For the circuit shown, for what range of Vi(t) will the diode be of 8k 1V Vi() 2k2 Vout Vk-0.7V O a. Vilt) less than 2.7V O b. Vilt) less than - 4.6V. O c. Vi(t) greater than 4.6V. O d. Vi(t) less than 8.5V. O e. None of the listed range O f. Vilt) less than 1.7V O Q. Vi(t) greater than 3.7V O h. Vilt) less than 3.7V

For the circuit shown, for what range of Vi(t) will the diode be of 8k 1V Vi() 2k2 Vout Vk-0.7V O a. Vilt) less than 2.7V O b. Vilt) less than - 4.6V. O c. Vi(t) greater than 4.6V. O d. Vi(t) less than 8.5V. O e. None of the listed range O f. Vilt) less than 1.7V O Q. Vi(t) greater than 3.7V O h. Vilt) less than 3.7V

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
Determine the state of diode for the circuit shown and find ID, VD. Assume simplified model for the diode. 4k02 2V 1k02. Off, 0.00mA, 0.4V O Off, -0.005mA, 0.0v On, 0.48mA, 0.6v On, 0.55mA, 0.7v Option 5
u= 6sinot V. V. For the circuit of Figure, we have known E=3V, Use the ideal diode model to analyze the circuit and draw the waveform of the output voltage. 6V cot Uj E
In reference to the output waveform below and using ideal diode model: Vout +7.5V -3.5V a. Analyze the behavior of the circuit and fill up the table below. Vin Diode state Vout (FB or RB) +6V OV -3V -6V b. Draw the clipper circuit that will produce the given output waveform.
For the circuit shown below, sketch to scale the output V waveform and draw the transfer characteristic (V versus Vi), Assume the diodes are ideal.
For the circuit in the figure, let V input = 8V, Ri = 12ohms, RL = 10ohms, and VZ = 3.3V. Determine the voltages and currents of the resistors and the current of the zener diode.
For the an input waveform of -7.89 V to the given circuit, what is the peak value (in V) of the output waveform? Use Germanium diode.
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
For the diodes used , at what Voltage (VD) does condection stars .
B. For the circuit shown below, assume that the zener diode has Vz-3.3V and rz=092 when reverse biased, and has a 0.7V drop when forward biased. Fill the following table for values of Vo for different values of input voltage Vi. R1 Vi Vi -8V OV 8V 1k 5V N V2 R21k Vo Vo
In the clamping circuit below, assume the diode has Von-0.7V and V₁ is a sinusoidal wave with a peak-to-peak amplitude of 10V. How much is the maximum value of the output voltage signal (Vmax)? And how much will it be if we set V₂=2V? Input V1 C1 0.1e-6 9.3 V and 7.3 V 9.3 V and 11.3 V 11.3 V and 7.3 V O 7.3 V and 12.0 V O 12.0 V and 7.3 V Output D1 1N4148 .tran 30-3 V2 0 Vmax V(output) 0.0ms putput MAN Input 0.6ms 1.2ms V(input) 1.8ms 2.4ms 3.0ms
For the circuit shown in the Figure, if the diodes are silicon diodes with VD(on)=0.7 V, and VIn=50 sin wt V, V1 =7 V and V2 =13 V, then the value of VOUT (p-p) is: R1 D, D2 VIN VOUT vi E v2= Ca. 19.4 V Ob. 17.4 V Cc. 15.4 V Cd. 21.4 V