In a fix bias NPN transistor amplifier, Vcc = 12 V, collector resistor is 5 kOhms and collector current is 1mA. What will be the value of the collector -emitter voltage Select the correct response: O 6V O 5V O 7V O 12V

In a fix bias NPN transistor amplifier, Vcc = 12 V, collector resistor is 5 kOhms and collector current is 1mA. What will be the value of the collector -emitter voltage Select the correct response: O 6V O 5V O 7V O 12V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Find E at the origin due to a point charge of 64.4nC located at (4, 3, 2)m in cartesian coordinates.

A: The Electric field intensity can be calculated by using the coulomb's law.

Q: P4.3. The initial voltage across the capacitor shown in Figure P4.3 is vc(0+) = 0. Find an expres- s...

Q: Why it is preferable to connect bulbs in parallel rather than series? Explain your answer.

A: here they are asked about why the bulbs are connected in parallel rather than series ? first we have...

Q: 6) The following is a block diagram of a feedback control for a DC motor Voltage e(s) speed 5 350(1 ...

Q: What is the capacity factor?

A: Given data: Adam's Bay wind site Wind turbine G80-2000 Pout= 2000kw k=2.05 c=8.35 m/s h=10 m Site ro...

Q: OA wire looo ff long aresisonce af o5ke and an area 94CM. what material is the wire made(T20c).

Q: Determine the Fourier transform of the given signal x(п) - (10)" и(-п + 2)

Q: 10) Define and explain briefly the calibration procedure.

A: Calibration- A comparison of a device with undetermined accuracy to a known device, precise grade/de...

Q: 13. A transformer has a turns ratio of 5. If a 100-2 resistor is connected across the secondary, wha...

A: The turns ratio given in the question is: N1N2=51 The resistance referred to primary can be calculat...

Q: 21. A 100 V source with an internal resistance of 8 N is connected to a 200/100 turns step down idea...

A: Determine the secondary impedance refereed to primary. Z'2=6+j82001002=24+j32

Q: lightly-doped p-type Si region has a hole concentration of 1*10^11 cm-3 at a temperature of 320 K. A...

Q: P4.34. Consider the circuit shown in Figure P4.34. The initial current in the inductor is iL (0-) = ...

A: Please refer the attached images for the complete answer..

Q: 6) The following is a block diagram of a feedback control for a DC motor Voltage e(s) speed 5 350(1 ...

Q: determine

A: Semiconductor Diode: It is a device which is made of semiconductor material that is intended to cond...

Q: Calculate the current lo in the circuit of the figure 10 2 ww. -j4 2 180 2.4/0 A 60/0' V 50

Q: SWA L1 80mH +, ofo t=0 R1 2.2kO VR2 R2 V1 5600 30v t=0 a.Find the equation for IL(t) for t>0. b.Find...

Q: You have semiconductor is equal to or above the bandgap energy, absorbed. For the various radiation ...

A: As per the honor code I will solve first three parts of the question. Kindly repost the other questi...

Q: + Vin VoL R T. 5V

Q: Q1 Assume the Fermi energy level is 0.025 eV below the conduction band energy. (a) Determine the pro...

A: “Since you have asked multiple question, we will solve the first question for you. If you want any s...

Q: Discuss briefly the importance of renewable energy

Q: Question 4: The 3x3 matrix M is given below, in term of a constant k: k 21 M = 4 3. 2 1-2 -1 a) Show...

Q: 18. A 10-kVA, 2400/240 V, single-phase transformer has the following resistances and leakage reactan...

Q: A. Find v. B. Find vn 8 k2 9 V 2 ka 12 ka 8 V 4 ka 20 ka ww

Q: 1. Expand f(x) = x2, 0<x < 2n in a Fourier series. Refer to the figure below. %3D

Q: 1 G1 s+ 1 1 G2 s+ 4 s + 3 G3 s+ 5 1. Three subsystems with the transfer functions G1, G2, G3 are con...

A: In this question we have to find the equivalent tranfer function if they are connected in series and...

Q: A particular magnetic loop antenna has the configuration shown in the figure. Find B at the center o...

A: In this question we need to find B at centre of the given figure.

Q: Assume a leg has 1.1m shaft of bone with an average cross-section area of 3.3cm2. What is a mount of

A: Given data, Length of shaft bone l = 1.1 m Cross sectional area A=3.3 cm2=3.3×10-4 m2 Force applied ...

Q: The diameter of the transducer face (a.k.a. aperture) is 2cm and is focused at a distance of 3cm. Th...

Q: Find the power absorbed by each element in the circuit?

A: The required parameters for the given circuit can be calculated by using basic laws like ohm's law, ...

Q: Example/ Draw the bode plot of the below transfer function, with L = 0.5 & T = 1? e tal G(jw) 1 + jo...

Q: VC 5V D1 R1 Vout 1.5kn silicon diode D2 Germanium Diode

Q: radiation pressure

A: Isotropic radiation- The radiation from a point source which is uniformly radiating in every directi...

Q: 9) Why calibration of instrument is important?

A: The measurement devices are used to measure electrical quantities. The true value and the measured v...

Q: *. 2 6-5-4-3–2-1 567

Q: 10K 10K 5K 5K Vo SK 10K 10K Derive the expression for the output voltage and the find the magnitude ...

Q: 1. An impedance equal to 4.4/60° ohms is connected across a 220volt source. What should be the value...

A: Voltage ampere of load = voltage ×current * Total source power = sum of the each load powers . Tota...

