In the figure shown, use left end of the beam as reference and assume the upward reaction provided by the ground to be uniformly distributed. Write the shear-force and bending moment equations (not simplified and simplified) at each segment. Also draw the free diagrams of each cut/segment. b. Draw the shear-force and bending moment diagrams. Label all significant points in each diagram 98 kN 50 kN/m 50 kN/m |B C |E 1.5 m 2.5 m 2.5 m 1.5 m

In the figure shown, use left end of the beam as reference and assume the upward reaction provided by the ground to be uniformly distributed. Write the shear-force and bending moment equations (not simplified and simplified) at each segment. Also draw the free diagrams of each cut/segment. b. Draw the shear-force and bending moment diagrams. Label all significant points in each diagram 98 kN 50 kN/m 50 kN/m |B C |E 1.5 m 2.5 m 2.5 m 1.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SOLVE THE PROBLEM USING DOUBLE INTEGRATION METHOD Problem I. The beam has a loose fit built-in support at B which allows the end of the beam to rotate through the angle 0₁ = 0.75° when the load is applied, as shown in the detail. E = 72 GPa and 1 = 120 x 10 mm². Determine the following: a. Reaction at A (KN) 200 kN -2 m- b. Moment at B (kN m) c. Slope at A in radians d. Displacement at the application of 200kN load Detail 2 m B
5 Consider the simple beam in Figure 7 with two concentrated loads, where AB=BC=CD=D4m: 6kN 12kN A В C 12m Figure 7 a. Calculate the vertical reactions at points A and D. b. Determine shear force and bending moment as a function of distance x from the point A. Draw the shear-force and bending-moment diagrams. с.
. A beam with the thin-walled cross section in the figure is subjected to a shear force ?=20000lb. (The wall thickness is not shown to scale.). Assume that the thickness of the section isconstant. (a) Determine and sketch the distribution of the shear flows on the flanges and the web.(b) Determine the location of the shear center on the symmetrical line. Point ? is the center ofthe web.
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam. %3D A -L/2- Part 1 Cut a cross-section through the beam between points A and B, and draw a free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x-3,5 m. M(x) A Answer: M(x) - kN-m + mA, eTextbook and Media
Compute the reactions and draw the shear and rnoment curves for the beam in the Figure. Given: E = 200 Gra and I = 120 × 106 mm* B w = 40 kN/m C. 15m 5 in 5m 5m E RES
Q1 A pin-jointed plane truss is pinned at point A and supported on a roller at point E. it carries point loads at point C and D. Using method of virtual work, determine the vertical displacement at joint C. Given the following: 1500mm 200 kN/mm? Area of each member = E 2m C 10 kN 10 kN 3m 3m
The continuous beam is loaded as shown in the figure. The supports at A is pin, B, C, and D are rollers. If there has a support settlement of 18 mm at B, 33 mm at C and 16 mm at D. Use Slope- Deflection in determining the following: a. Reaction at the given supports. b. Shear and moment diagram of the beam E = 210 GPa and l=1350x106 mm4 88 KN 3.6 m 91 kN 74 kN/m 60 KN 40 kN/m D 5m A B 56 kN-m 1.5m 1.5m 1.1 C 2.4m 1.4m 7.3 m 7
Q2: The effect or two forces FA,FB is (5 KN) and acting along u axis , determine the value of FB by parallelogram method (nun perpendicular coordinate) FA-3 kN -****** ************
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0 m and El = 5.5 x 104 kN-m² is constant for the beam. B L/2 L/2 Part 1 Cut a cross-section through the beam between points A and B, and drawa free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x - 3.5 m. M(x) A Answer: kN-m + i m A, M(x) = i eTextbook and Media
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solutions. a. Vertical Reaction at B in kN.b. Moment Reaction at A in kN-m.c. Deflection at point C in mm.d. Deflection at midspan of AB in mm. Valuea = 3.7b = 26c = 29 Thank you very much!
A. Force System 1. Determine the components of the 500N force directed up to the right as shown in the figure. F = 500N Fy 40° Fx
EXERCISE 3.2: A pin-jointed plane truss is pinned at point A and supported on roller at point E. it carries point loads at point C and D. Using method of virtual work, determine the vertical displacement at joint C. Given the following: BL Area of each member E 1500mm 200 kN/mm 2m C E D 10 kN 10 kN 3m 3m B.