H.W.6: A hollow circular cold-rolled bronze [G, = 6,500 ksi] tube (1) with an outside diameter of 1.75 in. and an inside diam- eter of 1.25 in. is securely bonded to a solid 1.25-in.-diameter cold-rolled stainless steel [G, = 12,500 ksi] core (2) as shown in Figure and the allowable shear stress of core (2) is 60 ksi. Determine . The allowable shear stress of tube (1) is 27 ksi, (a) the allowable torque T that can be applied to the tube-and- core assembly. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced in a 10-in. length of the assembly by the allowable torque T. (1) FIGURE

H.W.6: A hollow circular cold-rolled bronze [G, = 6,500 ksi] tube (1) with an outside diameter of 1.75 in. and an inside diam- eter of 1.25 in. is securely bonded to a solid 1.25-in.-diameter cold-rolled stainless steel [G, = 12,500 ksi] core (2) as shown in Figure and the allowable shear stress of core (2) is 60 ksi. Determine . The allowable shear stress of tube (1) is 27 ksi, (a) the allowable torque T that can be applied to the tube-and- core assembly. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced in a 10-in. length of the assembly by the allowable torque T. (1) FIGURE

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

H.W.6: A hollow circular cold-rolled bronze [G, = 6,500 ksi] tube (1) with an outside diameter of 1.75 in. and an inside diam- eter of 1.25 in. is securely bonded to a solid 1.25-in.-diameter cold-rolled stainless steel [G2 = 12,500 ksi] core (2) as shown in Figure and the allowable shear stress of core (2) is 60 ksi. Determine . The allowable shear stress of tube (1) is 27 ksi, (a) the allowable torque T that can be applied to the tube-and- core assembly. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced in a 10-in. length of the assembly by the allowable torque T. (1) т. FIGURE
2- The Tensile stress of AISI 1035 Cold-drawn steel is; (a) 550 MPa. (b) 500 MPa. (c) 450 MPa.
Maxinnun allowable stress for steel - 140 MPa Maxinnum allowable stress for ahuminum = 90 MPa Maxinnun allowable stress for brouze - 100 MPa Required: Maximun safe value of axial load P Aluminum A 400 mm Bronze A= 200 mm Steel A= 500 mm 2P 4P 2.5 m 2.0 m 1.5m
نقطة واحدد The ultimate tensile stress of gray cast iron is------than the * ultimate compressive stress same O less O more O more or less depending on other factors
7. ASTM suggests a tolerance of... percent to allow the variation in strength as a test of ....w. water. A. 12 В. 8 C. 10 D. 15 E. 16 F. None of them
25 mm PROBLEM 2.49 Brass core E- 105 GPa a- 20.9 x 10c The aluminum shell is fully bonded to the brass core and the assembly is unstressed at a temperature of 15°C. Considering only axial deformations, determine the stress in the aluminum when the temperature reaches 195°C. Aluminum shell E - 70 GPa a- 23.6 x 10rc 60 mm
The light rigid bar ABCD shown Is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. E200 CPa E1m 2.0 m 0.6m 1.5 m VP-20 KN Aluminum E-70 GPa A=900mm2 L-1.5 m What is the axial stress at steel rod in MPa?
M 1:A I. 3, O photo_2021-02-1.. -> 200 streas (MPa) 100 50 strain From the tensile stress-strain behavior fer the brass specimen d the diamcter is 12-8 mm Calculate the faibuding :- |- The Yield stress. 2-Modulus of elasticity. 3 - The Tensile strength . II
What is the axial stress in the bronze rod (in MPa)? 2m 3m 60 kN IS mm banzerod
A plate of 150 mm width and 20 mm thick is welded to another plate by fillet weld as shown in figure below. The size of the weld is 12 mm throughout. Compute the average shear stress produced in the weld for the full strength of the plate if the allowable stress is 150 N/mm². 70.72 mm T 50 mm 1 ㅅ 70.72 mm 150 mm- -150 mm -60 mm dia T 150 mm
Stress on an ique Plane under al Loading 12 Stress under eneral Loading onditions; Components f Stress 1.13 Design Considerations Review and Summary for Chapter 1 PROBLEMS REVIEW PROBLEMS COMPUTER PROBLEMS 2 Stress and Strain-Axial Loading 44°F Mostly cloudy AN DEVELOPMENT 2.12 A nylon thread is to be subjected to a 10-N tension. Knowing that E = 3.2 GPa, that the maximum allowable normal stress is 40 MPa, and that the length of the thread must not increase by more than 1%, determine the required diameter of the thread. 76 = 3 8 Search PAPER PERFORMANCE IN ALL 3.5
The 200-mm square aluminum block supports a compressive load of 300 kN. What is the normal stress acting on section a–a in MPa What is the shearing stress acting on section a–a in MPa The lapbelt assembly is to be subjected to a force of 800 N. What is the required thickness t in mm. of the belt if the allowable tensile stress for the material is 10 MPa?