In the figure, a 110 kg uniform log hangs by two steel wires. A and B, both of radius 1.05 mm, Initially, wire A was 2.20 m long and 1.85 mm shorter than wire B. The log is now horizontal. Young's modulus for steel is 2.00 x 10¹¹ N/m². What are the magnitudes of the forces on it from (a) wire A and (b) wire B? (c) What is the ratio da/de? (a) Number (b) Number i (c) Number Wire A Units Units Units Wire B

In the figure, a 110 kg uniform log hangs by two steel wires. A and B, both of radius 1.05 mm, Initially, wire A was 2.20 m long and 1.85 mm shorter than wire B. The log is now horizontal. Young's modulus for steel is 2.00 x 10¹¹ N/m². What are the magnitudes of the forces on it from (a) wire A and (b) wire B? (c) What is the ratio da/de? (a) Number (b) Number i (c) Number Wire A Units Units Units Wire B

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 44PQ: Consider a nanotube with a Youngs modulus of 2.130 1012 N/m2 that experiences a tensile stress of...

See similar textbooks

Similar questions

A brass wire and a steel wire, both of the same length, are extended by 1.0 mm under the same force. Is the cross-sectional radius of the brass wire more, less, or equal to the cross-sectional radius of the steel wire? Explain. Youngs moduli for brass and steel are 1.0 1010 N/m2 and 2.0 1011 N/m2, respectively.
Consider a nanotube with a Youngs modulus of 2.130 1012 N/m2 that experiences a tensile stress of 5.3 1010 N/m2. Steel has a Youngs modulus of about 2.000 1011 Pa. How much stress would cause a piece of steel to experience the same strain as the nanotube?
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
At a museum, a 1300-kg model aircraft is hung from a lightweight beam of length 12.0 m that is free to pivot about its base and is supported by a massless cable (Fig. P14.38). Ignore the mass of the beam. a. What is the tension in the section of the cable between the beam and the wall? b. What are the horizontal and vertical forces that the pivot exerts on the beam? FIGURE P14.38 (a) From the free-body diagram, the angle that the string tension makes with the beam is = 55.0 + 18.0 = 73.0, and the perpendicular component of the string tension is FT sin73.0. Summing torques around the base of the rod gives (Eq. 14.2): =0:(12.0m)(1300kg)(9.81m/s2)cos55.0+FT(12.0m)sin73.0=0FT=(12.0m)(1300kg)(9.81m/s2)cos55.0(12.0m)sin73.0FT=7.65103N Figure P14.38ANS (b) Using force balance (Eq. 14.1): Fx=0:FHFTcos18.0=0FH=FTcos18.0=[(12.0m)(1300kg)(9.81m/s2)cos55.0(12.0m)sin73.0]cos18.0=7.27103NFy=0:FVFTsin18.0(1300kg)(9.81m/s2)=0 FV=FTsin18.0+(1300kg)gFV=[(12.0m)(1300kg)(9.81m/s2)cos55.0(12.0m)sin73.0]sin18.0+(1300kg)(9.81m/s2)FV=1.51104N
(a) The "lead" in pencils is a graphite composition with a Young's modulus of about 1109 N/ m2. Calculate the change in length of the lead in an automatic pencil if you tap it straight into the pencil with a force of 4.0 N. The lead is 0.50 mm in diameter and 60 mm long. (b) Is the answer reasonable? That is, does it seem to be consistent with what you have observed when using pencils?
A rod of length 4.00 m with negligible mass is hinged to a wall. A rope attached to the end of the rod runs up to the wall at an angle of exactly 45, helping support the rod, while a sign of weight 10.0 N is hanging by two ropes attached to the bottom of the rod. The ropes make an angle of exactly 30 with the rod as shown in Figure P14.79. Another sign with a weight of 10.0 N is attached to the top of the rod with its center of mass at the midpoint of the rod. The entire system is in equilibrium. Find the magnitude of the tension in the rope above the rod that is also attached to the wall. FIGURE P14.79 Problems 79 and 80.
A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?
In the figure, a 134 kg uniform log hangs by two steel wires, A and B, both of radius 1.25 mm. Initially, wire A was 2.50 m long and 1.85 mm shorter than wire B. The log is now horizontal. Young's modulus for steel is 2.00 x 1011 N/m?. What are the magnitudes of the forces on it from (a) wire A and (b) wire B? (c) What is the ratio da/dg? Wire A dindWire B com
In the figure, a 140 kg uniform log hangs by two steel wires, A and B, both of radius 1.25 mm. Initially, wire A was 2.40 m long and 2.15 mm shorter than wire B. The log is now horizontal. Young's modulus for steel is 2.00 × 1011 N/m?. What are the magnitudes of the forces on it from (a) wire A and (b) wire B? (c) What is the ratio da/dg? Wire A Wire B com (a) Number i Units (b) Number i Units (c) Number Units
In the figure, a 140 kg uniform log hangs by two steel wires, A and B, both of radius 1.25 mm. Initially, wire A was 2.40 m long and 2.15 mm shorter than wire B. The log is now horizontal. Young's modulus for steel is 2.00 x 1011 N/m?. What are the magnitudes of the forces on it from (a) wire A and (b) wire B? (c) What is the ratio da/dg? Wire A Wire B d Com
In the figure, a 122 kg uniform log hangs by two steel wires, A and B, both of radius 1.10 mm. Initially, wire A was 2.70 m long and 1.95 mm shorter than wire B. The log is now horizontal. Young's modulus for steel is 2.00 × 10¹¹ N/m². What are the magnitudes of the forces on it from (a) wire A and (b) wire B? (c) What is the ratio da/dB? (a) Number (b) Number i 21918 809.7 (c) Number i 31.2 Wire A Units N Units N Units -da- -dg- com Wire B This answer has no units
In the figure, a 137 kg uniform log hangs by two steel wires, A and B, both of radius 1.20 mm. Initially, wire A was 2.50 m long and 1.75 mm shorter than wire B. The log is now horizontal. Young's modulus for steel is 2.00 x 1011 N/m². What are the magnitudes of the forces on it from (a) wire A and (b) wire B? (c) What is the ratio da/dB? (a) Number i (b) Number i (c) Number i Wire A Units Units Units com Wire B > >