I need the answer as soon as possible Consider the attitude dynamics of an aircraft with a transfer function2s+0.1G(s)s(s'+0.1s+4)Determine the transient response specifications,including Peak Time, Settling Time, Damping Ratioand Overshoot (%).

Answered: Image /qna-images/answer/b6a926bb-8222-4386-9f43-abc60e83473a.jpg

Answered: Consider the attitude dynamics of an…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

xa 0- 1 point) Which of the systems presented on Fig. 2 is stable and which unstable? (a) t Fig. 2. System response (b) A
b. Using Simulink, simulate the transfer function airflow response, Q(t) (air entering respiratory system) for a sine wave input pressure Pao(t)= 2.5 cm·H2O (i.e. 5 cm·H2O peak-to-peak) at 15 breaths min' (or 0.25 Hz) for each lung model. Use the following parameters: -1 i. RC model: R= 1cm·H2O's L' and C=0.2 L·cm·H2O¯ RIC model: R= 1cm·H2O's·L', C= 0.2 L·cm·H2O¯ , and I= 0.01 cm·H2O L-s² Two-compartment model: R. = lcm H2O's L', Rp1,2 = 0.5 cm·H2O•s·L', Cp1,2=0.2 L·cm·H2O', and I= 0.01 cm H2O·L-•s² Mead model: R. = 1cm·H2O•s L', Rp = 0.5 cm:H2O•s·L', C1 =0.2 L·cm·H2O', Cw=0.2 L·cm·H2O-', C, =0.005 L·cm·H2O', and I= 0.01 cm H2O·L-1·s² ii. iii. iv.
2- Using Matlab, what are the step response curves of the closed-loop system, as shown in fig.1. the feedback represents the second-order dynamic system. (fill in the following table) For=0.4 Wn 1 3 6 9 10 R(S) 0.1 0.3 0.6 0.9 1 For w 5 rad/sec 3 Settling time Peak response 2 Wn s(s+23wn) Settling time Peak response C(s) Discuss the follow Which parameters or w occur on the rise time of the response? Which parameter increases the speed of response? Which parameters can be decreases the response amplitude? Which parameter decreases the steady error state? fig.2
The Gilles & Retzbach model of a distillation column, the system model includes the dynamics of a boiler, is driven by the inputs of steam flow and the flow rate of the vapour side stream, and the measurements are the temperature changes at two different locations along the column. The state space model is given by: x = 0 00 -30.3 0.00012 -6.02 0 0 0 -3.77 00 0 -2.80 0 0 Is the system?: a. unstable b. C. not unstable x+ 6.15 0 0 0 0 3.04 0 0.052 not asymptotically stable d. asymptotically stable -1 u y = 0 0 0 0 -7.3 0 0 -25.0 X
The governing equation of motion for a base motion system is given by (assume the units are Newton) mä(t)+ci(t)+kx(t) =cY@, cos(@,t) +kY sin(@t) %3D Given that m = 180 kg, c = 30 kg/s, Y = 0.02 m, and о, — 3.5 rad/s %3| 1. Use Excel or Matlab to find the largest value of the stiffness, k that makes the transmissibility ratio less than 0.85 2. Using the value of the stiffness obtained in part (1), determine the transmitted force to the base motion system using Matlab or Excel. 3. Display and discuss your results.
A velocity of a vehicle is required to be controlled and maintained constant even if there are disturbances because of wind, or road surface variations. The forces that are applied on the vehicle are the engine force (u), damping/resistive force (b*v) that opposing the motion, and inertial force (m*a). A simplified model is shown in the free body diagram below. From the free body diagram, the ordinary differential equation of the vehicle is: m * dv(t)/ dt + bv(t) = u (t) Where: v (m/s) is the velocity of the vehicle, b [Ns/m] is the damping coefficient, m [kg] is the vehicle mass, u [N] is the engine force. Question: Assume that the vehicle initially starts from zero velocity and zero acceleration. Then, (Note that the velocity (v) is the output and the force (w) is the input to the system): A. Use Laplace transform of the differential equation to determine the transfer function of the system.
A velocity of a vehicle is required to be controlled and maintained constant even if there are disturbances because of wind, or road surface variations. The forces that are applied on the vehicle are the engine force (u), damping/resistive force (b*v) that opposing the motion, and inertial force (m*a). A simplified model is shown in the free body diagram below. From the free body diagram, the ordinary differential equation of the vehicle is: m * dv(t)/ dt + bv(t) = u (t) Where: v (m/s) is the velocity of the vehicle, b [Ns/m] is the damping coefficient, m [kg] is the vehicle mass, u [N] is the engine force. Question: Assume that the vehicle initially starts from zero velocity and zero acceleration. Then, (Note that the velocity (v) is the output and the force (w) is the input to the system): 1. What is the order of this system?
P.3: An input of 25t³u(t) applied to the input of a Type 3 unity feedback system where 210(s+4)(s+6)(s+11)(s +13) $³ (s+7)(s+ 14)(s +19) G(s) = Find the steady-state error in position. R(s) + E(s) G(s) SR(s) e(co) = lim- 01+G(s) C(s)
Multiple DOF SystemsA 2-D spring-mass, frictionless system has the following parameters:m1 = 72m2 = 27k1 = 381k2 = 183x1,0 = 0 mx2,0 = 1 mv1,0 = -1 m/sv2,0 = 0 m/s In MATLAB, solve numerically for x1(t) and x2(t).
For the model defined in Question 1, is the closed loop system with the negative feedback control law? 0 0 0 ;]* X 0 u=-Kx= O a. O b. O c. unstable 0 1 0 asymptotically stable not unstable O d. not asymptotically stable
Problem 2. A linearized state space model of a three blade speed wind turbine with a 15 m radius working at 12 m/s wind-speed and generating 220 V is -5 5 1 -10.5229 -1066.67 -3.38028 23.5107 993.804 3.125 -23.5107 Wgm 10 -10 Wgm y = [ 0 0 0 1.223 × 10° 0] Wgm where 3 is the pitch angle of the wind turbine blades, { is the relative angle of the sec- ondary shaft, i is the angular velocity of the secondary shaft, wg is the generator speed, Wgm is the generator measurement speed, u is the pitch angle reference, and y is the active power generated. (a) What is the maximum number of poles that the transfer function could have? How many poles does it have?
A small mixing tank with a long discharge line is attached to an input source pump: R1 R2 C Ps I a) Develop the Transfer function for the height deviation as result of a supply pressure deviation: H(s) as a function of the linearized resistances, the tank capacitance, and line inertance. When P,(s) modeling this, assume that the resistance and inertance are both throughout the lines such that the same pressure drop is across R2 and I. (Note, this can also be modeled using an equivalent electrical circuit where I and R2 are in series)

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Consider the attitude dynamics of an aircraft with a transfer function 2s+0.1 G(s) s(s´+0.1s+4) Determine the transient response specifications, including Peak Time, Settling Time, Damping Ratio and Overshoot (%).