ild steel rod having a stress of 50 Mpa and having a diameter of 20 mm  What is the force applied

Q: Calculate the stress developed in a steel rod that is 25 mm in diameter when a 70kNaxial tensile…

A: Diameter of rod=d= 25 mm Cross- sectional area= A= (π/4)×d2 = (π/4)×252= 490.873 mm2 Axial load=P=…

Q: A 12 mm thick steel tire has a width of 110 mm has an internal diameter of 800 mm. Tire is heated…

A: Answer: (a) The tensile stress in the tire is 125 MPa. (b) The compressive pressure between the tire…

Q: A cylinder head stud has a diameter of 14mm at the bottom of the thread. If the maximum ten sile…

A:

Q: Example: Compute the tensile strength and ductility (%EL) of a cylindrical copper rod if it is cold…

A: Given Data⇒Cylindrical copper rodFinal dia D2=12.2 mmInitial dia D1=15.2 mmProblem…

Q: 450-mm-long AISI 1020 steel rod is subjected to a tensile load of 55 kN. The allowable tensile…

A: Given Length = 450 mm Tensile load = 55 kN = 55 X 103 N Allowable tensile stress = 140 MPa = 140…

Q: M20 × C4 bolt of mild steel is having yield stress of 320 MPa and factor of safety 3. The safe…

A: Given Data⇒ Bolt dimensions :(M20×C4) Diameter of bolt will be (d)=20 mm=0.020 m Yield stress σy=320…

Q: A tensile load of 1120 lbs is applied to a square bar,1/2 mm on a side and having a length of 5.4…

A:

Q: (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the…

A:

Q: A close-coiled helical spring is to have a stiffness of 90 kN/m and is to exert a maximum force of…

A:

Q: A bar is applied a tensile load of 50 kN having diameter 10 mm,  Calculate the tensile stress induc

A: Given:force, F=50 kNdiameter, d=10 mm

Q: calculate temperature change that will cause a tensile the stress of 90 MPa in the brass rod.

A: Given: Tensile stress =90 MPa To determine: The change in temperature

Q: A 1.2 m pulley is fastened to a 5 in shaft by means of a square key with 140 mm long. What force…

A: Given Data The diameter of the pulley is: D=1.2 m the diameter of the shaft is: d=5 in=127 mm The…

Q: Design a knuckle joint to two connect two co-axial steel rods with 45C8 (S= 380 N/mm) to support a…

A: given data

Q: A cylindrical boiler with an inside diameter of 2.5 m and a wall thickness of 40 mm is made of a…

A: GIVEN DATA- Pressure P=1.5MPa Internal Dia d=2.5m = 2.5*1000=2500mm Thickness t=40mm Yield stress…

Q: A cylinder head stud has a diameter of 14mm at the bottom of the thread. If the maximum tensile…

A: Given data: The diameter of the stud, d = 14 mm. The maximum tensile stress, σ=30 MPa. Write the…

Q: Calculate the stress developed in a steel bar that is 50 mm by 25 mm when a 70kNaxial tensile load…

A:

Q: What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of…

A:

Q: In a tensile strength test a metal bar with initial and final length of 2 in. and 2.195 in.…

A:

Q: Can anyone give a step by step for this? No idea how to approach. Thank you!   The dimensions of a…

A: The 3003 h14 aluminum plate is a medium strength alloy that is made with 1.20 percent manganese. It…

Q: circular rod of 50 mm diameter experience a tensile load of 100 N.  Find the stress induced in ro

A: Given:Diameter of rod, d=50 mmTensile load, L=100 N

Q: Q2: Figure (2) shows an isometric view of a crankshaft that is actuated by the vertical force acting…

A:

Q: The five-bolt connection must support an applied load of P = 2600 Ib. If the average shear stress in…

A:

Q: for a machine part, the following stresses are determined at the most critical point: 0x = 100,0y =…

A:

Q: A tianium disk (roe 107 CPa, Poisson's ratio = 0,34) precisely 8 mm thick by 30 mm diameter is used…

A:

Q: drawing. The bar is threaded through the holes, loaded with fully variable load from the pins. Find…

A:

Q: Stress in the x direction = Blank 1 Stress in y direction ,=Blank 2 Shear Stress on the weld 7 =…

A:

Q: The factors that creep rate depends on? Write 4 of them. Plot the creep-load curve and show its…

A:

Q: 0 kN. Determine the required cross-sectional area of the wable stresses are 6 MPa for concrete and…

A: Need to determine the cross-Sectional area of reinforcing steel

Q: CALCULATIONS 4.1 Using the given pulley radius and the weight values, calculate the torque applied…

A: Disclaimer: Since you have posted a question with multiple sub-parts, we will solve first three sub…

Q: The state of stress at a point in a steel bar is represented in the stress element seen below. The…

A: Given- σy=260 MPaFOS=2

Q: What is the column (small, intermediate or long) if the radius of gyration is greater than the…

A: A column is a vertical member which is subjected to axial compressive load and failure of the column…

Q: Fast

A:

Q: 450 mm long a ISI 1020 Steel long is subjected to a tensile load of 55 kilo Newton the allowable…

A: Given information: AISI 1020 steel: E = 207000 MPa We have to calculate the area of rod using the…

Q: The shaft is pulled by force F. Shaft The yield strength of the material is 500 MPa and the factor…

A:

Q: 1. An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm2. If the cylinder…

A:

Q: Find the size of 14 bolts required for a C.I. steam engine cylinder head. The diameter of the…

A: Given steam pressure=0.12N/mm2diameter of the cylinder =400 mmσ=35MPa

Q: A steel rod bolt 8mm diameter inside fits loosely on an aluminium tube and 16mm outside diameter. A…

A: Given data: The diameter of the steel rod bolt is = 8 mm The outside diameter of the aluminum tube…

Q: Determine the safe tensile load for bolts of M20 and M42 . Assume that the bolts are not initially…

A: We know that ,  when a bolt is subjected to tensile load , Pt=σt×As=σt×πd24 where , Pt=tensile load…

Q: Hooke's Law Part B - Calculate the elongation under load A bar with a solid square cross-section is…

A: Find the total elongation of bar and permanent change in length of bar.

Q: A mild steel cover plate is to be designed for an inspection hole in the shell of a pressure…

A: Given Hole diameter = 120 mm Internal pressure = 6 N/mm2 Cover plate tensile stress = 60 MPa Bolt…

Q: Calculate the design stress when a material has an ultimate strength of 120 psi with a factor of…

A: Answer: The design stress is 165.5 kPa.

Q: A mild steel tie-rod has to carry an axial load of 60KN. The maximum permissible stress is 200N/mm2.…

A:

Q: A steel rod on a bridge must be made to withstand a pull of 6000 Ibs. Find the diameter of the rod…

A:

Q: A cylindrical shape 25.0 mm in diameter and 21.0 mm in height is cut from a pear. Using an Instron…

A:

Q: A steel bolt and sleeve assembly are shown in the figure. The nut is tightened up on the tube…

A:

Q: In the attached picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed…

A: Solution: Given Data: Sy=500 MPa

Q: See figures attached for reference and solve carefully/ellaborately, include the units and draw the…

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.