Problem 3Solve Problem 1.27, you will need the info in 1.7 to do so.PROBLEM 1.704 mEach of the four vertical links has an 8 x 36-mm uniform rectangularcross section and each of the four pins has a 16-mm diameter.Determine the maximum value of the average normal stress in thelinks connecting (a) points B and D, (b) points C and E.0.2502 m20 kNPROBLEM 1.27For the assembly and loading of Prob. 1.7, determine (a) the averageshearing stress in the pin at B, (b) the average bearing stress at B inmember BD, (c) the average bearing stress at B in member ABC, knowingthat this member has a 10 x 50-mm uniform rectangular cross section.

Answered: Image /qna-images/answer/d63f165e-3a0f-4347-ba20-72f3afac65d1.jpg

Each of the four vertical links has an 8 x 36-mm uniform rectangular cross section and cach of the four pins has a 16-mm diameter. Determine the maximum value of the average normal stress in the links connecting (a) points B and D, (b) points C and E. PROBLEM 1.27 For the assembly and loading of Prob. 1.7, determine (a) the average shearing stress in the pin at B, (b) the average bearing stress at B in member BD, (c) the average bearing stress at B in member ABC, knowing that this member has a 10 x 50-mm uniform rectangular cross section.

Each of the four vertical links has an 8 x 36-mm uniform rectangular cross section and cach of the four pins has a 16-mm diameter. Determine the maximum value of the average normal stress in the links connecting (a) points B and D, (b) points C and E. PROBLEM 1.27 For the assembly and loading of Prob. 1.7, determine (a) the average shearing stress in the pin at B, (b) the average bearing stress at B in member BD, (c) the average bearing stress at B in member ABC, knowing that this member has a 10 x 50-mm uniform rectangular cross section.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.10P: Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa

See similar textbooks

Similar questions

Problem 3. Compute the maximum tensile stress in the bracket (rectangular cross section) 80 mm 20 mm thick 40° 4.2 kN -400 mm-
The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5 kN. 2.1 Determine the tensile stress in each rod. 2.2 Determine the shear stress in pin A between the members. 2.3 If each rod is 600 mm long, determine the overall extension of the assembly. Ignore any stretch in the joint
Find the tensile stress in MPa in member AB shown in the figure All connection bars have a square cross section and the bar width is 15 mm. Points A, B and C are pin connections. Square 15 mm side 6m 3.5m C. D. 20KN
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Draw appropriate FBDs showing how the internal forces were determined. A square bar (side length = 50 mm) is welded to a fixed supporting slab. A 30-mm diameter pin is inserted in the bar. When the loading shown is applied, determine the following: a. maximum normal stress in the bar (MPa) and bearing stress between the pin and the bar (MPa)b. stress in the weld between the bar and the supporting slab (MPa)c. shear stress in the pin (MPa) and shear stress in the bar (MPa)
1 m Section of connection for AB and BC 1m An elbow shaped frame made of Al 2024 T6 aluminum has a circular cross-section having a radius of 5mm. a. Take a cut through the section where the AB and BC segments are connected (shown in the figure at point B). Define the stress types that will occur on this section as a result of loading on the frame and show the variation of these stresses on the cross-section. b. Drawing a free body diagram, show and calculate the internal loads at point C. Show the stress distribution that are caused by these internal loads on this cross-section. Do the internal loads vary along the beam BC ?
The member consists of the steel rod AB that is screwed into the end of the bronze rod Find the largest value of P that meets the following design criteria: (a) the overall length of the member is not to change by more than 3 mm; and (b) the stresses are not to exceed 140 MPa in steel and 120 MPa in bronze. The moduli of elasticity are 200 GPa for steel and 80 GPa for bronze.
1. A 60-mm diameter steel tube with a wall thickness of 3 mm just fits in a rigid hole. Determine the tangential stress developed if an axial compressive load of 12 kN is applied. Use v = 0.30 and E = 200 GPa. Answer: 0 = 6.37 MPa 2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E= 83 GPa. Compute the tangential stress in the tube. Answer: Ot = 5.20 MPa
If the flat link shown below has an allowable tensile stress of 75 MPa, then a force P 1800 N will require the link to have a minimum thickness of: 30 mm 10 mm 3.20 mm 2.60 mm 2.40 mm 2.20 mm 3.60 mm 3.00 mm 2.80 mm O 3.40 mm
A cylindrical pressure vessel is designed using steel plating with a thickness equivalent to 15 mm. The inside diameter is 460 mm and its height is 2.5-m. Solve for the maximum internal pressure that can be implied if the longitudinal stress is only up to 120 MPa, while the tangential stress is only up to 50 MPa.
1. A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use EsT=200GPA, EAL = 70 GPa, and EBr = 83 GPa. As = 480 mm? Ab=650 mm? Al= 320 mm? 2P 4P 3P 1m 2m 1.5m
Answer the ff correctly. The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
Compute for (a) the force exerted on the bolt and rivets at joints A, B, and C and (b) the normal stress in member AD, if a force P of magnitude 300 N is applied to the handles of the bolt cutter shown in figure below, from which it has a uniform cross-sectional area of 2x10-4 m22x10-4 m². 300 N 24 mm D 12 mm B E 96 mm 24 mm 24 mm 460 mm- 300 N