In an experimental set-up, 5 kg of salt solution is heated in a glass vessel by a gas burner. An electric stirrer is used to ensure uniform heating of the solution. The internal energy of the solution is to be increased from 200 to 250 KJ/kg in 15 minutes. The power consumption of the stirrer is 30 W. The rate of heat loss from the vessel is 50W. Determine the power of the gas burner required.

In an experimental set-up, 5 kg of salt solution is heated in a glass vessel by a gas burner. An electric stirrer is used to ensure uniform heating of the solution. The internal energy of the solution is to be increased from 200 to 250 KJ/kg in 15 minutes. The power consumption of the stirrer is 30 W. The rate of heat loss from the vessel is 50W. Determine the power of the gas burner required.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.46P

See similar textbooks

Similar questions

By supplying energy to a house at a rate of 25,000 kJ/hr, a heat pump maintains the temperature of the dwelling at 20 C when the outside air is at -10 C. If electricity costs 8 cents per kW-hr, determine the minimum theoretical operating cost to heat the house for 24 hours. $1.97 O $1.37 $1.75 O $1.51 O$1.64
1. In an analysis, a heat engine based on the Carnot cycle operating between 1000 0C and 300 0C. The heat rejected from this engine to the sink was at a rate of 800 kJ/min. Determine the thermal efficiency (in %) and power output (in kW) of the engin 2.You found out that the power output of your dream car is the same as the sum of each digits of your student number (in kW) with a percentage thermal efficiency the same as the first four digit of your student number divided by 100. The calorific value of the fuel available has a calorific value of 40 000 kJ/kg. Assuming a constant power output from the car, calculate the heat transfer rate (in kW) and the fuel consumption rate (in kg/h)
An electric home stove with 3 burners and microwave is used in preparing a meal asfollows. Burner 1: 20 minutes Burner 2: 40 minutes Burner 3: 15 minutes . Microwave: 30minutes. If each burner is rated at 1.2 kW and the oven at 1.8 kW, and electricity costs 1000(IQ =Iraqi Dinar) per k Wh, calculate the cost of electricity used in preparing the meal?
Refrigerant vapor rejects 70 kW of heat as it passes through an air-cooled condenser. The condenser has an air-side area of 210 m2 and based on this area, has an overall heat transfer coefficient of 0.037 kW/m2∙°C. Cooling air flows at a rate of 7.59 kg/s. If condensation of the refrigerant occurs at 55°C, what is the inlet temperature (in °C) of the air? Take the specific heat of air to be 1.02 kJ/kg∙°C. Round your answer to 2 decimal places.
The coal combustion in the furnace of steam power plant produces p=44.03 mega-Watts (MW) of heating power to produce steam. 0.1*p mega-Watts are lost from the factory infrastructure (pipes, vanes, etc). The depleted steam is cooled by a water cooling system that expels 0.45*p of waste heat to the environment. Calculate the net mechanical power output. Present your answer in mega-Watts (MW).
3. A classroom that normally contains 40 people is to be air-conditioned with window air-conditioning units of 5-kW cooling capacity. A person at rest may be assumed to dissipate heat at a rate of about 360 kJ/h. There are 10 light bulbs in the room, each with a rating of 100 W. The rate of heat transfer to the classroom through the walls and the windows is estimated to be 15,000 kJ/h. If the room air is to be maintained at a constant temperature of 210C, determine the number of window air-conditioning units required. draw a figure also, and explain each step by step solution.
A food compartment is to be maintained at 21°C by a refrigeration system. The total cooling load of the food compartment is estimated to be 330 kJ/h and the heat rejection by the condenser is 480 kJ/h. The outdoor air temperature is 35°C. draw the schematic diagram of the refrigeration system determine the power input required to operate the refrigeration system in kW.
12. Assuming that the Philippines is consuming 3.5×10^20 kWh of electrical energy in one year and the power plant has a conversion efficiency of 32%. Determine the annual heat by the system in BTU. Express the answer in 4 significant figures.
Your company produces small power units that generate electrical energy by expanding the residual process steam in your turbine. You are asked to study the turbine to determine if it is operating as efficiently as possible. One way to ensure good efficiency is to have the turbine operating adiabatically. Gauge shows that for steam 250 degrees and 20 bar: -The working freckle is 86.5 hp -The steam consumpvtion rate is 1000 lbm/h -The steam leaves the turbine saturated at 1 bar Is the turbine operating adiabatically? Base your answers on calculations.
A natural gas-fired condensing boiler has a heating capacity of 38 kW. The fuel heating values are LHV = 49 MJ/kg and HHV = 55 MJ/kg. The boiler efficiency based on HHV is 0.87. Determine the fuel consumption rate in the boiler and the boiler efficiency based on LHV.
You work as a maintenance engineer at Al-Hussein Thermal Power Station that produces electricity. It has a total generation capacity of 260 MW, which consists of two steam power plant units (2 x 130 MW). A. If the thermal efficiency of the first unit is 70%, and that of the second unit is 65%, determine the rate of the thermal energy required to operate the station. B. Determine the rate of waste heat rejection from the station. C. Determine the amount of waste heat energy rejected from the station if it has been operated for 12 hours. D. After certain maintenance operations, the efficiency of each unit is improved to become 80%: 1) How does this improvement affect the rate of thermal energy required to produce the same electrical power 260MW? Compare your answer with that obtained from part A 2) Calculate the rate of waste heat rejection after the improvement? Compare this value with that that obtained from part B. 3) Depending on your results in parts 1 and 2. How do you expect this…
Refrigerant vapor rejects 70 kW of heat as it passes through an air-cooled condenser. The condenser has an air-side area of 210 m2 and, based on this area, has an overall heat transfer coefficient of 0.037 kW/m2∙°C. Cooling air flows at a rate of 7.59 kg/s. If condensation of the refrigerant occurs at 55°C, what is the outlet temperature (in °C) of the air? Take the specific heat of air to be 1.02 kJ/kg∙°C. Round your answer to 2 decimal places.