In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000 ft long and 15-inch in diameter. The pipe is commercial steel with roughness 0.00015 ft. Water temperature is 50°F (kinematic viscosity is 1.41 x 105 ft?/s), and the total discharge is to be 4 ft /s? Use g = 32.2 ft/s?. Determine: The velocity, friction factor, and flow rate of water in pipes 1 and 2.

In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000 ft long and 15-inch in diameter. The pipe is commercial steel with roughness 0.00015 ft. Water temperature is 50°F (kinematic viscosity is 1.41 x 105 ft?/s), and the total discharge is to be 4 ft /s? Use g = 32.2 ft/s?. Determine: The velocity, friction factor, and flow rate of water in pipes 1 and 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

pipe 310 m Water is flowing in a straight concrete lining centrifugally spun pipe as shown in the figure problem 12. The difference between the two gauge readings is 185 kPa. The flow rate is designed to be 30 liter/s. By using Darcy Weisbach and Hazen William's formula, determine the pipe diameter. (Ans.: 228 mm, 123 mm) TABLE 5.1: Pipe Characteristies Pipe Hazen-William* Roughness e (mm) 0.15 C 140 Asbestos Cement (AC) – all ages Cast Iron, Ductile Iron - new 0.3 130 10 years old - 20 years old 1.5 3.0 100 90 Cast Iron coated – good condition all ages Welded steel - uncoated - new 0.3 135 125 100 100 - old 0.6 1.5 Coal tar enamel coated steel – new Concrete lining centrifugal spun – all ages Galvanized Iron (GI), Mild Steel (MS) HDPE, UPVC, Polyethylene Wrought Iron Copper, Brass *The Malaysian Water Association - MWA (Design Guidelines for Water Supply Systems) 0.15 0.15 140 0.3 130 0.015 155 0.045 ND 0.0015 ND ND = No Data
Solve for the water discharges in cach steel pipe as shown in Figure 3. You may assume that the minor losses (entrance, exit & bend losses) are negligible. Two trials are enough for this exam. -Elevation 35 m Pipe 1: D-0.2m, L=2400m, f=0.020 Elevation 30 m Elevated tank A -Elevation 28 m Elevated tank B Reservoir C Pipe 3: D=0.15m, L=1500m, f=0.020 Pipe 2: D=0.2m, L=2400m, f=0.020 -Elevation 10 m Figure 3
Q2) i Neglecting minor losses in the pipe, determine the flows in the pipes and 0 the pressure heads at the nodes (kinematic viscosity= 1.13x104m?¥s) F E n I I 30 Data Pipe Ab BC O DE EF AF BE Lengeh (m) 600 600 200 600 600 200 200 Diameter (wm) 250 150 100 150 150 200 100 Roughness size of all pipes = 0.06 mm Pressure head elevation at A = 70 i o.d. Elevation of pipe nodes A 5 c D L ® 028 0 20 2 2
2. A tank and piping system are shown below. The total length of PVC pipe is 2500 ft and discharges water into the atmosphere. The pipeline has an open globe valve and four threaded elbows; h1 = 10 ft and h2 = 45 ft." a. If the discharge is 0.5 cfs, what NPS should be used for the PVC pipe (ks = 0.00006 inch). b. What is the pressure at A, the midpoint of the pipeline? c. Draw the EGL and HGL. h2 Water T = 10°C (50°F) Globe valve
Oil with sp. gr. 0.95 flows at 200 lit/sec through a 500 m of 200 mm diameter pipe (? = 0.0225). Determine (a) the head loss (m) and (b) the pressure drop (kPa) if the pipe slopes down at 10⁰ in the direction of flow.
Oil of viscosity 0.1 Pa.s and specific gravity 0.90, flows through a horizontal pipe of 25 mm diameter. If the pressure drop per meter length of the pipe is 12 kPa, determine (a) the rate of flow in N/min; (b) the shear stress at the pipe wall; (c) the Reynolds number of the flow; and (d) the power required in W per 50 m length of pipe to maintain the flow. [Take: unit weight of water = 9810 N/m³]
Q-Water flows through a pipe having an inner radius of 10 mm at the rate of 36 kg/hr at 25° C. The viscosity of water at 25°C is 0.001 kg/m.s. The Reynolds number of the flow is
H.W.9/7 For the closed tank with Bourdon-tube gauges tapped into it, what is the specific gravity oi thE On ana une pressure reading on gage C? Soil = 0.87 0.5 m Air PA= 50.0 kPa 1.0 m Oil S = 0.8) PB = 58.5 kPa 0.5 m 1.0 m Water 0.5 m Pc=? T= 10°C
Orifice Given:As = 3m2C = 0.92Ao = 0.01m2 Determine the time for the depth of liquid in the tank to be 0.8m
In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000 ft long and 15-inch in diameter. The pipe is commercial steel with roughness 0.00015 ft. Water temperature is 50°F (kinematic viscosity is 1.41 x 105 ft?/s), and the total discharge is to be 4 ft /s? Use g = 32.2 ft/s?. Determine: The velocity, friction factor, and flow rate of water in pipes 1 and 2. (1) A B
FLUID FLOW IN PIPES I. Proving. SHOW THAT 1. R = A/P → D = 4R fyv² 8g 2.T= y (hf)D 4L
15. If the pressure in pipe A is 6 kPa, the SG = 0.85 pressure in pipe B =. ........... psig. Water 90 mm 30% a. 1.27 70 mm b. 8.73 40 mm C. 60.17 SG = 13.6 Mercury d. None of all these