0.3,determine the Shortening d, the increase in the dimensions of cross Section , the change in Volume DV of the bar? loomm Joomm
Q2: Determine the resultant about the point O of the four forces and one couple which act on the plate shown in the Figure below. Note for the resultantot fore es, you 30N 5 m- should compute the magnitudo $K direchion 25N 45 2 m 70 N.M 2 m ZON 1 m 40N 30 Pagel
Photos 4 Crop & rotate Filters * Adjustments 2 Undo all Redo all Crop & rotate Straightening 0 ° Two round bars are joined and used as a tension member as illustrated. The modulus of elasticity is 200 GPa for steel and 70 GPa for aluminum. Rotate D4 Flip O Aspect ratio : Custom Aluminum 100 mm diameter Reset bar 50 mm diaineter P Steel bar +280 mm 400 mm Determine the magnitude of the force P (in kN) that willI lengthen the two bars 0.45 mm. * Your answer Save a copy Cancel 6:50 PM O Type here to search 日 28°C Partly cloudy 4)) ENG 23/09/2021
0: ll zain IQ docs.google.com/forms O no one 0/10 find the tensile stress in upper plate in section 1-1 5 1 80 kN 80 kN B-bolt DIA. 10 MM 80 kN 80 kN B-bolt DIA. 10 MM 30 MPa O 33 МРа 35 MPa 37 MPa no one + ... 300 mm