III. Situational Analysis [Essay 1 – at least 200 words] The ultimate BOD5 from an end-of-pipe discharged to a river of the company where you are working as the pollution control officer was 15 mg/L. At 300 meters downstream, a sampling point was designated by DENR-EMB and found out a measured BOD5 of 120 ppm and a DO of 1.5 ppm. You are the only industry located within 300m radius from the sampling point of the river that stretched about two (2) miles from upstream up to the outfall of a bay. You are summoned for an investigation of the scenario in a technical conference. What would be your technical position or statement of the situation?

III. Situational Analysis [Essay 1 – at least 200 words] The ultimate BOD5 from an end-of-pipe discharged to a river of the company where you are working as the pollution control officer was 15 mg/L. At 300 meters downstream, a sampling point was designated by DENR-EMB and found out a measured BOD5 of 120 ppm and a DO of 1.5 ppm. You are the only industry located within 300m radius from the sampling point of the river that stretched about two (2) miles from upstream up to the outfall of a bay. You are summoned for an investigation of the scenario in a technical conference. What would be your technical position or statement of the situation?

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter3: Collection

Section: Chapter Questions

Problem 3.19P

See similar textbooks

Similar questions

CVE 360 - Environmental Engineering Homework 2 AIUS AMERICA INTERNATIONA UNIVERSIT Problem 1 A wastewater treatment plant is required to disinfect its effluent before releasing treated wastewater into a neighboring stream. An inflow concentration of a certain infectious germ in the wastewater is 25,000 mg/L. A concentration of 2,000 mg/L is the highest concentration that can be released. It is suggested that the disinfection process employ a pipe that carries the effluent. The length of the pipe is 1000 m and the reaction rate constant is 0.1 min¹. Assume that the pipe behaves as a steady-state plug-flow system. Determine a) The residence time of this system (min) b) The speed of flow in this system (m/min) c) If the pipe has a diameter of 250 mm, determine the flow rate in the pipe (m³/hr) Cin 25000 mg/L L = 1000 m pipe = Cout 2000 mg/L k = 0.1 min 1
02: a)What precautions should we follow when conducting experiment in Environmental lab? b)How can you determine chloride content in a waste water sample? Subject is Environmental Engineering Plz solve it?
Wastewater discharges from two businesses were sampled. The BOD concentrations from Company “A” and Company “B” were 400 mg/L and 250 mg/L within DO concentrations 2.5 mg/L and 6.2 mg/L, respectively. Which company discharge would cause the greatest reduction in Nitrogen concentration (nitrification) in the body of water the discharge was flowing into? Group of answer choices B A and B None of these A
Q 01: a) What precautions should we follow when conducting experiment in Environmental lab? b) How can you determine chloride content in a waste water sample? Subject: environmental engineering ii lab
Q- Civil (Environment) An industrial waste water enters a stream having a BOD concentration of 10 mg/l and a flow of 20 m³/sec. If the flow of waste water is 1.5 m³/sec & its BOD concentration is 250 mg/1, then the BOD concentration in the stream at a point downstream of the point of confluence of waste water with the stream will be?
Q.` The wastewater having an organic concentration of 54 mg//is flowing at a steady rate of 0.8m³ /day through a detention tank of dimensions 2mx4mx 2m. If the contents of the tank are well mixed and the decay constant is 0.1 per day, the outlet concentration (in mg//, up to one decimal place) is
QUESTION 3 ' (a) There are various type of flow measuring equipments available beside the pitot static probe and the obstruction flowmeter. An engineer needs to decide the suitable flowmeter to be installed in a toxic piping system. As a trainee engineer, your task is to assist the engineer in deciding the type of flowmeter that to be used. Decide and justify on a suitable type of flowmeter to be used.
Q: What precautions should we follow when conducting experiments in the Environmental lab? How can you determine chloride content in a wastewater sample? subject: Environmental Engineering-ll (lab) program: BE-Civil Engineering
Your organization has been hired to provide a water treatment process or device toremove toxic Chromium 6 [Cr(VI)] from water emanating from an underground source.Your organization has developed a treatment process that removes most of the Cr(VI)from the water to a residual concentration of 0.05 mg/L which is an acceptable level inline with the World Health Organisation. The underground water flows at 40 m3/h andhas Cr(VI) concentration of 100mg/L. The effluent flow rate is 97% of the influent flowrate, and the remainder of the water is discharged as wastewater. Calculate theconcentration of Cr(VI) in wastewater.
15 How absorption can help in pollution control process ?
A large wastewater treatment facility, with an average flow of 220 MGD, has an average influent SO42- concentration of 400 mg/L as SO42-. The wastewater treatment facility has a large-scale biological odor control station at its headworks, with foul air treatment capacity of 180,000 cfm. The average H2S (in gas phase) concentration in the odor control station's inlet air stream is 200 PPMY/v. Please answer the following Estimate the total sulfur loadings in Ib per day (in the form of element S) from the influent sewer?
Environmental Engineering Lab what is the Standard test method to determine biochemical oxygen demand of a given water sample Please add your answer this : Theory Significance Guidelines Apparatus / ChemicalsUsed Procedure