Given the full-wave rectifier circuit shown below and given that the diode is made up of Silicon and the diode internal resistance, rD, is 10 Q, answer the following: A. Which diode turns ON due to a positive half cycle AC signal input? B. Find the peak current Im (in mA) flowing through the resistor RL. C. Find the peak voltage Vm (in V) across the resistor RL.

Given the full-wave rectifier circuit shown below and given that the diode is made up of Silicon and the diode internal resistance, rD, is 10 Q, answer the following: A. Which diode turns ON due to a positive half cycle AC signal input? B. Find the peak current Im (in mA) flowing through the resistor RL. C. Find the peak voltage Vm (in V) across the resistor RL.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
Given the clamper circuit below, assume that the value of R and C are large enough sothe voltage across the capacitor does not change significantly during the interval of time.a. Using the simplified diode model, simulate the action of the circuit when the Silicon diode isin forward and reverse bias condition and measure the corresponding output voltage.b. Draw the complete output waveform of the circuit
A silicon diode with a forward resistance of 100 is connected in series with a 5000 resistor. If an a.c voltage of 20V peak is connected across the series combination of the diode and the resistor what will be the peak value of the current through the diode and the peak output voltage? What will be the peak value of the current through the diode and the peak output voltage if the diode were ideal?
4. If the diode is open in the circuit, the load voltage is? 5. If the resistor is ungrounded in the circuit, the voltage measured with a DMM between the top of the resistor and ground is closest to? 6. The load voltage measures 12 V in the circuit. The trouble may be? 7. Using the third approximation in the circuit, how low must R, be before the diode's bulk resistance must be considered? + Vs RL 1 k2 12 V Figure
Sketch i against v to scale for the circuit. The diodes are typycal small-signal silicon devices 300 K. The reverse-breakdown voltages of the diodes are shown. Assume .6 V for all diodes (including Zenners) in the forward-bias region.
3) Demonstrate clipping of negative waves with an inverted diode in the output. A circuit which removes the peak of a waveform is known as a clipper. Show a negative clipper. Produce a schematic diagram with LTspice schematic capture program. During the positive half cycle of the 5 V peak input, the diode is reversed biased. The diode does not conduct. It is as if the diode were not there. Show the positive half cycle is unchanged at the output V(2). Show the output positive peaks overlays the input sinewave V(1). Use in the LTSPICE display module, the command "plot v(1)+1)" accomplishes this. Voltage values: Resistor valuse: 1 ΚΩ DC offset: 0 V Amplitude: 5 V Freq: 1 KHz
Determine the small signal resistance of the diode by assuming a constant voltage drop model for the diode. Assume that the thermal voltage is 25mV.
Find the value of RI in the circuit shown below, assume Ipz is twice Ipi. The diodes have constant voltage drop of 0.7v for silicone and 0.3v for germanium