Given :take P1 = 10 KPa  Turbine entry conditions = 16 MPa and 600 oC(Degrees Celsius) Turbine output=5 MPa Phase state saturated water at the heat exchanger outlet and heat exchanger efficiency 85% Required power for district heating = 1100 kW Turbine power= 5500 kW Question: What is the value of my ???

Q: An experimental gas turbine engine is under development to increase its mechanical efficiency. It…

A:

Q: Concentric tube heat exchanger (tubular or tube in tube) is used for a large industrial gas turbine.…

A: Given :- Concentric tube heat exchanger (tubular or tube in tube) is used for a large industrial gas…

Q: 3.4 Find the flow rate of water through the Problem Set 3 system shown for the turbine to produce 20…

A: Given Data The power produced is: P=20 kW The diameter of the ball is: d=75 cm The height of the…

Q: Ke'd TS+1 Considering a change in inlet temperature show why a 1st order model for a CSTR and a dead…

A: Given in Question :- R=radius K= conductivity  C= specific heat

Q: 1. Given: A pipeline connecting a reservoir with a pump. - Properties of the pipeline: L= 450 m; D=…

A: Friction loss is the amount of energy lost by your piping system as a result of fluids encountering…

Q: What is the engine stroke (in mm) required for good volumetric efficiency for an engine with two…

A:

Q: #2: the condenser of Geothermal Heat Pump will be cooled by A pipe with meter 3 cm buried in a soil…

A:

Q: A system requires a flow rate of 225 gpm (14.2 L/s) and a head of 149 ft (45 m). (a) Seles pump from…

A:

Q: Q2: Water is flow by a rate = (V0.3 × your code number) | 20) m'/s, the water is still stable due to…

A:

Q: Eg.5 300 m VA.Jmfs(maker) L00

A:

Q: 1. Given: A pipeline connecting a reservoir with a pump. Properties of the pipeline: L= 450 m; D=…

A: Given Data ; L=450 M D=0.4M ∈=0.5mm Q=380l/s we know that  Q=AV V=Q/A =380×10-3π4×0.42 =3.02 M/sec

Q: If a dom atydiatic tubing find the requiedtaqe e A shaft Conectad tthe tobin ananmer is being-sitet…

A: The torque required on the shaft is 2054.35 N•m.

Q: mpute the volumetric flow rate (GPM) of ethanol at 77°F that would occur given the above nditions.…

A: In the question, there are losses in the pipe due to - 1. Pipe firction 2. Pipe bending 3. Half…

Q: A water pump is used to pump water from one large reservoir to another large reservoir that is at…

A:

Q: Water is retained in a small mountain lake whose surface is 280 ft above the inlet to the turbines…

A: Bernoulli's theorem is used in fluid dynamics and gives the relationship between the pressure,…

Q: What is the engine bore (in mm) required for good volumetric efficiency for an engine with two inlet…

A:

Q: he date for a certain installation are as follows Net Head = 454 m, BP = 57,200 bkw, n = 750 rpm,…

A: Given:H=454 mP=57200 KWN=750 rpm

Q: A boiler house has natural draught chimney of 20 m height. Flue gases are at temperature of 380°C…

A:

Q: tube (d=6omm) a rate ot ool Rals wr Watel enters a temp. of 20c . A constant heat flusx of 2000 wini…

A:

Q: 03: There are three connected pipes (38 m length of 5 cm pipe diameter),. (23 m length of 15 em pipe…

A: The relation is used to determine the power  PT=ρgQ(h-hL) Here,  PT is the power extracted by the…

Q: What is the engine bore (in mm) required for good volumetric efficiency for an engine with two inlet…

A: An engine is a machine that translates energy from fuel to mechanical energy that creates movement.…

Q: (b) A cast iron piping system deliver water at 20°C from a close tank, T1 to an open tank, T2 as…

A:

Q: 18. A pump delivers water to a differential elevation of HB - H₁ = 40 ft. Diame- ter of the suction…

A:

Q: Concentric tube heat exchanger (tubular or tube in tube) is used for a large industrial gas turbine.…

A: A concentric tube heat exchanger (tubular or tube in tube) is used for a large industrial gas…

