H.W 1: Determine the memory location addressed by the following 8086 register combinations: (a) CS = 1000H and IP 2000H (b) DS = 2000H and SI = 1002H %3D %3D %3D
Q: Q2: Write down CX in hex (4M), CF (IM) after executing each instruction MOV CX, -SF7H SHL CX.I ADC…
A: The code is of the assembly language. The value of CX and CF after each instruction is as below:
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: The handwritten solution is given in the step-2.
Q: Q1) If BX=1000, DS=0200, SS=0100, CS=0300 and AL=EDH, for the following instruction: MOV [BX] +…
A: Given Values are:- BX= 1000, DS= 0200, SS=0100, CS=0300, AL=EDH The instruction is MOV [BX]+1234H,…
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: your answer is given below:
Q: Q5/ design an interfacing circuit for the memory to meet the following specification: 1-…
A: Answer:)
Q: Compute the binary representation of the following mips instruction: a) addi $s3, $t3, 7…
A: instruction: addi $s3, $t3, 7 Binary : 00100001011100110000000000000111
Q: Two similar processors A & B with F of 4 &S GHz and CPI of 0.2 & 0.3 respectively. Assume that the…
A: Dear Student, Here No of cycles in 1 second in A = 4GHz = 4 x 109 cycles per second. CPI of A(Cycles…
Q: Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H, the…
A: Given: We are given various registers with values stored in them. Register such as SS, DS, ES, CS,…
Q: Find the Addressing mode: Physical Address/es: Content of the destination:
A: Answers In the given instruction destination is EDX register and source data is the contents of…
Q: in 8086 Identify the addressing modes used for the source and destination operands, and then compute…
A: The answer to the question is given below:
Q: 6. A segment register =- for a physical address= 60000H and offset=D470H. 7. If an 8086 logical…
A: 6) Solution) 52B90H Explanation: Since Physical Address = Base Address + Offset Hence, the value of…
Q: Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H, the…
A: MOV 20.[DI], AL Here we are given that DS = 6000H Shifting left 20 times we will get 6000…
Q: Explain (in one to two lines) the function of the instruction MOV [BX], 2587H, if BX =2000H and DS…
A: The MOV instruction copies a byte or a word from source to destination. Both operands should be of…
Q: Q2) If BP=3000H, SI= 0022H, DS= 0200H. SS=0500H, BX=3471H, and CX=AB28H. Explain and draw the type…
A: BP = 3000HSI = 0022HDS = 0200HSS = 0500HBX = 3471HCX = AB28H Need to define type of addressing mode…
Q: 3) Assume SS=5000H, DS=600OH, ES=7000H, CS=9000H, BX=1000H, DI=2000H, SP=3000H, IP=4000H, SI=2000H,…
A: Given Instruction: MOV [DI + 3000H], AL. -> Here MOV means Move instruction. The content of…
Q: "uppose we have the instruction Load 500. Given that memory and register R1 contain the values…
A: Instruction Load is 500 So, Assuming R1 is implied in the indexed addressing mode. Immediate…
Q: XOR AL,[BP+DI] Select one: a. Register addressing mode b. OC. Indirect addressing mode d. Base plus…
A: The way of specifying the data that are to be operated by an instruction is known as addressing…
Q: he 64K single memory chip is used in total. Determine the number of lines in address bus including…
A: option(f) is the correct option.
Q: Suppose we have the instruction Load 500. Given that memory and register R1 con tain the values…
A: In immediate addressing mode, the value present is the operand itself. So here A = 500 In direct…
Q: Note: Identical answers are neglected Q1: Identify the addressing mode for the following…
A: INTRODUCTION : The physical address is a memory address translated to a binary number by the address…
Q: Ques. if the number of general purpose registers (e.g. $t0, $a0, etc.) was increased to 64, then the…
A: The answer is True.
Q: Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H, the…
A: Given Instruction: MOV [DI + 3000H], AL. -> Here MOV means Move instruction. The content of…
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: Here, I have to find addressing mode, physical address and content of the destination.
