If the critical commutation time is 2 ms but it was observed that the practical commutation took 2.5 ms. This is the case of __________ a) under commutation b) over commutation c) critical commutation d) none of the mentioned

Q: State assumptions to represent the multimachine equations with a single machine infinite bus system.

A: Multi-machine system can be written similar to a one-machine system by the following assumptions: 1.…

Q: In your own words and from your own understanding, avoid plagiarism or copying from the Course…

A: Power system requires transmission of power from generation end to the consumer end. The power…

Q: .Analyze and Comparison of Voltages at PQ bus and PV bus. 1. At the PQ bus, the value of voltage is…

A: The first step in the analysis is the suitable equations for the power flows in the system. The…

Q: 6.13 give two ways in which over commutation can occur.

A: The detailed answer to the given question is solved below according to the given parameters and…

Q: How can you calculate the maximum short-circuit current that can pass when the A-B ends of an outlet…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: What are the possible faults in underground cables. Illustrate the methods of fault localization.

A:

Q: Define interlocking in electrical systems. What is it's significance?

A: According to the given question, it is required to define interlocking in electrical systems along…

Q: What variable remains constant for both series only and parallel only connections?

A: Series - CURRENT parallel - VOLTAGE

Q: This site is a failure. It rejects all questions and does not solve them in a timely manner

A: We are sorry for that.

Q: The NEC requires that each service-disconnecting means be suitable for A. the prevailing…

A: The service disconnecting mechanisms used to isolate a building's premises wire from the utility…

Q: 8- Generally as of the operating voltage which of the following options are the correct words that…

A:

Q: b) According to your diagram, express the absolute method error in power measurement by defining the…

A: b)

Q: When installing raceways underground in rigid nonmetallic conduit and other approved raceways, there…

A: To find the cover distance in installing underground raceways in rigid non-metallic conduit.

Q: 1. Explain the following terms with respect to the simple differential scheme: Circulating current,…

A: Differential protection relay is a relay whose functioning is based on the phase difference of two…

Q: and installation fluorescent lamp withe Electrical Choke and Tube Light Starter and One-way-switch ,…

A:

Q: 1-Explain the concept of "RELIABILITY OF SERIES AND PARALLEL SYSTEMS

A:

Q: In solar module, minimum value of shunt resistance could be 300 Ohm. Select one: True False

A: In solar module, minimum value of shunt resistance could be 300 Ohm.  Select one: True False

Q: question: 1. Discuss the mechanism of a short circuit and how it can lead to accidents.

A: Short circuit- Electrical current always try to flow least resistive path. Hence in case if…

Q: Describe briefly circling the block diagram of fixed speed wind energy systems.

A: The short terms involved in the figure above are; SCIG :  Squirrel cage induction generator PCC :…

Q: 2. Explain over modulation.

A:

Q: What is a closed path made of several branches of the network called? Select the correct response:…

A: Select the correct option : The closed path made of several branches of the network called :…

Q: Lockout is required: During servicing and maintenance where unexpected ener- gization or start-up of…

A: Bartleby has policy to solve only first question and if it has subparts then solve only first 3…

Q: What's the maximum percent overshoot %OS for this system with its closed-loop poles as shown? jo 12

A:

Q: Question 2: What needs to be done to make an open-loop system to closed-loop? Explain with your own…

A: The system in a control system is described by the transfer function of the system. The control…

Q: What is solid grounding? For an underground neutral system explain the circuit behavior under single…

A: Solid grounding: The solid grounding refers to a situation in which the power system equipment like…

Q: Discuss the mechanism of a short circuit and how it can lead to accident

A: Short circuit- Electrical current always try to flow least resistive path. Hence in case if…

Q: Is this statement TRUE or FALSE?, "The voltage drops to totally zero value in the event of…

A:

Q: 14. Which of the following types of grounding system should be installed in a patient care area? A.…

A: A power station is to provide electricity to a huge number of people. Different customer’s power…

Q: explain span length for ovehead service line

A: Span Length:- The span length is the distance between the two neighboring poles.  It is often…

Q: 6-streets traffic light controller

A:

Q: . What is “accessible” as applied to wiring methods? What is “accessible” as applied to equipment?…

A: In an electrical system, there are various terms which are used for different phenomenon and gives a…

Q: Write a project management report that includes surveying, excavation, groundwater extraction,…

A: The cutoff is essentially a wall built into the foundation with impermeable material to limit the…

Q: this is not incomplete, and please do not answer its functioning of parts answer should be on point…

A: It is asked to explain the isolated operation of wind farms.

Q: What is the name and purpose of the following components of the Arduino board:

A: 1. Digital Pins There are 13 digital pins available in the Arduino. These pins will act like input…

Q: Describe how a fault in long cable can be detected and located using partial discharge technique…

A: The partial discharge technique of high voltage is the best technique for the detection of failure…

Q: MMF method is called pessimistic method as the regulation calculated is always more than the actual…

A: Given statement MMF method is called pessimistic method as the regulation calculated is always more…

Q: Explain fault ride through for wind farms

A: Fault ride through : It is also known as under-voltage ride through. In electrical power power…

Q: A 4.5-kVA, 240 volt electric clothes dryer contributes _____ amperes to the neutral load , when…

A:

Q: How does peak time, settling time, and percent overshoot relate with pole location of the…

A:

Q: In reference to the load, how are MOVS connected to help prevent voltage spikes and surges? Are MOVS…

A: MOVs (Metal oxide varistors) is a variable resistor whose resistance is changed with respect to…

Q: Protective relays used to prevent the fTaults in power system O True O False

A: The function of the protective relay is to detect the fault in the system and remove the faulty…

Q: Explain why the low voltage problem at higher loading is more severe in an uncompensated over-head…

A:

Q: 7- The power system operation can be considered as.. 8- Bus-bar current limiting reactors added…

A: 7. Power systems operation can be considered as close loop system. Because generation depends on the…

Q: 6) With the choice of K as in question 5, is the closed loop system stable?

A:

Q: Question: In step down chopper during off period chopper gets turned off due to the Option 1: Both…

A:

Q: No plagarism please! Correct and detailed answer will be Upvoted else downvoted. Thank you!

A: As per the guidelines of Bartleby we supposed to answer first three subparts of the question for…

Q: open and short concept in cabling

A: In cabling, there may be a possibility of fault that can be classified into two: Open circuit fault…