Design a chain drive to run a blower at 700 rpm for design factor of 1.5 moderate shock. The power to the blower is available from an 8 kW motor at 1400 rpm. The center distance is to be kept at 800 mm. Note the design should include the number of teeth of driven and driver sprocket, chain No, number of strands, and the length of the chain in term of chain pitch.

Design a chain drive to run a blower at 700 rpm for design factor of 1.5 moderate shock. The power to the blower is available from an 8 kW motor at 1400 rpm. The center distance is to be kept at 800 mm. Note the design should include the number of teeth of driven and driver sprocket, chain No, number of strands, and the length of the chain in term of chain pitch.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Compute the contact stress number for the gear fain pair driven directly by an electrical motor. The driven machthe is concrete mixture with moderate shock, the other data are given below. Ks= 1.00, Km 1.21, Vt =1527 St/min, Av-11 Pd= 6, np= 1750rp.m, Np 20, No= 70, F=2.00/n Tp = 900ib, Dp= 3:333 in The material used for pioin an gear is Steel
A 1000 RPM speed reducer and 12KW power drives a conveyor belt at 400 RPM. the distance between the centers is approximately 800mm. Select a suitable chain for transmission, as follows:1) Solicitation with moderate shock, abnormal operating conditions, operating 24 hours a day.
See the answer A flat belt drive system is to be designed for an application in which the input shaft speed (driving pulley) is 1725 rpm, the driven shaft speed is to be approximately 960 rpm, and the power to be transmitted has been estimated as 3.0 horsepower. The driven machine has been evaluated and found to have characteristics of moderate shock loading during operation. The desired center distance between driving and driven pulleys is approximately 18 inches.
It is required to design a chain drive with a duplex chain to connect a 15kW . 1400r.p.m electric motor to a transmission shaft running at 350 r.p.m.The operation involves moderate shocks.Assume that centre distance is nearly 40 times the chain pitch initially.What is the no of teeth on driving sprocket? What is the no of teeth in driven sprocket? Select a suitable roller chain.What is it's label? What is the pitch circle diameter of a driving sprocket? What is the pitch circle diameter of driven sprocket? Total no of chain links is Corrected center to center distance is?
A compressor is to be driven by a 30 hp, 2500 rpm DC motor and operating under moderate shock load with a service factor of 1.2. The compressor will operate at 600 rpm and using type B173 V-belt. The available small sheave diameter is 9 in and having a factor of 1.14. The arc of contact factor 0.89 and the length of belt factor is 0.97. Calculate the corrected center distance. Select one: O a. 51.5 in Оb. 49.3 in О с. 68.9 in O d. 37.5 in
;: . L The contact surfaces in a cone clutch have an ej'fective diameter of 7‘5 i semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque requiy, 5 e slipping of the clutch if an axial force applied is 180 N. This clutch is employed to connect an electric motor running um_'form!y at 1 000 Epm. with, el which is initially stationary. The flywheel has a mass of 13.5 kg and its radius of gyriy, is Calculate the time required for the flywheel to attain full speed and also the energy [y, in of the clutch.
Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, to sustain a load, which varies from 400 N to 980 N. The spring index is 6.8 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa, find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm. I
Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, to sustain a load, which varies from 400 N to 980 N. The spring index is 6.8 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa, find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and 4. Free length of the spring. 5. Ks= shear factor 6. whals factor The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm:.
A cone clutch has an angle of 12 dgrees and coefficient of friction of 0.42. Find the axial forcerequired if the capacity of the clutch is 8 KW at 500 rpm. The mean diameter of the active conicalsections is 300 mm. Use uniform wear method.
HW6 A belt drive must transmit 10 kW of power at 3000 rev/min. The wheel is 200 mm diameter and the coefficient of friction is 0.35. The lap angle is 150°. The belt tension must not exceed 50 N. Calculate the minimum number of belts required.
6. Design a clamp coupling for transmitting 36 kW, at 200 rpm. Allowable shear stress in shaft is 45 MPa, allowable shear stress in key is 40 MPa, and allowable crushing stress in key is 90 MPa. The number of bolts joining the two halves is 4. The permissible tensile stress in bolts is 60 MPa. The coefficient of friction between the muff and shaft can be taken as 0.25
Q9/ A V-belt drive consists of three V-belts in parallel on grooved pulleys of the same size. The angle of groove is 30° and the coefficient of friction 0.12. The cross-sectional area of each belt is 800 mm? and the permissible safe stress in the material is 3 MPa. Calculate the power that can be transmitted between two pulleys 400 mm in diameter rotating at 960 rpm.