Find the volume of the propane tank. Assume IPS units, set before you begin to sketch the part.. The material is AISI Steel 1020. A = 9.75 Hint: Draw just half of the front view of the tank, then revolve that 360°. Diameter dimensions are the full width of an object, so if you're only drawing half, use half the diameter.

Find the volume of the propane tank. Assume IPS units, set before you begin to sketch the part.. The material is AISI Steel 1020. A = 9.75 Hint: Draw just half of the front view of the tank, then revolve that 360°. Diameter dimensions are the full width of an object, so if you're only drawing half, use half the diameter.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 9RQ: A dimension listed on an engineering drawing is known as the _______ _______.

See similar textbooks

Similar questions

Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your answer should have 0 decimal places needed. Ex: 76,440 10 - 30 B
Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A = 65 B = 43 A 40 B-30 10 30 40 B
Ixo and Iyo of a quarter circle with a diameter of 50cm (Answer format: Ixo= , Iyo=)
Build the following part and report the volume in units cubed. A = 48 B = 51 R20 R10 B 30 50 2X R10 R20 Ø20 A 10 TYP DESIGN ERICS DRAWING TITLE
52 What is the distance between the center of circle A and the corner at B? R3 03 Start a new drawing based on Mech-Millimeters.dwt. Draw the object shown in Figure A-1, starting with the center of the Ø3 circle at point 5,5. Draw only the object, not the dimensions and then answer the following questions: O 186794 198628 193132 171870 R1.0 TYP. 18 8 2 2 1 10
View Image. Show complete and detailed solution. Please write legibly. Answer: 30 N
Mechanical Advantage Classwork Directions: Show all work with the following steps... 1.Write the equation. 2.Fill in the equation. 3.Solve. To find the Mechanical Advantage of ANY simple machine when given the force, use MA = R/E. An Effort force of 30N is applied to a screwdriver to pry the lid off of a can of paint. The screwdriver applies 90N of force to the lid. What is the MA of the screwdriver? 1. MA =
Five points are equally spaced on a circle. A five-pointed star (pentagram) is formed by joining nonconsecutive points two at a time. What is the degree measure of an arc determined by two consecutive points?
Please solve this question with detailing
A dog is pulling on his lead at an angle of 39 degrees with a force of 50 Newtons. What is the force downward? Newtons. What is the force horizontally? Newtons. Note: You can type the trig in the answer box for all these problems. For example if the answer is 50cos(10), you can just type that into the answer box. To get inverse trig functions type arcsin, arccos or arctan.
Build the following part. Report the mass in pounds. Assume all dimensions are in inches. The material is Vanadium. (Located in the "Other Metals" folder in the material properties.) A = 1.72 B = 1.4 2.40 1.20 T .75 TYP 1.20 TYP .70 -1.00 TYP A A A+3.25 R.35 TYP -R.65 TYP CBORE FOR 5/16 HEX HEAD BOLT Ø.332 THRU ALL LØ813 V 235 .10- SECTION A-A 23. B B+1
solve question completly