Q: Q.5 A pump circulates water through a closed pipe network connecting a water heater and a heating…

A:

Q: HW2: A hydroelectric power plant built for a design head of Hn=12.5 m should develop a rated output…

A: Given: Head of the plant→Hn=12.5 m Rated power→P=12000 hp=8952 KW Because efficiency→e=0.90 Density…

Q: 3. The following data are given for a U-tube steam generator. Tube mass flow rate m =70E6 lbm/h,…

A: Head represents by the body force is known as hydrostatic head because of gravity when forced…

Q: all separated air in order t = transfer rate e added to air sfer coefficie is 255 W/m - is 57 W/m K

A:

Q: Thot Tout-? mnot 75°C %3D mcold Tcold = 18°C Hot and cold stream of water are mixing together as…

A:

Q: A) A large Francis turbine having the following specification: diameter of runner outside (1.5m) and…

A: d0=1.5 m , b=.135 mP=16 Mw ,H=260 mN=600 rpm .Q=7m3secvf2=16 msec and vw2=0 width to diameter ratio…

Q: A reaction type hydro-electric plant use a 95% efficiency generator to produce its rated output of…

A: Given data: ηgen=95%Pout=20 MWPloss=2.5 MWH=30 mh=5 m Need to determine the power by the turbine ,…

Q: 7. A hydro-electric power station is supplied from a catchment area of 480 km² with an annual…

A:

Q: Q.8 A turbine is working under a head of 200 m. The power developed by the turbine is 100 kW and…

A: Given Data P=100 kW H=200 m Q=0.125 m3/s

Q: The catchment area for the reservoir of a hydro-electric power plant is 14 x 108 sq m having an…

A:

Q: A hydraulic reaction turbine working under a head of 16 m develops 640 kW of power. What is the unit…

A: The Given values are: Head H=16 mPower P=640 kW

Q: Täsk A dam supplies water for a community as shown in Fig. 1. Also, a turbine is used before the…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: A pump is used to raise water from open tank to another one. If the pipe diameter is 300 mm, Length…

A:

Q: In figure raws a on ol a 2. In the system storage tank through a pipe with cross sectional area…

A: To Find : The work done by the pump per unit mass of water Given :  The velocity of suction pipe is…

Q: 1. To model power production in a traditional hydroelectricity unit, we can use the below schematic…

A: Given: The density of water, ρ = 998 kg/m^3 The dynamic viscosity, µ = 0.001 kg/ms The tank…

Q: 1. Given the following parameters, design a vertical heater-treater: Qo = 5,000 bopd API = 36 inlet…

A: We will answer the first question since the exact one was not specified. Please submit a new…

Q: Suppose that the pump of Fig.  is run at 1100 r/minagainst a pressure rise of 210 bar. (a) Using the…

A: Given:Pump speed,n=1100r/minPressure rise,∆P=210 bar

Q: An impulse turbine operating at a net head of 2000 ft uses a Pelton wheel of diameter 12 ft and a…

A: GivenH=2000ft=609.6md=12ft=3.6576mA=5in2=0.00064516 m2Cv=0.94deflected angle φ=165o

Q: A hydroelectric station operates under a mean head of 30 m. The reservoir employed has a catchment…

A:

Q: Table Q3 is given to collect the temperature of hot and cold water at the inlet and o in the…

A: 1. Temperature distribution diagram

Q: In Fig. the pipe entrance is sharp-edged. If the fl ow rateis 0.004 m3/s, what power, in W, is…

A: Given Data: The flow rate of water is, Q=0.004 m3/s. The head of water above the turbine axis is,…

Q: A large hydropower station has a head of 50 m. The rated power of pla installed is 200 MW. Find: 1-…

A: Given head of the hydropower station (h)=50 mRated capacity of power plant=200 MW

Q: watl enters a tube (d=6omm) a rate of o.ol Kals with temp. of 2öc3. A constant heat flux of 200 Wini…

A: Given data:-diameter of tube, d=60mmmass flow rate, m˙=0.01kgInlet temperature of water,…

Q: Water at 20°C is flowing in a serial connected piping network with 270 L/min. Pipes have been made…

A: