Estimate the height which water will rise in a capillary tube 12mm diameter. Use surface tension = 0.0728 N/m and gamma = 9810 N/m^3
Q: Can you please help in that with proper steps?
A: To determine the values of the drained shear strength parameters c' and Φ' for the silty-clay, we…
Q: Question: Given: a = 0.4 m b=0.1 m F₁ = 800 kN F₂ = 915 kN M₁ = 400 kNm •A 0.7 m 1 m 1) Find the…
A:
Q: How much weight can a 4-meter-tall steel (E = 200 GPa) column of cross section 20 x 60 mm with one…
A: Given data -Modulus of elasticity E = 200 GPaLength L= 4 mColumn cross section ( b x h ) = 20 x 60…
Q: Inclined U-tube manometer: (1)- Figure 2.12 John Wiley & Sons, Inc. All rights reserved. -(2) PA= P…
A:
Q: Calculate the task according to the instructions. Show formulas in Excel for each point. Put…
A: The objective of the question is to evaluate the profitability of an investment in a new enterprise…
Q: overhang beam. 20 kN 20 kN/m -2 m C
A: Consider the given beam :Support reactions are :using static equilibrium conditions,∑MB=0⇒ Ay × 4 +…
Q: A Masonary Dam &m high, 1.5m wide at the top and 5m wide at the Base retains water to a depth of 7.5…
A:
Q: Problem 5: Draw shear and bending moment diagrams and sketch the qualitative deflected shape for the…
A: A beam system is given in the figure belowNeed to Find Draw the shear force and bending moment…
Q: Calculate the fire flow and duration required for a 60m by 120 m five story building. The structure…
A: 1. Required Fire Flow: 87.84 L/min2. Fire Duration: 120 minutesExplanation:Step 1: To calculate the…
Q: Find the principal moments of inertia about the center of mass of a flat rigid body in the shape of…
A: Mass = mArea = A =a2Density, Moment of inertia about the x-axis:
Q: Explain the significance of structural modeling in the analysis process?
A: Civil engineering project analyses make use of structural modeling extensively. It involves the…
Q: བོ---. PROBS. 6.6 and 6.7. 6.6. The area shown is symmetrical about both the horizontal and vertical…
A: Below is the clarified and detailed explanation for above tricky question.....if you are ok with my…
Q: Discuss the importance of proper backfilling and compaction in excavation projects?
A: Proper back filling and compaction are crucial to any excavation project to maintain site stability,…
Q: Compute the data for the flight plan from the following. Length of ground along N-S direction = 40…
A: Length of ground along N-S direction = 40 kmWidth of ground along E-W direction = 30 kmAverage…
Q: (4) [Text-problem 4.29] A 90-m³ basement in a residence is found to be contaminated with radon…
A: Volume of basement, Concentration of Radon, Decay rate constant, Flow, Acceptable concentration, To…
Q: Determine the location of the centroid of the area. Segments A,B, and C. I can't figure how to find…
A: Centroid will be at ( 2.5 , 4 ) from lower left cornerExplanation:
Q: A beam has an f'c = 5000 psi, fy = 60000 psi, reinforcement ratio = 0.0137. Which of the following…
A:
Q: Cross sectional area: 4 meter by 4 meter, three consecutive flocculation tanks. a) Determine the…
A: A. 4m/nB.1. v2= 50m/s v3= 30m/s2. n1= 0.3183/s n2= 7.9577/s n3= 3.1831/s3. P=0.0002WC.…
Q: Determine the vertical displacement at B (AB) and Horizontal displacement at C (Acx) by used…
A:
Q: : • Given that unit discharge in a rectangular channel is 18 m³/sec/ Im and the head loss across a…
A: Given data:Unit discharge (q) = 18 m3/shydraulic jump (HL) = 1.1 mAssume acceleration due to gravity…
Q: A flow test was conducted on an old existing pipeline to determine the coefficient C for the Hazen…
A: C = 63.84Explanation:
Q: The davit shown in the figure is supported by a cable at B and pinned at A and is subjected to a…
A:
Q: Equilibrium of Force Systems Q11) Find the reaction moment at the built-in support at A due to the…
A:
Q: 4/6 Determine the force in each member of the loaded truss. 45° 5m D 6m B 6m 5m 5000 N
A: "Since you have asked multiple question, we will solve the first question for you. If you want any…
Q: Referring to the vertical curve below, a -2% grade meets a 4.8% grade at the point of vertical…
A:
Q: What are the primary structural components of a typical reinforced concrete building?
