Consider the expression (a-1)*(((btc)3) d). Let X be the minimum number of registers required by an optimal code generation (without any register spill) algorithm for a load/store architecture, in which (i) only load and store instructions can have memory operands and (ii) arithmetic instructions can have only register or immediate operands. The value of X is

Consider the expression (a-1)*(((btc)3) d). Let X be the minimum number of registers required by an optimal code generation (without any register spill) algorithm for a load/store architecture, in which (i) only load and store instructions can have memory operands and (ii) arithmetic instructions can have only register or immediate operands. The value of X is

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Write HCL code for the signal D_stall in the PIPE implementation.Pipeline register D must be set to bubble for a mispredicted branch ora ret instruction. As the analysis in the preceding section shows,however, it should not inject a bubble when there is a load/use hazardin combination with a ret instruction:bool D_bubble =# Mispredicted branch (E_icode == IJXX && !e_Cnd) ||# Stalling at fetch while ret passes through pipeline# but not condition for a load/use hazard!(E_icode in { IMRMOVQ, IPOPQ } && E_dstM in { d_srcA,d_srcB }) && IRET in { D_icode, E_icode, M_icode };
CCode V Consider the following Convolutional code encoder, where the initial value of all memory registers is zero. Which of the following is the correct sequence of states (S1, S2) after you feed it in the input 111? Note, for (ab) --> (cd) --> (ef), the state (ab)=(S1, S2) is the state after the first bit is fed into the encoder, and (cd)=(S1,S2) corresponds to the state after the second bit is fed into the encoder and so forth. I Select one: O a. (10) -> (11) --> (11) O b. (10)-> (01) --> (11) O c. (00)-> (01) --> (11) O d. (10)-> (11) --> (00) O e. (00)-> (11) --> (11) S₁ X Y S₂
Q1. Compute the effective CPI for an implementation of a RISC-V CPU using The Figurel. Assume we have made the following measurements of average CPI for instruction types: Instruction All ALU operations Loads Stores Branches Jumps Program astar bzip gec gobmk h264ref hmmer libquantum mcf omnetpp perlbench sjeng xalancbmk Loads 28% 20% 17% 21% 33% 28% 16% 35% 23% 25% 19% 30% Stores 6% 7% 23% 12% 14% 9% 6% 11% 15% 14% 7% 8% Clock cycles 1.1 4.2 3.3 2.8 3.0 Branches 18% 11% 20% 14% 5% 17% 29% 24% 17% 15% 15% 27% Jumps 2% 1% 4% 2% 2% 0% 0% 1% 7% 7% 3% 3% ALU operations 46% 54% 36% 50% 45% 46% 48% 29% 31% 39% 56% 31% Average the instruction frequencies of astar and perlbench to obtain the instruction mix.
Q2:- (A) Find the phicycal address if (BP) = 0100H , (SI) = 0200H , (SS) = 2000H and a displacement of 10H, of the instruction MOV AL, [BP+SI+10H]. Which the name of Addressing Modes?
Exercise 37. Give an example of an execution that is valid for a quiescently-consistent execution on atomic registers but not not valid a linearizable execution on regular registers.
Question 2. Recall that the clock cycle time in a non-pipelined processor is determined by the instruction (considering all stages) that takes the longest time to execute as no instruction can take more than one cycle. In a pipelined datapath, the cycle time is determined by the individual stage that takes the longest time as each cycle will execute exactly one stage. Now assume the distribution of time required by independent stages are as follows: IF 250 ID 350 EX 150 MEM 300 WB 200 Now answer the following questions: a) What should be the clock cycle time for a non-pipelined and a pipelined processor? Provide justification for your answer. b) How long will it take to execute the lw instruction in a non-pipelined processor? Why? c) How long will it take to execute the lw instruction in a pipelined processor? Why?
Implement and conpute the total memory traffic in bytes for both instruction fetch and instruction execution for the code that implements the expression a-(b*c)+d on 3-,2-,1- and 0- adress machines. Assume opcode occupy 1byte , adress occupy two bytes and data values also occupy 2 bytes. The word length is one byte
I want all staps for Consider a computer which has a memory which is capable of storing 4096 K words and each word in memory can be of size 32 bits. The computer supports a total of “6” addressing modes, and it has “8” computer registers. The computer supports instructions, where each instruction consists of following fields: • Mode • Operation code • Register • Register • Memory Address Given that each instruction will be stored in one memory word, discuss with a suitable diagram the format of instruction by specifying number of bits for each field of instruction. Discuss each field of instruction
Consider the instruction ADD R1, M (R1 = R1 + [M]). M is the memory address of the operand. It is a two-word instruction – first word is the op-code and the second word is the address of the operand. Give the RTL description for the complete execution (including fetch phase) of the instruction.
Multicycle execution is better than single cycle execution since it is: a. Every operation is completely carried out within a single clock cycle b. Break up operation so that each stage is executed in 1 clock cycle and allow skipping of unused stages. c. The maximum clock frequency is determined by the slowest instruction in the instruction set. d. A form of parallelism since more than one instruction is executed by the processor in any given cla
For load-store architecture, we have to load operands from memory anyways, as compared to register-memory architecture. Please answer why there are still benefits of reducing I/O traffic? Please show the benefit of load-store through an example of code.
Show how to implement the wait() and signal() semaphore operations in multiprocessor environments using the TestAndSet() instruction. The solution should exhibit minimal busy waiting.