Design a two way slab using the Coefficient Method considering an interior panel (Case 2). The slab will carry retai storage from a commercial warehouse for service live load. The dimensions of the interior panel are 4.50 m x 5.50 m. Use 2015 NSCP Strength Design with f'c = 28 MPa and Fy = 276 MPa. Unit weight of concrete is 23.56 KN/cum. Include simple structural details as part of your output at the end of your computations. Note: Refer to the NSCP for your live load.

Design a two way slab using the Coefficient Method considering an interior panel (Case 2). The slab will carry retai storage from a commercial warehouse for service live load. The dimensions of the interior panel are 4.50 m x 5.50 m. Use 2015 NSCP Strength Design with f'c = 28 MPa and Fy = 276 MPa. Unit weight of concrete is 23.56 KN/cum. Include simple structural details as part of your output at the end of your computations. Note: Refer to the NSCP for your live load.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the following data: 1.3-10 mm 0 bars are in bundle and are in compression. 2. Steel used is of grade Fe500. 3. Tbd = 1.4 N/mm2 for M25 grade concrete. The development length that should be provided in compression zone of beam is mm.
A simply supported one way reinforced concrete floor slab has a span of 4 m. It carries a service live load of 9 kPa and a service dead load of 2 kPa. =21 MPa, =415 MPa. Use clear concrete cover of 20 mm.Determine the spacing of 16 mm main bars of the slab for minimum thickness as specified by the NSCP 2015.Determine the spacing of the 12 mm shrinkage and temperature bars for minimum thickness of slab.Determine the spacing of the 16 mm main bars of the thinnest possible slab allowed by the NSCP 2015.
ve st Semest desi Q4) Concrete is required for walls of a building that will be moderately exposed to Intrained freezing and thawing. The cross section of a wall is 300 x 1500 mm. The smallest spacing between reinforcing steel is 50 mm. The specified compressive strength of Compressive strengthe 3 concrete at 28 days is 21.5 MPa and a slump of 50 mm. Portland cement type I is used with specific gravity of 3.15, maximum size of aggregate 25 mm and fineness modulus of fine aggregate is 2.4, absorption capacity and moisture content of fine aggregate are of 0.8%, and 1.75% respectively. The dry-rodded unit weight of coarse aggregate is 1650 kg/m³, absorption capacity and moisture content of coarse aggregate are of 0.8%, and 1.75% respectively. Both aggregates have a bulk specific gravity (SSD) of (2.65. The aggregates conform to the ASTM C33-84 requirements for grading. Estimate the quantity of (cement, fine aggregate, coarse 94 8.75 aggregate and water) for 1m³ concrete. Tooox 2.65 alka…
The 20mmØ bottom bars in the figure are epoxy coated. Assuming normal weight concrete, fy= 420 MPa, and f'c=28MPa, determine the required development lengths 1. Using simplified equations 2. Using ACI full equation with calculated value of Ktr 3. Using ACI equation with Ktr = 0
PROBLEM: A rectangular reinforced concrete beam has a width of 310 mm and an effective depth of 490 mm. Concrete compressive strength (fc') is 21 MPa, and steel yield strength (fy) is 345 MPa. Use USD Method. DETERMINE: 4. Ultimate moment capacity if the beam is reinforced with 8 – 25 mm diameter tension steel. 5. Ultimate moment capacity if the beam is reinforced with 10 – 25 mm diameter tension steel.
PROBLEM: A rectangular reinforced concrete beam has a width of 310 mm and an effective depth of 490 mm. Concrete compressive strength (fc') is 21 MPa, and steel yield strength (fy) is 345 MPa. Use USD Method. DETERMINE: 1. Ultimate moment capacity if the beam is reinforced with 4– 25 mm diameter tension steel. 2. Ultimate moment capacity if the beam is reinforced with 5 – 25 mm diameter tension steel. 3. Ultimate moment capacity if the beam is reinforced with 6 – 25 mm diameter tension steel. 4. Ultimate moment capacity if the beam is reinforced with 8 – 25 mm diameter tension steel. 5. Ultimate moment capacity if the beam is reinforced with 10 – 25 mm diameter tension steel.
Question 1: 10M Stirrups 350mm 2 - 20M 2-25M+1-20M 850mm F The figure above shows the cross section of a grade beam. fc-30MPa, fy=400MPa. Max aggregate size is 20mm. Minimum spacing between bars is 35mm. Concrete cover = 40mm Determine... a) Beam effective depth (d) b) Calculate reinforcing ratio (p) c) The depth of the equivalent rectangular stress block (a), and location of neutral axis (c). d) Check the failure mode of the beam using strain diagram e) Calculate Mr (Moment of resistance) in kN.m f) Calculate balanced reinforcing ratio (Pb). Confirm your finding in item "d" by comparing current reinforcement ratio to balanced reinforcement ratio.
Design a one way slab (as shown in fig) for inside of a building. Normal weight aggregate concrete will be used with a density of 145pcf. Compressive strength of concrete = 4000psi Yield strength of steel = 60000psi LL = 250psf
A doubly reinforced rectangular concrete beam has a width of 300 mm and an effective depth of 500 mm. The beam is reinforced with 2200 mm? of steel in tension and 628 mm? of steel in compression. The effective cover for compressive steel is 50 mm. Assume that both tensioned and compressive steel yield. The grades of concrete and steel used are M-20 and Fe-250 respectively. The stress block parameters (rounded off to fırst two decimal places) for concrete shall be as per IS: 456-2000.The depth of neutral axis is
Practice Problem 2.1 A rectangular concrete beam having a width of 200 mm and effective depth of 400 mm will be designed to carry the factored design load as stated. The steel yield strength Fy=275 MPa and concrete strength fc=20.7 MPa. If the compression steel is found necessary, it will be placed 60 mm from the extreme compression fiber of the beam. Neglect the effect of the displaced concrete and use the 2010 NSCP. a) Detemine the number of pieces of 20 mm diameter tension steel for a singly reinforced section to cany a factored design moment of 20 kN-m. b) Determine the mumber of pieces of 20 mm diameter tension steel for a reinforced concrete section to carry a factored design moment of 120 kN-m. c) Determine the mumber of pieces of 20 mm diameter compression steel for a reinforced concrete section to carry a factored design moment of 120 kN-m. d) Determine the mumber of pieces of 32 mm diameter tension steel for a reinforced concrete section to carry a factored design moment of…
A simply supported one way reinforced concrete floor slab has a span of 4 m. It carries a service live load of 9 kPa and a service dead load of 2 kPa. =21 MPa, =415 MPa. Use clear concrete cover of 20 mm.a) Determine the spacing of 16 mm main bars of the slab for minimum thickness as specified by the NSCP 2015.b) Determine the spacing of the 12 mm shrinkage and temperature bars for minimum thickness of slab.c) Determine the spacing of the 16 mm main bars of the thinnest possible slab allowed by the NSCP 2015.
Problem-C. A doubly reinforced rectangular concrete beam has a width of 30mm and an effective depth of 500 mm. The beam is reinforced with 2200 mm² of steel in tension and 628 mm² of steel in compression. The effective cover for compression steel is 50 mm. Assume that both tension and compression steel yield. The grades of concrete and steel used are M20 and Fe250, respectively. The stress block parameters (rounded off to first two decimal places) for concrete shall be as per IS 456 : 2000. Find the moment of resistance of the section.