Strain and Stress equilibrium problemsPlease do create a free body diagram 29,000 ksi = (29k)(300")(A)( .1")Solve for AA = 3 in2Use A to solve for diameterd = 1.95"HOMEWORK:A 24-inch long. round A36 steel rod resists a tensile load of 10,000#a.) What is the required diameterlif its unit stress may not exceed 24,000 psi.b.) What is the required diameter if lits elongation is not to exceed 0.005"?Tips:recall how to calculate the area of a circleconsider each of your formulas, which can be used to obtain the information asked for in the questionremember elongation (a kind of deformation) will change areaARC 2580SPRING 2020 MDC-KENDALLWALKER

Answered: Image /qna-images/answer/0285a92d-43fc-4d59-ac41-e6a56e8b4176.jpg

HOMEWORK: A 24-inch long. round A36 steel rod resists a tensile load of 10,000# a.) What is the required diameterlif its unit stress may not exceed 24,000 psi. b.) What is the required dlameter if its elongation is not to exceed 0.005"? Tips: recall how to calculate the area of a circle consider each of your formulas, which can be used to obtain the information asked for in the question remember elongation (a kind of deformation) will change area ARC 2580 SPRING 2020 MDC-KENDALL W

HOMEWORK: A 24-inch long. round A36 steel rod resists a tensile load of 10,000# a.) What is the required diameterlif its unit stress may not exceed 24,000 psi. b.) What is the required dlameter if its elongation is not to exceed 0.005"? Tips: recall how to calculate the area of a circle consider each of your formulas, which can be used to obtain the information asked for in the question remember elongation (a kind of deformation) will change area ARC 2580 SPRING 2020 MDC-KENDALL W

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Manual Calculation 2: Refer to image shown. Decimal Places: 2 Use hand calculations, modeling is not necessary The "Shaft" carries a torque that induces a shear force in the "Bolts". Shear Stress in the 4 bolts (kN/m³) S = 40,000 "Bolt" spacing (m) C = 0.24 "Bolt" diameter (mm) d = 30 "Shaft" diameter (m) D = 0.15. Assume each "Bolt" carries the same shear force. What is the Torque (kN-m) carrying capacity of the shaft? 4 Typ (d) Bolt Shaft
sub=6 solve 30-40 minutes hand written asap..i'll rate
The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are rotated through 180°? Assume the radius of the bicycle wheel is 12.7 inches. The bicycle will travel approximately (Round to the nearest tenth.) in. C -1.95 in 4.21 in
Write the solution for the following: Member BC = -447.21 Member DF = -800 Member CE = 100
solve part (iv)
6 solve 6 show complete STEP BY STEP solution, and draw a FBD.
Frame and Machine From the figure, the load at G is 12 kN: 450 900 500, 600 1000 To determine: a) Piston force JL b) Pin force E and M c) Pin force D andC 600 M 450 Draw the FBD: 600 450 B - All necessary parts to get the piston force JL D. 450 450 300 Analytical Solution. Two decimal numbers for the calculation Dimensions in millimeters 1000
Solve it correctly ASAP NEED! given: T= 5.67
a) If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the maximum allowable stress in the pipe is 7.5 x 109 N/m2 , calculate the minimum wall thickness required for the pipe. Give your answer in millimetres (mm) to 2 decimal places. b)A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under tension. If the wire length extension is 2.5 mm, calculate the stress in the wire. Give your answer in N/m2 to 2 decimal places.
QUESTION 2 A shaft rotates at 300 rpm. 1). If it carries a spur gear that delivers 5 hp to a mating gear and the spur gear has the diametrical pitch of 10, pressure angle of 20°, and 80 teeth, determine a). The resultant force exerted on the shaft = Ib 2). If it carries a sprocket that delivers 4 hp to a mating sprocket and the sprocket has the pitch diameter of 6", determine b). The force exerted on the shaft Ib 3). If it carries a "flat-belt pulley" (Note: NOT V-Belt Drive) that delivers 8hp to another flat-belt pulley and the pitch diameter of the pulley is 20", determine C). The force exerted on the shaft: Ib
Frame and Machine From the figure, the load at G is 12 kN: 450 900 500, 600 1000 To determine: a) Piston force JL b) Pin force E and M c) Pin force D and C 600 M 450 600 450 D. 450 450 300 Analytical Solution. Two decimal numbers for the calculation Dimensions in millimeters 1000
PLEASE SOLVE USING D'ALEMBERTS METHOD