In the next figure.we want to fill the two tanks with water by a pump.The pump is operating manually by a push-button "Start". Whenthe first tank becomes full, the circuit should automatically start tofill the second tank by closing the first valve, and opening thesecond valve, and when the second tank is full, the pumpdisconnects automatically and a "sign lamp" is turned on to showthat 2nd tank is full.Start/StopContact StationFloatSwitch 1FloatSwitch 2Electrically OperatedValve

Step 1:A diagram given states:The pump is operated manually by a push-button "Start" (normally open)…

Answered: In the next figure.we want to fill the…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter3: Magnetic Starters

Section: Chapter Questions

Problem 23SQ

See similar textbooks

Similar questions

Two motors A & B are to be stopped. Motor A is stopped by simply turning off the supply. Motor B is stopped by dynamic breaking. Which statement below is true * Motor A & motor B will stop at the same time Motor A stops faster than motor B Motor B stops faster than motor A
leaving a freevway. Current from the opposite side must travel further, weakening the potential on that side. This creates a potent the motor in that direction, causing the motor to spin. O Only the side where the switch is closed forms a cormplete circuit, so the motor must spin in that direction. Answer the questions and submit the photos for questions 2 -9using the circuit from STEP 2. D2 Yellow R1 50 Q R2 50 0 R3 PSB (+ 5 V 100 aLW R4 D1 100 Q Blue SW1 Sw2 Question 2 本

What percent of the full-load current will be attained after one time constant?
We want to measure the amount of current flowing to an old light bulb. We expect that the result will be around 5A. How should we connect the probes of the multimeter? Drag the connector images to the correct locations and "Not Connected" images to the rest. SUDE SWITCH: LEFT- OFF MIDDLE- DCVOLTS DC mA NUMERICAL VALUE OF VOLTS OR mA OR OHMS DISPLAYED HERE 0.00 OHMS RIGHT - AC VOLTS AC mA OFFOD AC DC-A DM 8010 MOVE ROTARY SWITCH TO THIS AREA TO READ OHMS 1000 200 20 MOVE ROTARY SWITCH TO THIS AREA TO READ VOLTS (SELECT RANGE) 200 (SELECT RANGE) 2K. 20K. •200 20u MOVE ROTARY SWITCH TO THIS AREA TOo READ mA (SELECT RANGE) 200K 20u *200u m 2M 20M 200m 20m 10A COM vn PROBES Windows'u Etkinleştir Windows'u etkinleştirmek için Ayarlar'a gidin. NOT CONNECTED
Devise a circuit that can be used to start a motor and then after a delay of 100s start a pump. When the motor is switched off there should be a delay of 10 s before the pump is switched off.
1. Connect the circuit below S2 2 -12V 32 2. Turn on the switch 1. Describe what happened to the lamp? 3. Turn off the switch 1. Describe what happened to the lamp? 4. Turn on the switch 2. Describe what happened to the lamp? 5. Turn off the switch 2. Describe what happened to the lamp? Procedure Switch 1 Switch 2 1 off on off S1 off off off 10W/12V on off Lamp (On / Off)
We want to make a resistivity measurement. How should we connect the probes of the multimeter? Drag the connector images to the correct locations and "Not Connected" images to the rest. SLIDE SWITCH: LEFT- OFF MIDDLE- DC VVOLTS DC mA NUMERICAL VALUE OF VOLTS OR MA OR OHMS DISPLAYED HERE 0.00 OHMS FIGHT - AC VOLTS AC mA OFFOO AC DC-n DM 8010 MOVE ROTARY SWITCH TO THIS AREA TO READ OHMS (SELECT RANGE) 1000 200 20 MOVE ROTARY SWITCH TO THIS AREA TO READ VOLTS (SELECT RANGE) 20 200 2K 20K. 200 200K 2M 20M MOVE ROTARY SWITCH TO THIS AREA TO READ mA (SELECT RANGE) *20u 200u 200m 20m 10A mA COM PROBES Windows'u Etkinleştir Windows'u etkinleştirmek için Ayarlar'a gidin NOT CONNECTED
Drawing the pneumatic and electric circuit diagramCarrying out the pneumatic and electric circuit constructionChecking the sequence of the circuitProblem DescriptionUsing a cutting device, sheets of paper are to be cut to size.By pressing two pushbutton switches, the cutting blade is advanced and the sheet of paper is cut.After releasing one pushbutton switch, the cutting blade is returned to its start position.
This questions is about Electrical machines , and I need the answer in 30 minutes please
I need a soluion Control Systems
I have an LED that I want to slowly dim and bring back to full brightness. To which area on my Arduino would I connect that wire and why? C B E. 111, CORIA O UNO ARDUINO DE LL A V in OC-to any pin in this area because we are "reading" and not "writing" values D-because we need to power the circuit A- this part of the Arduino controls things OC - but only to pins with a "-" in front of them as this voltage can vary Anode Cathode www.
For the subtractor, if V2 equals 5 volts DC, and V1 is 4 volts DC, then the O/P is .A The answer is 4 volts DC B The answer is 9 volts DC The answer is 1 volt DC .D The answer is 5 volts DC

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS