If the temperature of the 85 mmmmdiameter post CD is increased by 60⚫C, determine the force developed inthe post. The post and the beam aremade of A-36 steel, and the momentof inertia of the beam is | = 255 (106)mm4.Figure1 of 1the temperature of the 85 mm-diameter post CD increased by 60 "C determine the force developed in the post. The post and the beam are made of A-36 meel, and the moment of the255 (30)Express your answer with the appropriate unitsBesUnits

Answered: Image /qna-images/answer/8368c739-fe74-4b7e-bdbc-20711d1bf950.jpg

Answered: If the temperature of the 85 mmmm…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rod BD is made of material with G1= 33 GPa has a diameter 46 mm is bonded to the tube CA at point B, the tube made of material with G2=56 GPa has an outer diameter 97 mm and wall thickness of 8 mm. If T1=1268 N.m and T2=2282 N.m, answer the following questions: The polar moment of inertia of the rod BD is The polar moment of inertia of the tube CA is The maximum shear stress of the rod BD is The maximum shear stress of the tube CA is The maximum shear stress of the assembly is The angle of twist between D and B is The angle of twist between C and A is The angle of twist at D is The angle of twist between C and B is The reaction at point A is
The beam AB has a moment of inertia I = 475 in4 and rests on the smooth supports at its ends. A 0.75-in.- diameter rod CD is welded to the center of the beam and to the fixed support at D. If the temperature of the rod is decreased by 150°F, determine the force developed in the rod. The beam and rod are both made of A-36 steel.
3. The rigid bar AB is supported by two rods made of the same material. If the bar is horizontal before the load P is applied, find the distance x that locates the position where P must act if the bar is to remain horizontal. Neglect the weight of bar AB. L = 3 ft A = 0.2 in.2 L = 2 ft A = 0.4 in.2 х X B 10 ft
inches, determine the mass of the heaviest cylinder. Neglect friction and the weight of the rigid bar AB A uniform cylinder is supported by a rigid bar AB and cable BC as shown in the figure. If the stress in the cable is not to exceed 7.25 ksi and diameter of 0.50 18 Ft B 18 Ft 12 Ft
The rigid beam is supported by three 25-mm diameter A-36 steel rods. If the beam supports the force of P=230 kN, determine the force developed in each rod. Consider the steel to be an elastic perfectly plastic material. Detailed solution
Problem # 1: A rectangular bar is subjected to tensile forces of 2230 KN. Use E = 110 GPa and v = 0.34. Determine the change in the dimension of its cross-section along X and Z directions. Also, calculate the change in the volume of the bar. 80 mm 90 2230 KN 2230 KN Y 1.75 m
The stepped rod is made up of two different materials A and B of lengths 80 cm and 1.2 m respectively. The diameters of materials B and A are 2.5 and 3.5 cm respectively. The modulus of elasticity of materials A and B are 250 and 150 GPa respectively. The elongation of the rod is the same for both the materials. A total tensile load of 40 kN is applied to both the materials A and B together. Calculate the load in each material.
1-Determine the elongation of the steel bar 1m long and 1.5 cm cross-sectional area when subjected to a pull of 1500 kg. Take E=2*10 kg/cm ?
The assembly is used to support the 130-kg container having a center of mass at G. The spring has an unstretched length of 250 mm and stiffness of k = 300 kN/m. (Figure 1). Figure 3 m B Part C 2 m 0 2 m 1 of 1 μĂ Part A NB = 1765.8 Determine the heighth of the spring. Express your answer to three significant figures and include the appropriate units. h = 246 mm Submit ✓ Correct Correct answer is shown. Your answer 246.076 mm was either rounded differently or used a different number of significant figures than required for this part. Part B Previous Answers Determine the reaction at the roller A. Express your answer to three significant figures and include the appropriate units. μА NA = 2501.55 Determine the reaction at the roller B. Express your answer to three significant figures and include the appropriate units. Submit Previous Answers Request Answer N N X Incorrect; Try Again; 3 attempts remaining = ? Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts…
Three rods jointly support a 8kN load. Assumingthat there was no stress in the rods before theload was applied, find the stress in each rod.θ = 25oα = 20o Properties:Modulus ofElasticityCrosssectionalAreaSteel 200 GPa 250mm2Bronze 83 GPa 250mm2 L = 2.75 m
Find the reaction at A due to the uniform loading and the applied couple. The force reaction is positive if upward, negative if downward. The moment reaction is positive if counterclockwise, negative if clockwise. 2.5 kN/m 11.1 kN-m A 2.0 m 2.0 m Answers: RA = i kN MA = i kN-m
The force P is applied to the bar, which is made from an elastic perfectly plastic material. Construct a graph to show how the force in each section AB and BC (vertical axis) varies as P (horizontal axis) is increased. The bar has cross-sectional areas of 1 in2 in region AB and 4 in2 in region BC. Take sY = 30 ksi.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS