In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. P P 1.95in -bb P P 6.25in Determine the dimension b so that the joint is as strong as the boards. inches in 2 decimal places

In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. P P 1.95in -bb P P 6.25in Determine the dimension b so that the joint is as strong as the boards. inches in 2 decimal places

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

4. The two pieces of wood, 2 in. by 4 in., are glued together along the 400 joint shown in Figure 4. Determine the maximum axial load P that can be applied if the shear stress in the glue is limited to 250 psi. 600 N a 30° 100 mm 600 N 150mm FIGURE 4
4. The two pieces of wood, 2 in. by 4 in., are glued together along the 40° joint shown in Figure 4. Determine the maximum axial load P that can be applied if the shear stress in the glue is limited to 250 psi. 600 N 30 150mm FIGURE 4 100 mm 600 N
The two wooden members shown, which support a load P, are joined by plywood splices fully glued on the surfaces in contact. The allowable shearing stress of the glue is 3.5 MPa, allowable tensile stress of the wood is 5.50 MPa and allowable bearing stress of the wood is 8 MPa. From the figure: B = 125 mm gap, t = 6mm L = 150mm Thickness of wood 1 and 3 = 40mm Thickness of wood 2 = 100mm Determine the maximum load P that can be carried by the 40mm wood.
A steel bar is attached to a wood support beam with four 21 mm diameter lag screws, as shown in the figure. The steel bar is 66-mm-wide by 9-mm-thick. The yield strength of the steel is 265 MPa and the ultimate bearing strength is 345 MPa. For the lag screws, the ultimate shear strength is 160 MPa. If a factor of safety of 1.85 with respect to yield strength, 3.5 with respect to bearing strength, and 2.8 with respect to shear strength is required, determine the allowable load P that can be supported by this connection. For the yield strength criterion, consider the constant cross-section part of the steel bar.
A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN 900 kN 80mmØ 100mmØ E = 83 GPa Bronze E = 200 GPa Steel Which of the following most nearly gives the deformation of C? a. -0.7855 mm О Ъ. +0.8575 mm c. +0.7855 mm o d. - о.8575 mm
Question. Two plates each of 50 mm x 500 mm section are glued together along the length to form a section 50 mm x 1000 mm, used as a beam. If the shear force at a section is 1000 N. What is the maximum shear stress on the glue?
A beam is made of four planks glued together. Knowing that the vertical shear in the beam is V = 500 N, determine the minimum required shear strength Tg for the glue. 50 mm 50 mm 50 mm V D B 150 mm 50 mm 150 mm 50 mm
A joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1200 psi for the plywood and 700 psi for the boards. The working shear stress for the glue is 50 psi. Determine the dimensions b and t so that the joint is as strong as the boards.
Q Search MT ACTIVITY 2M Close Activity File Home Insert Draw View Help Open in Desktop App O Tell me what you want to do v 11 ev Av A A Styles v E Tags v abc v Calibri ... SW The composite bar shown in Fig. P-273 is firmly attached to unyielding supports. An axial force P = 50 kips is applied at 60°F. Compute the stress in each material at 120°F. Assume a = 6.5 × 10- Teams Assignments 国 Calendar Calls 6 in/(in-°F) for steel and 12.8 x 10-6 in/(in-°F) for aluminum. Files Aluminum A = 2 in? E = 10 x 10° psi Steel A = 3 in? E = 29 x 10° psi ... 15 in 10 in 田 Help
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?
– A joint is made by gluing two plywood gussets of thickness t to wood boards.The tensile working stresses are 1200 psi for the plywood and 700 psi for the woodboards. The working shear stress of the glue is 50 psi. Determine the dimensions’ b and tso that the joint is as strong as the boards.
Two strips of plastic material are bonded together using splice plates as shown. The average shearing stress in the glue must be limited to 1,050 kPa. If P = 45 kN, what splice plate length L is required? a. 142.9 mm b. 149.2 mm c. 192.4 mm d. 124.9 mm