Example 1 Water enters the basement through a pipe r1=2 cm in radius at an absolute pressure of 3 atm. A hose with a r2=0.5 cm radius is used to water plants 10 m above the basement. Find the speed of water as it leaves the hose (v2)? & (V1) hose r= 0.5cm p= 3atm v =? y: = 10m/ Noting: pwater=1000kg.m-3 Pipe r= 2cm p= 3atm v=? y1 =0 basment

Example 1 Water enters the basement through a pipe r1=2 cm in radius at an absolute pressure of 3 atm. A hose with a r2=0.5 cm radius is used to water plants 10 m above the basement. Find the speed of water as it leaves the hose (v2)? & (V1) hose r= 0.5cm p= 3atm v =? y: = 10m/ Noting: pwater=1000kg.m-3 Pipe r= 2cm p= 3atm v=? y1 =0 basment

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
(95 7 A U U O b vol1:EA محو التحدید Q6: Water enters a horizontal pipe with a rectangular cross section at a speed of 1 m/s. The width of the pipe remains constant but the height decreases. Twenty meters from the entrance, the height is half of what it is at the entrance. If the water pressure at the entrance is 3000 Pa. what is the pressure 20 m ?downstream 1.5 Pa 15 Pa 150 Pa 0.15 Pa 1500 Pa Note: Solve each question in a separate sheet of paper with your name. Take pictures and upload them with your form. Then submit your å lla K la work
A venturi meter, shown in Fig. designed constriction whose pressure difference is a mea- sure of the flow rate in a pipe. Using Bernoulli's equation for steady incompressible flow with no losses, show that the flow rate Q is related to the manometer reading h by is a carefully 2gh(PM – p). A2 VT- (D/D;)4 where py is the density of the manometer fluid. 2
Q2- Water density =1000 kg/m and viscosity is 0.001 Ns/m², is pumped between two reservoirs at 0.2m/s through a 400 m of 8 cm diameter Cast Iron pipe and several minor losses as shown in the figure. Compute the pump power required in kW. Use the last one digit of your ID number for Z1 level in meter. Screwed Z2= 50 m regular 90° elbow Sharp exit Z;= ID m Sharp entrance Half-open gate valve `bend radius Pump Open globe valve 8 cm diameter
Q1. Two pumps with 105.4 cm in diameters characteristics shown in figure below are used in paralel to pump water to the system. Neglecting local losses, calculate total flow rate and pump power. (a) n= 710 d/dak 120 7.5 80m ENPY (2) 6. 105 - 105.4 cm çap S N 4.5 3 90 96.52 cm çap 88% 86% 75 - 88.9 cm çap S4% (1) bom 60 1100 kW 45 750 kW 30 0.25 0.50 0.75 1.00 1.25 1.50 1.75 Debi m/s Note: Pipe is cast iron with 0.6 m in diamater and 1.6 km in length. Fluid is water with density 1000 kg/m³ . ENPY m %68 900 kW
A water supplying pipe of diameter 14 cm, is used to pump the water to the house in the Tanuf hill at the height of 60 m above the ground. The flowrate at the end of the pipe is 180 lit/s. The pressure gauge is connected at the inlet of the pipe in the ground and measured as 35.5 N/cm2. Find the following: (i) The kinetic energy per unit weight at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe entry (unit in m)
Water (p 1.96- slug) flows through the pipe system below. Data is given below: = ft³ Pipe 1: V₁=1.8 ft, D₁ =2.4 inches, p₁ =24.9 psi Pipe 2: V₂=1.4 t, D₂=1.9 inches 2 Pipe 3: D3=0.7 inches Assume no energy is lost to friction. Find the pressure p3. Report your answer in psi. V₂ V₁ P₁ D₁ D₂ P2 D3₁ V3 P3
A pipe of diameter 12 cm, is used to pump the water to the house in the Hamra hill at the height of 60 m than the ground. The discharge at the end of the pipe is 200 lit/s. The pressure gauge is fitted at the entry of the pipe in the ground is 34 N/cm?. Find the following: (i) The velocity head at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe inlet (unit in m) (Enter only the values by referring to the units given in brackets & DO NOT write the unit & do not send the handwritten answers to my mail id...) velocity head at the entry of the pipe is = (unit in m) pressure head at inlet = (unit in m) Total available energy per unit weight of the water at inlet of the pipe
Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 12 in. The atmospheric pressure is 14.7 Ibf/in?, the specific volume of water is 0.01604 ft/lb, and the acceleration of gravity is g = 32.0 ft/s?. Patm = 14.7 Ibr/in.? g = 32.0 ft/s² Water v = 0.01604 ft/lb Determine the difference in pressure between points a and b, in Ibf/in2?. Does the pressure increase or decrease from point a to point b? Sten 1
2. Suppose the pump of Fig. P14-23 is operating at efficient condition. The pipe diameter after the pump is "X" cm and pipe diameter before the pump is "Y" diameter. The friction losses along the pipe are negligible (no need to use Darcy Equation). But there are minor losses in the system. They are as follows; the sharp inlet is 0.50 m of water, each valve has a loss of 2.4 m of water, and each of the three elbows has a loss of 0.90 m of water. The contraction at the exit reduces the diameter by a factor of 0.60 (60% of the pipe diameter(after the pump)), and the loss of the contraction is 0.15 m of water. The volume flow rate is "K" Lpm. Density= 990kg/m. dynamic viscosity=1.002 x103 kg/m-s. Z1-Z2="L". The kinetic energy correction factor is 1. Determine (a) Required Head, (b) Required pump power (water Hp), (c) Reynolds number at the exit. V = 0 Reservoir Pump Given for Problem 2 X Y K L 1.8 148 6
Problem Set No. 1 1. A 200 kg chunk of lead falls from a height of 30 m and smashes into a rigid concrete floor. Calculate the increase in the internal energy AU (MJ), assuming that no energy is transferred as heat from the lead. 2. Assess the capabilities of a hydroelectric power plant from the following field data: Estimated water flow rate, 40 m³/s River inlet at 1 atm, 10 °C Discharge at 1 atm, 10.2 °C, 200 m below the intake 3. How much energy transfer as heat is required to evaporate completely 1 kg of nitrogen for a constant pressure process, with T = 89.5 K? 4. One kg of CO₂ is heated in a 0.5 m³ vessel from -18 °C to 93 °C. Determine the initial and final states, and the amount of energy transfer as heat to the CO2. 5. The condensate pump on the Navaho power plant raises the water pressure from 3.5 in of mercury to 390 psia at a flow rate of 5,100 gal/min. If the pump isentropic efficiency is 0.8, calculate the power required in hp. 6. Calculate the thermal efficiency of a…
Q3/ Water is flowing upwards in an inclined homogeneous pipe from point No. (1) to point No. (2). The following data is available:- 1- Length of pipe, L= 1400 (m). 2- Diameter of pipe, d= 0.25 (m). 3- Elevation of point No. (1) is 15 (m) above the Reference line and elevation of point No. (2) is 30 (m) above the Reference line. 4- Piezometric head at point No. (1), hi= 61.16 ( m of water height). 5- Piezometric head at point No. (2), h2= 20.39 (m of water height). 6- Friction coefficient f=0.02 and hL=zero Find: 1- Head loss of water flow in the pipe from point No.(1) to point No.(2) due to friction hf. 2- Water flow rate Q and flow velocity v in the pipe. Draw the H.G.L. of water flow in the pipe from point No. (1) to point No. (2).