A: It is due to their ability to be strong, durable, and flexible that reinforced concrete buildings…
Q: The 12.5-cm-diameter 20°C water jet in the figure strikes a plate containing a hole of 10.5-cm…
A:
Q: The bar 1 consists of an aluminum cover and a brass core. The data is presented in the table.…
A: Please refer explanationExplanation:Step 1: Step 2: Step 3: Step 4:
Q: Assuming that the specific gravity of the following substances is approximately the same, that is,…
A: The objective of the question is to calculate the time it will take for a particle of gravel to…
Q: Homework: Construct shear and moment diagrams using the equilibrium method. Indicate the magnitudes…
A:
Q: Determine the value of P required to start the 10° wedge to the right. Take the angle of friction =…
A:
Q: Suppose you have two identical bumper cars (we'll call them A & B). A moves towards B at 1.7 m/s.…
A: The conservation of momentum principle, which asserts that an isolated system's total momentum stays…
Q: KI-150 md hl=5m K2 60 md h2-10 m K3 300 md h3-7 m The average horizontal permeability? The average…
A:
Q: In the shaft shown below, an angle of twist of 5 degrees is observed. The modulus of (G) for the…
A:
Q: Describe the factors influencing evaporation and transpiration, and their significance in hydrology.
A: Evaporation and transpiration are the key processes in the hydrological cycle, that affect water…
Q: F6-11. Draw the shear and moment diagrams for the double-overhang beam. 4 kN/m 4 kN/m -1.5m- 3 m…
A: A double overhang beam is given we need to draw the shear force and bending moment diagram
Q: Can you please answer the following question in the picture and show all of your work in, please.
A: Detailed step by step solution is given below, still if you have any query please feel free to…
Q: Determine the vertical displacement at c by used Virtual Work method. Dont calculate the EI Ans Acy…
A: Determine the vertical displacement of the joint C using virtual work method.
Q: Calculate the distribution storage needed for equalization storage based on the following peak…
A: Let's go through the peak hourly data and find the maximum demand:12. Peak hourly demand at 6 pm:…
Q: Show step by step solution
A: FINAL ANSWER:- Therefore,the minimum coefficient of friction is 0.2167.Explanation:
Q: Think of a project (weather impact) that involves data collection. Collect (weather impact) the…
A: Project Title: Impact of Weather Conditions on Agricultural Crop Yield Introduction: Weather…
Q: of 15 m/s, estimate the direct runoff hydrograph (DRH) and the discharge of the 6 -h unit hydrograph…
A: Peak flow Average depth Infiltration loss =0.25 cm/h,Base flow It is required to find the peak…
Q: I posted this question yesterday, but the solution feels wrong. In the solution, K and Kj were taken…
A: Answer:a) At maximum flow, the speed = 40km/hr and maximum flow = 1440veh/hrb) The possible flow…
Q: 14. Free-flow speed of vehicles on a road section is 88 km/h. Jammed density is 228 veh/km.…
A: a) Traffic density when flow is maximum, k= 114 veh/km b) Possible maximum flow for road section,…
Q: As its relates to Jamaica answer the following, also include references. 1.How relevant are NEPA’s…
A: 1.) NEPA's concerns about alkalinity, acidity, and oxygen levels are highly relevant in the context…
Q: The correct answers given are: 1. 2.37 2. 1.72 Can I please have assistance to show the…
A: Shear stress,Modulus of rigidity G =40 Gpa = 40 x 103 N/mm2 Shear stress due to torsion,a= 60mm b=…
Q: The signboard truss is designed to support a horizontal wind load of 775 lb. A separate analysis…
A:
Q: A box barge 210 ft. long and 40 ft. wide floats at a draught of 18 ft. in seawater. Calculate: (a)…
A: (1) Length of box barge (2) Width of box barge(3) A box barge floats in seawater at a…
Q: Problem 1 The gate shown is rectangular and has dimensions height h = 6 m by width b = 4 m. The…
A: Below is the clarified and detailed explanation for above tricky question.....if you are ok with my…
Q: Air Leakage and Ventilation Problem: Blower Door Test A blower door test was conducted during an…
A: A leaky 1920s Toronto house loses energy due to uncontrolled air leakage. We calculated the…