Q: Column X 1. MOV A, #25H 2. MOV R6, A 3. MOV 56H, A 4. MOV @RO, A 5. MOVC A, @A+DPTR Column Y A.…
A:
Q: 3) Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=100OH, DI=2000H, BP=3000H, IP=4000H, SI=2000H,…
A: Finding the physical address MOV 30.[SI], AL Here we are given that DS = 6000H Shifting left 20…
Q: Problem 4: Give a block diagram for a 8M x 32 memory using 512K x 8 memory
A:
Q: H\W: Assuming the SP-1236. Ax-2486. DI= 85c2 and Dx-5f93, show the content of the stack and the…
A: Given Data: SP = 1236H AX = 2486H DI = 85C2H DX = 5F93H ADD AX,SP: Add values of AX and SP and…
Q: What MIPS instruction format(field) is used for the following: -Addi $s3,$s3,4 -Sub…
A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: The answer as follows
Q: Computer Science Write down the register transfer notation for the following assembly language code…
A: Answer: I have given answered in the handwritten format
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: given, the contents of the register SI=AECDH. convert, AECDH from hexadecimal to decimal. 160 * 13 +…
Q: 2. Identify the addressing mode for the following: a. add $8, $9, $10 b. addi $8, $9, 100 C. lw $8,…
A: Addressing mode is expression which is used for addressing mode in the way that the operand of an…
Q: 9. Write instruction sequence to add Ox0A to Ox222 - 0X22A by a. Direct addressing mode b. Indirect…
A: Below i have given instruction for both the meathod:
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: Given The answer is given below.
Q: 3) Write a ALP for 8086 to exchange the content of AL and AH registers without using XCHG…
A: We can utilize BL register to trade the worth of AL and AH registers , the code for the equivalent…
Q: Identify if possible the type of addressing modes for the following instructions. 1. MOV BX, [DI +…
A: The different modes for specifying the operand address in the instructions it is referred as…
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: your answer is given below:
Q: 2. Suppose that DS = 1300H, SS = 1400H, BP = 1500H, and SI = 0100H. Identify the addressing modes…
A: Solution (a) MOV EAX,[BP+200H] (b) MOV AL,[BP+SI-200H]
Q: a) For the following fragment of 8086 program, show the content of register AX after each…
A: contentent of AX register is AX=AH+AL
Q: Determine the memory location addressed by the following real mode 80286 register combinations: Show…
A:
Q: .MOV R5 #1FH ii).MOV @R1 A iii) MOV R1,05 iv) MOVCA,A+DPTR V) MOV R2 A
A: Function of MOV is to move memory it takes operands 1,2 (i) MOV R5 #1FH : Load 1FH into R5 Now…
Q: B2.JPG MOV SP,[BP+DI+ACBAH] ВJPG PHY. ADD| С6079H АСH C607AH BDH С607вн | СЕН C607CH| F1H C607DH 02H…
A: We need to find required addresses for given assembly code.
Q: Write the MIPS code of the below given C code. Also identify type of each instruction and encode all…
A: Given C code : A[3] = 7*X+9*Y+100;X = 12*A[A[2]]+21*Y-30;Y = A[X]+A[X+2];
Q: b) Given that the crystal frequency of 8051 Microcontroller is 11.059 megahertz, and one machine…
A: crystal frequency is 11.059 MHZ
Q: Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H, the…
A: Given: We are given various registers with values stored in them. Register such as SS, DS, ES, CS,…
Q: Assume the following are given CS=9345H, DS=2835H, SS=9326H, ES=1955H, IP=2233H, BX=C235H, SI=3D32H,…
A: Actually, given information is: CS=9345H, DS=2835H, SS=9326H, ES=1955H, IP=2233H, BX=C235H,…
Q: Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es.…
A: Addressing mode , of physical address and content of destination: MOV[BX],BX copy BX contents to…
Q: 3) Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H,…
A: Concept Given: We are given various registers with values stored in them. Register such as SS, DS,…
Q: Q1) If BX=1000, DS=0200, SS=0100, CS=0300 and AL=EDH, for the following instruction: MOV [BX] +…
A: Given, BX =1000 DS =0200 SS =0100 CS =0300 AL =EDH Instruction = MOV [BX]+1234H,AL Physical…
Q: If BX=1000, DS=0200, SS=0100, CS=0300 and AL=EDH, for the following instruction: MOV [BX] + 1234H,…
A: Answer: It is a base addressing mode. Effective address of the operand obtained by adding direct or…
Step by step
Solved in 2 steps
