How does discharge pressure affect the compressor speed? How does discharge pressure affect the power requirements of a reciprocating air compressor? What is meant by overall compressor and motor efficiency ? How does discharge pressure affect the overall efficiency the reciprocating air compressor and motor unit ?

How does discharge pressure affect the compressor speed? How does discharge pressure affect the power requirements of a reciprocating air compressor? What is meant by overall compressor and motor efficiency ? How does discharge pressure affect the overall efficiency the reciprocating air compressor and motor unit ?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter49: Operation, Maintenance, And Troubleshooting Of Chilled-water Air-conditioning Systems

Section: Chapter Questions

Problem 1RQ: How does the compressor lubrication system differ for reciprocating and centrifugal compressors?

See similar textbooks

Similar questions

Air enters a multistage compressor of a jet engine at 0.65 atm and 275 K with a flow rate of 63.5 kg/s. The compressor has an overall pressure ratio of 24:1 and an isentropic efficiency of 94%. Deter- mine the power required to drive the compressor and the temperature of the air at the compressor outlet. P =0.65 atm T = 275 K rit = 63.5 kg/s Win=?
What is the difference between the clearance volume and the displacement volume of reciprocating engines?
Critically compare how heat transfer efficiency will affect the lifetime of the turbine.
what is the mechanism of natural gas Compressors?
combined heat rate, and the total throttle flow for the rated power. (5)A steam power plant operates on the cycle shown in the figure. If the isentropic efficiency of the turbine is 87 percent and the isentropic efficiency of the pump is 85 percent, determine (a) the thermal efficiency of the cycle and (b) the net power output of the plant for a mass flow rate of 15 kg/s. 152 MP 625'C 15.9 MPa 35°C Boiler
QI/Calculate the power in kilowatts of the gas turbine power plant has a greatest temperature of 700°C and a pressure ratio of 10. The isentropic efficiencies of the turbine and compressor are 0.85 and 0.82 respectively. The mass flow rate of the air that inlet to the compressor is 15 kg/s at 15 °C. At the expansion process take Cp= 1.11 kJ/kg:K, y=1.333, and at the compression process take c,= 1.005 kJ/kg K, and y =1.4
on (sat vapor) o, Py 0.14MPa @Ty Rizia (®) tig- 1340 =7 © ¥y =1 om/kg) (@ Ta= (©) Miomy ) Qo= @) BSvura =2 Comdenser) An adiabatic compressor works with R-134a as working fluid and 0.15 KW. The refrigerant enters compressor as saturated vapor at 0.14MPa. The refrigerant leaves compressor at 70°C and 1.2MPa and then enters condenser 10 be cooled at which pressure remains constant and leaves condenser at 40°C. If the surrounding temperature is 30° Find: (a) initial temperature (T1). (b) mass flow rate of R-134a, (¢) volumetric rate of R-1342 at entrance. of compressor ( ¥;). (@) T, . (¢) compressor efficiency, (1) rate of heat Tosses from condenser, and (g) fotal entropy generation in condenser and also show if the process is possible or not.
28. In a marine gas turbine unit a high-pressure stage turbine drives the compressor, and a low-pressure stage turbine drives the propeller through suitable gearing. The overall pressure ratio is 4: 1, and the maximum temperature is 650°C. The isentropic efficiencies of the compressor, H.P. turbine, and L.P. turbine are 0.8, 0.83, and 0.85 respectively, and the mechanical efficiency of both shafts is 98%. Calculate the pressure between turbine stages when the air intake conditions are 1.01 bar and 25°C. Calculate also the thermal efficiency and the shaft power when the mass flow is 60 kg/s. Neglect kinetic energy changes, and pressure [Ans. 1.57 bar; 14.9% ; 4560 kW) loss in combustion.
An ammonia compressor operates at an evaporator pressure of 316 kPa and a condenser pressure of 1514.2 kPa. The refrigerant is subcooled 5 degrees and is superheated 8 degrees. A twin-cylinder compressor with bore to stroke ratio of 0.85 is to be used at 1200 rpm. The mechanical efficiency is 77%. For a load of 87.5 kW, determine: (a) the volume flowrate of cooling water in the condenser if the increase in temperature is 7 degrees, (b) the bore and stroke, (c) the size of the driving motor, and (d) the quality of the refrigerant entering the evaporator
At the beginning of the compression process of an air-standard Diesel cycle operating with a compression ratio of 18, the temperature is 300 K and the pressure is 0.1 MPa. The cut-off ratio for the cycle is 2 and mass flow rate in the system is 1900 kg/hr.cp = 1.006 kJ/kg K cv = 0.717 kJ/kg K calculate the thermal efficiency of the cycle in %? Answer to 1 decimal place.
The catalogue for a refrigerant 22, four-cylinder, hermetic compressor operating at 29 r/s. a condensing temperature of 40 °C and an evaporating temperature of -4 °C shows a refrigeration capacity of 96.4 kW. At this operating points the motor (whose efficiency is 90 percent) draws 28.9 kW. The bore of the cylinders is 87 mm and the piston stroke is 70 mm. The performance data are based on 8 °C of subcooling of the liquid leaving the condenser. Compute 3.1 the actual volumetric efficiency and 3.2 the compression efficiency.
At the beginning of the compression process of an air-standard Diesel cycle operating with a compression ratio of 18, the temperature is 300 K and the pressure is 0.1 MPa. The cut-off ratio for the cycle is 2 and mass flow rate in the system is 1900 kg/hr.cp = 1.006 kJ/kg K cv = 0.717 kJ/kg K 1. calculate the thermal efficiency of the cycle in %?Answer to 1 decimal place. 2. calculate the work output of the engine in kW?Answer to 0 decimal place.