Consider the crout shown in (Egure 1). Suppose that 711053 and 7-3750 Figure WO 319 103 1250 Part A Simplity the circuit by replacing the Y on the left (25 12, 40 12, and ry -110 3) with its equivalent & as shown in Figure 23. Determine the resistances of the equivalent à Express your answers in ohms to three significant figures. Enter your answers separated by a comma VALI vec R. R. R. Subme Part B 4. Submit A Value Determine the current suppled by the 40 V source in the crout Express your answer to three significant figures and include the appropriate units h 0 100 Units ? D

Consider the crout shown in (Egure 1). Suppose that 711053 and 7-3750 Figure WO 319 103 1250 Part A Simplity the circuit by replacing the Y on the left (25 12, 40 12, and ry -110 3) with its equivalent & as shown in Figure 23. Determine the resistances of the equivalent à Express your answers in ohms to three significant figures. Enter your answers separated by a comma VALI vec R. R. R. Subme Part B 4. Submit A Value Determine the current suppled by the 40 V source in the crout Express your answer to three significant figures and include the appropriate units h 0 100 Units ? D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the following zener clipper draw the output waveform Vz1 = 5V, Vz1 = 7V VK = 0.8v lkn ISV V₁₂ 5V 2, 72. -5V Q2 Determine The Output Waveform And Calculate The current and PIV 1kQ 1kQ 10 V 10 si www www Q. For the circuit shown in Figure below (1),find the maximum and minimum values of zener diod current. Live 5 ΚΩ www I IL 15 80-120 V 10 ΚΩ LIR 101 102 1015 S Ne 1 k0 www Iz 50 V U2 -ot V. Fumal inash
A step down converter has a load resistance R-0.5Ohms, an input voltage Vs-200V and a battery voltage E-OV. The average load current la-250A and the converter frequency is 1000 Hz. The value of the inductance L that would limit the maximum load ripple current to 5% of la, would be equal to: Select one: O a. 15 mH O b. None of these O c. 4 mH O d. 9 mH
4- Design a boost converter that will have an output of 60 V from a 24-V source. Design for continuous inductor current and an output ripple voltage of less than one percent. The load is a resistance of 50 2. Assume ideal components for this design. VL ooooo ip - ^
Draw the output on top of the input waveforms for the circuits below. For all circuits in this question, assume that +Vout(max)= +10V and -Vout(max)= -10V .
For a Step-down chopper, design the circuit with 200ohm effective input resistance and 10ohm output resistance? Calculate the duty cycle and efficiency. Assume the input voltage accordingly.
Write the loop equations for a Buck converter in the two modes if the inductance is characterized by a combination of inductance L1 in series with an equivalent resistance r1, filter capacitance is characterized by a capacitor C1 in series with resistance r2. Also assume that the controlled switch has a drop of 0.4V and the freewheeling diode has a voltage drop of 0.65v. Draw the corresponding equivalent circuits in each mode.
The buck converter with resistive load has the input voltage of 30[V], the output voltage of 10[V] (constant), and the switching frequency of 40 [kHz]. If the output average power is 25[W], then determine the size of the inductor such that the minimum inductor current is 25 % of the average inductor current.
Boost Converter Design A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
100 W at 60 V from a Specify the 2 percent. size. Design a buck-boost converter to supply a load of 30 V source. The output ripple must be no more than duty ratio, switching frequency, inductor size, and capacitor
A single-phase full-wave converter in the figure below is supplied with a 120-V, 60-Hz source. The load is highly inductive and the load current is continuous and free of ripples. The electromotive force is neglected (E 0) and the resistance has a value of R = 10 Q. The delay angle is equal to 31.8°. The average output current is 9.18A and the nth harmonic component is expressed as below. The harmonic factor (known as THD) would be equal to: R 2. vZ.1. Ir = Vo n. T +Yi, = I, E Select one: O a. 58.3% Ob. 48.3% O C. 78.3% Od. 68.3%
Please answer both subpart for like this please Asap for like..
a. b. C. There is a dc-dc converter that provides isolation between input and output current. Identify the converter type and describe the operation. Draw the equivalent circuit to support the explanation. Assume the converter operates in continuous-current mode. Explain why a switched -mode dc-dc converter is better that a linear regulator. As an electrical engineer, you are required to design a chopper circuit with an output voltage of 10 V from a 30 V input with switching frequency of 50 kHz. The circuit is operated in continuous current, and output ripple voltage is less than 0.8% with resistance load of 30 Q. Assume the inductor value is 50 % larger than Lmin and assume ideal components for this design. Identify the chopper type and construct the circuit with IGBT as the power switching.