- a. Find the address accessed by each of the following instructions. If DS = 0100H, BX= 0120H, DATA = 0140H, and SI = 0050H and real mode operation:1. MOV DATA[SI], ECX2. MOV BL, [ BX+SI]b. Descriptor contains a base address of 00260000H, a limit of 00110H, and G = 1,determine starting and ending locations are addressed by the descriptor for aCore2.Match segment and offsetregisters and determine their correspondingactual memory location addressed of the following real mode 80286 segment registers given below. Segment Register Effective Address 1. CS = 2010H 2. DS = 2100OH 3. ES = AB80H 4. SS = 1234H 5. DS = B20FH When: a. DI = 2000H d. IP = ABCDH b. BX = 100AH e. BP = 12FFH c. SP = 3A00H Type the address in uppercase. Do not forget to append H to each addresses. 1. EA: 2. EA: 3. EA: 4. EA:The 8-bit register AR, BR, CR, and DR initially have the following values: [5]AR = 11010110; BR = 11100111; CR = 10110001; DR = 10111010Determine the 8-bit values in each register after the execution of the following sequence of microoperations.AR AR + BR Add BR + ARCR CR AND DR, BR BR + 1 AND DR to CR, Increment BRAR AR - CR Subtract CR from AR
- The 8-bit register AR, BR, CR, and DR initially have the following values: [5]AR = 11010010; BR = 11111111; CR = 10101001; DR = 10101010Determine the 8-bit values in each register after the execution of the following sequence ofmicrooperations.AR AR + BR Add BR + ARCR CR AND DR, BR BR + 1 AND DR to CR, Increment BRAR AR - CR Subtract CR from ARIn max mode, control bus signal SO,S1 and S2 are sent out in 1 point form * Shared Decoded Unshared Encoded The clock rate of microprocessor 8086 is 1 point FFFF0H 00000H FFFFFH 0000FH To design a 8086 memory system consisting of 1 Mbytes must we have * 1 point 32 number of 64K× 8 memory. 64 number of 64K× 8 memory. 64 number of 32K× 8 memory. 32 mumber of 32K× 8 memory.02:- (A) Find the phicycal address if (BP) = 0100H, (SI) = 0200H , (SS) = 2000H and a displacement of 10H, of the instruction MOV AL. (BP+S+10H]. Which the name of Addressing Modes? 02:- (B) Find the result of the following: 1111-iIH+110010111011B 03: Write a piece of code to find the number of negative integers in an array of size 1024 bytes contain signed numbers stored at addresses starting at 21000H, store the result in a location 51000H
- is stored in the memory starting 2- The ISR address of interrupt number at address (0039CH). 3- In the instruction: (MOV AL,[3AFH]), data is transferred to 8086Mp over data clock cycles. lines: using 4- In the instruction: (MOVAX,[5BC2H]), data is transferred to 8086Mp over data lines: clock cycles. using12. In a BSL instruction block B3:10 holds the word 8ECOH, and the bit starting address is B3:0/15. What word is held in the B3:10 after one low-to-high transition signals are sent to this BSL instruction block's input?In the following indexed addressing mode instruction, MOV 5(R1), LOC the effective address is А. EA = [R1] EA = 5+R1 C. EA = 5+[R1] D. EA= R1 B.
- 5. If the state of 8086 is as follows : (SI) = 0500 H (DS: 0500 H) = 00 H (DS: 0501 H) = 10 H Execute the each instruction below: a) JMP 10 H b) JMP 1000 HQ2- Write a program in assembly language for the 8085 microprocessor to receive one byte of data via the SID and store it at the memory address (3000H to 3009H) using a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When receive the required bytes, you must adhere to the following: The bits of two high bits will be received at the beginning of the reception(start bits 1 1 ), after that the data bits will be received, after that the low bit of the stop bit will be received (stop bit 0 ). The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay timeQ1- Write a program in assembly language for the 8085 microprocessor to receive 10 bytes of data via the SID and store it at the memory address (3000H to 3009H) using a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When you receive each byte of the required bytes, you must adhere to the following: The bits of two high bits will be received at the beginning of the reception (start bits), after that the data bits will be received, after that the low bit of the stop bit will be received (stop bit). The following flowchart will help you, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes The solution must be integrated and include the calculation of the baudrate delay time Of+CD!HID+[00 Yes SIDATA Read SID Start Bit? Wait for Half-Bit Time Set up Bit Counter Wait Bit Time Read SID Save Bit Decrement Bit Counter All Bits Received? Add Bit to Previous Bits Go Back to Get Next Bit Return IMUNI