grounding and bonding requirements 17. Which of the following is effective when it comes to establishing a bonding connection between a fitting or a raceway and an enclosure? A. Meter enclosures B. Bonded bushings C. Bonding wedge D. Threaded hubs 18. Which of the following is the first line of defense for a premises wiring system served by a grounded utility source? A. The system grounding connection B. The pad-mounted transformer C. The load side of the service point D. The service equipment enclosure

grounding and bonding requirements 17. Which of the following is effective when it comes to establishing a bonding connection between a fitting or a raceway and an enclosure? A. Meter enclosures B. Bonded bushings C. Bonding wedge D. Threaded hubs 18. Which of the following is the first line of defense for a premises wiring system served by a grounded utility source? A. The system grounding connection B. The pad-mounted transformer C. The load side of the service point D. The service equipment enclosure

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter16: Installation Of Heating, Cooling, And Refrigeration Systems

Section: Chapter Questions

Problem 13RQ

See similar textbooks

Similar questions

If required, what type of diagram must indicate the calculated load, demand factors, conductor type and size, and area served? A. A transformer configuration B. A branch circuit mapC. An installation planD. A feeder diagram
5.a. The aging of transformer insulationA. increases as the temperature increases.B. does not affect the transformer life.C. is not affected by the temperature.D. decreases as the temperature increases.5.b. Excessive power-transformer noise at the start of operation is most likely caused byA. an open feeder switch.B. a loose brace.C. a defective radiator.D. an open load fuse.
1 .Which one of the following component is the heart of the excitation system?. a. Resistor B. Voltage Transformer C. Current Transformer D. Voltage Regulator
1. Explain how a fuse saving scheme is performed using a recloser. ii. What is a sectionalizer and how does it work in coordination with a recloser? 111. Explain the effect of the magnetizing inrush current on transformer protection. iv. Explain how transformer core faults, inter-turn faults and oil leaks be detected.
Larger conductors should be used for long runs to minimize the? A. Current B. Voltage drop c. Transformer retio d. Interrupt rating
Distribution transformers are generally protected from damage due to excessive internal temperatures, by the operation of a A. lightning arrester. B. surge diverter. C. flexible baffle. D. circuit breaker.
7.a. Excessive power-transformer noise at the start of operation is most likely caused byA. an open feeder switch.B. a loose brace.C. an open load fuse.7.b. A type of transformer assembly for use with load tap changers is theA. constant-current transformer.B. iron-core reactor..C. air-insulated reactor.
A transformer has a turns ratio of 3:7 and is supplied with 240V. When the primary current is23A, Calculatei. Secondary voltage.ii. Secondary current.iii. Transformer rating.iv. Voltage regulation when secondary full load voltage is 500V.
LOCAL 5652 UNION LABEL USW UNITED STEELWORKERS 6. Which one of the following types of construction is used for potential transformers? A. Window-type B. Wound-type C. Bushing-type D. Bar-type
UNITED STEELWORKERS 8. The effect of high-frequency discharges on current transformers used in high-voltage circuits is reduced by use of a A. porcelain insulator bushing B. grounding connection C. high-voltage fuse D. bypass protector
In a typical unit substation the majority of the connections to ground are made in the_. A. High- voltage section B. Transformer section C. low- voltage section D. None of the above.
The short circuit test is used to measure the __________________________________ of the transformer. (a) Brush loss (b) Friction loss (c) Iron loss (d) Copper loss