Mass m₁ = 12.9 kg is on a horizontal surface. Mass m2 8.00 kg hangs freely on a rope which is attached to the first mass. The coefficient of static friction between m₁ and the horizontal surface is μs = 0.560, while the coefficient of kinetic friction is uk = 0.175. m₁ m₂ If the system is set in motion with m₁ moving to the right, then what will be the magnitude of the system's acceleration? Consider the pulley to be massless and frictionless. 2.70 m/s^2 You are correct. Your receipt no. is 157-4031 Previous Tries = If the system is set in motion with m₁ moving to the left, then what will be the magnitude of the system's acceleration? 1.306 m/s^2 Submit Answer Incorrect Tries 1/12 Previous Tries

Mass m₁ = 12.9 kg is on a horizontal surface. Mass m2 8.00 kg hangs freely on a rope which is attached to the first mass. The coefficient of static friction between m₁ and the horizontal surface is μs = 0.560, while the coefficient of kinetic friction is uk = 0.175. m₁ m₂ If the system is set in motion with m₁ moving to the right, then what will be the magnitude of the system's acceleration? Consider the pulley to be massless and frictionless. 2.70 m/s^2 You are correct. Your receipt no. is 157-4031 Previous Tries = If the system is set in motion with m₁ moving to the left, then what will be the magnitude of the system's acceleration? 1.306 m/s^2 Submit Answer Incorrect Tries 1/12 Previous Tries

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

You want to use a rope to pull a 12 kg box of books up a plane inclined 30 degrees above the horizontal. The coefficient of kinetic friction is 0.28.The rope pulls parallel to the incline. What force do you need to exert on the rope if you want to pull the box with a constant acceleration of 0.50 m/s squared yp the plane?
After the block in Fig. P-1405 has moved 10 ft from rest, the constant force P is removed. Find the velocity of the block when it returns to its initial position. Ans. v = 21.2 ft/sec
A 5.740 kg block of wood rests on a steel desk. The coefficient of static friction between the block and the desk is u, = 0.555 and the coefficient of kinetic friction is µy = 0.305. At time t = 0, a force F = 19.2 N is applied F horizontally to the block. State the force of friction applied to the block by Us,k the table at times t = 0 and t > 0. t = 0 t > 0 N Consider the same situation, but this time the external force F is 38.8 N. Again, state the force of friction acting on the block at times t = 0 and t > 0. %3D t = 0 t > 0 N
The homogeneous 18-kg pulley is attached to the bar ABC with a pin at B. The mass of the bar is negligible. The cable running over the pulley carries a tension of 600 N. Determine the magnitudes of the support reactions at A and C. Angle is 40 degrees.
Determine the resultant ?R of the three tension forces acting on the eyt bolt. Find the magnitude of R and the angle θx which R makes with the positive x-axis. Note that F1= 563 N, F2= 345 N and F3= 296 N.
Three people are pulling a heavy object along the floor with forces A, B and C as shown in the figure. What is the resultant (i.e. suml of the three forces? The forces are given by (all angles are CCW from + x-axis): A = magnitude 20 N, direction 30º. B = magnitude 40 N, direction 140°. C= magnitude 30 N, direction 240º. в А х-ахis
There is a block loaded with two 0.5 kg masses and is pulled at constant velocity across the table but with an applied force that is parallel to the surface of the table. theta = 0 because the force is of the same diraction as the displacement. What are the magnitudes of the following forces: Fg FN Ff
Fig. P3-2 33 A homogeneus cylinder weighing 00 Ib sts against two smooth planes that form a trough as shown in Fip. P3. Determine the forces exerted on the cylinder by the planes at contact points A and 8. Fig. P3
Three masses (m3 = 4.00 kg; m2 = 2.0 kg; m1 = 7.0 kg) are connected as shown, with a massless and frictionless pulley. If the coefficient of kinetic friction is 0.200, calculate the tension between the two masses on the inclined plane (elevated at 35 degrees above the horizon). Assume the system begins to move. m
ΣF=ma Ffr = μFN 1m = 3.3 foot 1m = 0.001km A 100 kg bx rests on a horizontal floor. The coefficient of static friction is us = 0.40, and the coefficient of kinetic friction is uk = 0.10. Determine the force of friction Ffr acting on the box if a horizontal applied force FA is a) 50N and b) 600N. ΣF=mw
A series of weights connected by very light cords are given an upward acceleration of 4.00 m/s2 by a pull P, as shown in the figure. A, B, and C are the tensions in the connecting cords. Find the value for each of the tensions A, B, and C.
The collar of mass m = 2.0 kg slides on the rough horizontal shaft under the action of the force Fof constant magnitude F = 13 N but variable direction. If 0 = 0.46t, and if the collar has a speed v = 3.9 m/s to the right when e = 0, determine the velocity vz of the collar when e reaches 90°. Also determine the value of F which renders v2 = V1. The coefficient of friction is u = 0.36. Answers: If F = 13 N, v2= m/s N. If v2 = V1. F =