lical. The tank is topped with a hemispherical steel dome. The wall thickness of the tank and dome is 0.68 in. If the tank is ressurized and contains water 55 ft above its base, and considering the weight of the tank, determine the maximum state stress in the tank and the corresponding principal stresses (normal and shear). The weight density of water is 62.4 lbf/ft³ e maximum tangential stress and radial stress are] psi, respectively Le shear stresses are 1/3= psi, 1/2 psi and psi, and r2/3=1 psi

lical. The tank is topped with a hemispherical steel dome. The wall thickness of the tank and dome is 0.68 in. If the tank is ressurized and contains water 55 ft above its base, and considering the weight of the tank, determine the maximum state stress in the tank and the corresponding principal stresses (normal and shear). The weight density of water is 62.4 lbf/ft³ e maximum tangential stress and radial stress are] psi, respectively Le shear stresses are 1/3= psi, 1/2 psi and psi, and r2/3=1 psi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A water tank 3m in diameter and 6m high is made from 12mm thickness of steel. When the tank is filled with water: - Determine the circumferential stress - And the tension force in the vessel
The cylindrical tank with a spherical end-cap has an outer radius of 2.54m and a wall thickness of 53 mm. if the tank is pressurized to 1.45 MPA. What is the circumferential stress (MPA) in the cylinder? 2 m
An 8 mm thick steel plate has an outside diameter of 600 mm and a length of 3 m. The plate is subjected to and internal pressure of 2 MPa. 54. When the tank is filled with water, determine the circumferential stress in MPa Determine the longitudinal stress in MPa at the bottom of the tank when filled with water.
The spherical tank as shown is made of steel. The tank has a radius 20 ft and wall thickness of 1 inch. If the allowable stress of the steel is 9000 psi, determine the maximum safe pressure for the tank
An upright cylindrical tank 15 m in diameter and 13 m high is completely filled with water determine the minimum thickness of the tank plating if the stress is limited to 40 Mpa.
The cylindrical portion of the propane tank has an outer diameter of 12.02 in. and a wall thickness of 0.13 in. Calculate the longitudinal stress (in psi) in the wall of the cylinder when the tank is pressurized to 162.2 psi.
A vertical cylindrical steel tank 3 m in diameter and 6 m high has a wall thickness of 12 mm. If the tank is filled with water, determine the circumferential stress. Select the correct response: 4.08 MPa 8.16 MPa 7.36 MPa 3.68 MPa
A cylindrical tank with closed ends is filled with compressed air at a pressure of 690 kPa. The inner radius of the tank is 4 m. and it has wall thickness of 10 mm. Determine the magnitude of maximum in-plane shear stress.
When filled to capacity, the unpressurized storage tank shown in Figure contains water to a height of h = 30 ft. The outside diameter of the tank is 12 ft and the wall thickness is 0.375 in. Determine the maximum normal stress on the outer surface of the tank at its base. (Weight density of water = 62.4 lb/ft3.)
A cylindrical steel tank having an internal diameter of 50 in. is submerged in seawater (weight density =64⁢ lb/ft3) to a depth of 9750 ft. The internal gage pressure in the tank is 1600 psi. (a) If the allowable stress of the steel is 32 ksi, what is the minimum allowable outside diameter of the tank? (b) What is the maximum tensile stress before the tank is immersed? Determine the external pressure of the seawater at a depth of 9750 ft. po= psi Determine the maximum magnitude of σr produced in the tank. σr = psi Based on the maximum magnitude of σr produced in the tank from Part 2, is there an outside diameter for which the radial stress magnitude will exceed the allowable stress of the steel in this case? More calculations are needed. No Yes For this case, choose the correct statement regarding the maximum magnitude circumferential normal stress. It occurs at the outer surface of the tank, and it is tensile. It occurs at the outer surface of the tank, and it…
Design the thickness of the cylinder tank in the shown figure if it is to be filled with oil whose density is 790 kg/m³. The maximum stress of the material is 70MPa. Steel tank dimensions are D = 2.5m and L = 4m.
A WATER TANK IS “L1” IN DIAMETER AND “L2” HIGH. IF THE TANK IS TO BE COMPLETELY FILLED, DETERMINE THE MINIMUM THICKNESS OF THE TANK IF THE STRESS IS LIMITED TO 70 MPa. (note: Diam = L1, Height = L2) L1 = 5 L2 = 7