Estimate the height which water will rise in a capillary tube 12mm diameter. Use surface tension = 0.0728 N/m and gamma = 9810 N/m^3
Ans. No Capillary Action
Step by step
Solved in 3 steps with 3 images
- Find the capillary rise in a tube for a water glass interface (teta) = 0° if the tube radius is 1mm and the density is 1000 kg/m³. Surface tension of water is 0.0728 N/m.Estimate the height which water will rise in a capillary tube 12mm diameter. Use surface tension = 0.0728 N/m and gamma = 9810 N/m^3 Ans. No Capillary ActionEx.1 Ans. A glass tube 0.25 mm in diameter contains a mercury column with water above the mercury. The temperature is 20°C at which the surface tension of mercury in contact with water is 0.037 kg()/m. What will be the capillary depression of the mercury? Take angle of contact 0= 130°. 3.02 cm
- Assuming that pressure will increase at a uniform rate and there is no damping of the pressure wave. Water from a reservoir that flows through a 650mm pipe at 1.8m/s is completely stopped by a closure of a 160 m valve from the reservoir. The thickness of the pipe is 25mm, bulk modulus of water is 2.2x10⁹ Pa and E of steel is 1.4x10¹¹ Pa. Determine the following: a. Celerity of the pressure wave b. Equivalent bulk modulus of water c. Pressure on the pipe after closure of the valve d. Time required to avoid water hammer e. Water hammer pressure of the velocity will decrease to 1.2m/s f. Maximum permissible discharge after the outlet valve closure. ANSWER: d) t = 0.256 sec. e) Ph=pCAV = 749.8476 kPa f) Q = AV = 0.597 m³/s a) C = 1249.746m/s b) k' = 1.562x10⁹ Pa c) Ph=pCV = 2249.5428 kPa7. What is the pressure value (PA) needed to achieve equilibrium for the figure shown (kPa)? a. 0.59 c. 1.02 b. 1.02 d. None of all these PA S.G=0.87 30 120 mmFind the capillary rise in a tube shown for a water- glass interface. ∅=0 if the tube radius is 1mm and the density is 1000kg/m³. Surface tension of water is 0.0728 N/m.
- 7. The diameters of a small piston and a large piston of a hydraulic jack are force of 60 N is applied on the small piston. Find the load lifted by the large piston, when : (a) the pistons at the same level, and (b) small piston is 20 cm above the large piston. The density of the liquid in the jack is given as 1000 . respectively. A kg [Ans. (a) 1500 N, (b) 1520.5 NJ 8. Determine the gauge and absolute pressure at a point which is 2.0 m below the free surface of water. Take [Ans. 1.962 N/em (gauge), 12.066 N/cm2 (abs.)] m' atmospheric pressure as 10.1043 Nicm. 9. A simple manometer is used to measure the pressure of oil (sp. gr, 0.8) flowing in a pipe line. Its right limb is open to the atmosphere and left limb is connected to the pipe. The centre of the pipe is 9 cm below the level of mercury (sp. gr. 13.6) in the right limb. If the difference of mercury level in the two limbs is 15 [Ans. 12.058 N/em²| cm, determine the absolute pressure of the oil in the pipe in N/cm. 10. A simple…When a 2-mm-diameter tube is inserted into a liquid in an open tank, the liquid is observed to rise 8 mm above the free surface of the liquid. The contact angle between the liquid and the tube is zero, and the specific weight of the liquid is 1.2 × 104 N/m³. Determine the value of the surface tension for this liquid. J = i N/mCOMPUTE THE CAPILLARY RISE IN mm. OF PURE WATER AT 10^0 C EXPECTED IN A 0.8 mm θ TUBE
- A welded steel cylindrical drum made of a 10-mm plate has an internal diameter of 14 m. Compute the change in diameter that would be caused by an internal pressure of 14 MPa. Assume that Poisson's ratio is 0.30 and E = 200 GPa.(a) Determine the height water at 70F will rise due to capillary action in a clean, 1/4-in.-diameter tube. (b) What will be the height if the diameter is reduced to 0.01 in.? At this temperature, water = 0.00497 lb/ft and water = 62.3 lb/ft3 . Use = 0degrees(4) Consider that we have a horizentral pipe, like shown in the sketh, which is carrying in this case, cooling water at 10 °C. The elevation of the big tank of cooling water is 100 m, the elevation of the center line of the pipe is 20 m, the length of the pipe is 2000 m. Head loss in the pipe is 0. 07 L / D) V? H. D=20 cm, the rate of flow is 0.0 a=1 ase calculate the 2g pressure in the pipe. Elevation = 100 m Elevation = 20 m L=2000 m %3D II ||