Q: Problem #1: A 6-pole, 3-phase, Y-connected, 60-Hz alternator has 12 slots per pole and 4 conductors ...

A: In this question 3 phase alternator is given....We have to find out pitch factor , distribution fact...

Q: (a) The i/p to the Full wave rectifier is v(t) = 200 sin50t. If RL is 1kΩ and forward resistance o...

A: We are authorized to answer one question at a time since you have not mentioned which question you a...

Q: B: Find current and voltage in the circuit shown In Fig. b 0.51 42 3A

A: Given,

Q: Given: Ả = [-7,4,-4] N ; B = [5,3,-8] N ; = [-2,-5,-3] N ; and D = [-3,4,-5] N %3D Solve for the fol...

Q: P3- Find the value and direction of the current in the 42 resistor using superposition theorem. 22 3...

A: The solution is given below

Q: Define the term "local wide network."

A: The given terms are as follows - 1. Local Network 2. Wide Network

Q: Which is better large B.W or small one? Why? Vcc Rc Rs RB, E Vout CI Vin RBZ ECE. Vs 4.RE Fig-1-. C....

Q: In the circuit shown below, V; is a sine wave with 0 DC bias, amplitude of 5V, and frequency of 60HZ...

Q: Why do we apply reduction factors in the design of electric equipment? Also, why do we increase the ...

A: Reasons for applying reduction factors in the design of electric equipment are as follows: For a ca...

Q: A signal whose highest frequency is 16 kHz is sampled with a frequency of 50 kHz, and 1024 samples a...

Q: Find the load current and power delivered to the load, using thevenin's theorem ? 22 32 24V 82 RL 두

A: We need to find load current and load power for given circuit

Q: If the freauney of information signals is 5K HZ find *The number of pulse in one seconda nd Find the...

A: The frequency is number of cycles or pulses in one second and thus it is 5000 pulses in one second. ...

Q: One great effect of the dialectic or contestation over technology is the innovation that results. Is...

A: A web based and mobile phone based application : Learning platform for coding, A mobile phone servic...

Q: B: Find current and voltage in the circuit shown in Fig. b 0.51 42 3 A ww

A: Apply the nodal equation at the node a. 0.5io+3-i0=0

Concept explainers

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.

Question

In a fix bias NPN transistor amplifier, Vcc = 12 V,
collector resistor is 5 kOhms and collector current is
1mA. What will be the value of the collector -emitter
voltage
Select the correct response:
O 6V
O 5V
O 7V
O 12V

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Why there is a difference between the value of a beta dc and the value of a beta ac in the diagram of output characteristics in transistor
The operating point of the npn transistor is defined by a couple of values: Icand Ver- Select one: OTrue O False In the following figure. Q, and Q: are identicaland operate in active mode. if la =9 Icz then V,V2 IC
. Design a fixed bias-transistor circuit using V = Vcc = 10 V for a Q-point of Iç = 5 mA and Va 4 V. Assume Boc = 100.The design involves finding R, and Rc. inakomeont thot one is hiased
c. For the circuit shown in Figure, determine lc and VCB. Assume the transistor to be made of Silicon. Ic RE=1.6 kn Rc=1.1 kn EE=8 V Vcc= 20 v
H. W. of Lecture L(7-2)C 1. Determine whether or not the transistor in figure above is saturated for the following values: Boc = 125, VBB = 1.5 v, Re = 6.8 kO, Rc = 150 Q and Vcc = 12 V. Rc1.0 kll R Vcc 10 V Bpc=50 10 ks2 VBB 3 V 2. What value of Rc in the figure above will it take to have a voltage gain of 50? Rc 1.0 kn RB Gut Vcc- V, 100 mV
It is connected to the input of a transistor (BJT) amplifier circuit with a gain of "-50" with a peak value of 100mV. a sine sign is applied a) Draw the circuit. b) Underline the input and output voltages by specifying their values.
circuits by using the small signal models of the transistor. Assume the Early voltage of the transistors are infinitely large. Calculate the small-signal input and output impedances of the following Vcc R1 R1 Rout VB RE Rin R2
A field effect transistor (FET) A. Uses a forward bias p-n junction, B. Uses a high concentration emitter junction, C. Has a very high input resistance, D. Depends on flow of minority carrier. As compared to transistor amplifier JFET amplifier has A. Higher voltage gain, less input impedance, B. Less voltage gain, less input impedance, C. Less voltage gain, higher input impedance, D. Higher voltage gain, higher input impedance. The pinch off voltage is the voltage A. At which gate source junction breaks down, B. Which causes depletion regions to meet, C. The voltage applied between drain & source, D. Neither of these. O If properly biased JFET acts as A. Current controlled current source, B. Voltage controlled voltage source, C. Voltage controlled current source, D. Current controlled voltage source.
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
Design-CE255/ purses / Introduction to Electronic Analysis and Design - CE255/E To use it as an amplifier Select one: a. The MOSFET should in the triode region b. The MOSFET should be in the cutoff region c. The MOSFET should be in the saturation region d. The MOSFET could be in saturation or triode region ge Esessment CE255/EE255 (O1) - Dr. Mamoun Al-Mistar Jump to...
The base-biased circuit in the figure is subjected to an increase in junction temperature from 25°C to 75°C. If βdc = 100 at 25°C and 150 at 75°C, Determine the base current Ib in microampere. Show complete solution. (Answer must in 2 decimal places)
Knowing the equation of collector current IC for the transistor amplifier circuit, please calculate the current and voltage stabilization factors. Rc=2000ohm Re=500ohm Rb=500ohm Rb=1000ohm Beta0=200