Answered: Cônnecting Ród óf å Diesel Engine cross…

Cônnecting Ród óf å Diesel Engine cross section. It is subjected to a force of 85KN. Calculate the Tensile Stress developed in the Rod 21mm Emm Smm 35m 21mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Related questions

Q: A steel rod is subjected to a stress of 200 MPa and has Young's modulus of 200 GPa. Calculate…

Q: A hollow tubular component is made of Steel having a Young's modulus of 205 GPa and yield strength…

A: Given: Young's modulue (E)=205GPaYield strength σy=250MPaExternal diameter Do=45mmThickness…

Q: ort square is 1 1/2 inches x 1 1/2 inches in cross section. it is on an axial tensile load of 11,000…

Q: 1.) A long flat steel bar 6 in. wide and 3/8 in. thick has a 2.5 in. diameter circular hole…

Q: Find stress of a aluminum cylinder of diameter 12.8mm and gauge length 50.8mm. The force applied is…

Q: A hollow cylinder of external diameter 50 mm and internal diameter 30 mm is subjected to tensile…

Q: Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by…

Q: H.W.8: Calculate the stresses, if the strains displayed on the lement have been applied. Use all…

A: To obtain the required stresses, we must first determine the principal strains in the element using…

Q: 4. A ring made of 2-5 cm diameter steel bar carries a pull of 10 kN. Calculate the maximum tensile…

A: Given: The diameter of ring, d = 2.5 cm 0.025 m The load, P = 10 kN The mean radius, R = 15 cm =…

Q: 1. The cross- sectional area of each member of the truss is 1200 mm?. Calculate the stresses in…

Q: c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile…

Q: A rectangular plate 50 mm × 10 mm with a hole 10 mm diameter is subjected to an axial load of 10kN…

Q: For the structure below, calculate the diameter of the pin G, considering that its allowable stress…

Q: The shaft of a hand operated wire rope hoist is supported on bearings A and B. The shaft is keyed to…

Q: A brass rod of diameter 50mm and of length 250mm which is subjected to a tensile liad of 300kN when…

A: (a) Diameter of rod = 50 mm Area (A) = πd24Area (A) = 3.14 x 0.0524Area (A) = 0.0019625 m2…

Q: 2. A hollow cylinder 2 m long has an outside diameter of 50mm and inside diameter of 30mm. If the…

Q: ick as shown in the ield strength of the 260 N/mm², and plastic moment of nape factor.

Q: 1. A reciprocating steam engine connecting rod is subjected to a maximum load of 65 kN. Find the…

A: Question (1) is Solved here. For Other Question, Please Post this Question.

Q: An iron column of annular cross-section has an outer diameter of 200 mm and is subjected to a force…

A: Given Data⇒Iron column of annular cross-sectionOuter diameterD=200 mm=0.2 mForceF=75 KN=75×103…

Q: A thin cylinder of 100 mm internal diameter and 5 mm thickness is subjected to an internal pressure…

A: Introduction: Internal pressure causes a hoop and longitudinal tension in a thin-walled tube or…

Q: Calculate the normal stresses (in Pa) at point Bof the bracket caused by the 23010N force. E4.png -…

Q: A hollow short cast iron column has outside and inside diameters 250 mm and 150 mm respectively. The…

Q: A rigid rod AB is pinned at A and attached at B to cable BD supporting the loads shown in Figure 1.…

A: Given data: Yield tensile stress of cable, σ = 207 MPa. Diameter of pin D, d = 15 mm. Draw a…

Q: A Portable Crane will be designed as shown in Figure which is able to withstand dynamic loads. The…

Q: A 150 inch long aluminum bar is subjected to a tensile stress of 25000 psi. Find the elongation. (E…

Q: a cylindrical disk with diameter 40 mm and thickness 2 mm is compressed stress = applied…

A: As this is a simple question related to the strength of material subject. As stress formula is given…

Q: Calculate the resulting stress in an aluminum wire, 4-m long and 2.6 mm in diameter, if a 12.5 -kg…

Q: 3. A wrought iron rod is under a compressive load of 350 kN. If the permissible stress for the…

A: We are suppose to solve only one question. Please post other question as a separate question. For…

Q: Calculate the normal stress in each segment if P=375KN. The cross-sectional area for each layer is…

Q: The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of…

Q: 2 A hollow short cast iron column has outside and inside diameters of 250 mm and 150 mm…

Q: A hollow compression member with circular cross section having outer diameter 2 times the inner…

Q: A wrought iron rod is under a compressive load of 350 kN. If the permissible stress for the material…

A: Compressive load on the rod, P=350 kN=350*103 N Permissible stress for the material, σ=52.5 N/mm2

Q: 1. Determine the shear, tensile and bearing stresses for the structural connection shown in Fig. 1.…

Q: Calculate the normal stresses (in Pa) at point Bof the bracket caused by the 25139 N force. - 540 mm…

Q: A 100N load is added to the end of circular cross section steel rod that has a length of 0.3m and a…

A: GIVEN DATA- Length of bar L=0.3m Diameter of bar d=0.025m Load P=100N Young Modulus…

Q: 4. A ring made of 2.5 cm diameter steel bar carries a pull of 10 kN. Calculate the maximum tensile…

A: We know that a ring composed of steel bar with a diameter of 2.5 cm has a draw of 10 kN. The maximal…

Q: The state of stress shown below is from the surface of a bar under axial and torsion loading.…

A: Given data: The value of stress in x-direction is, σx=60 MPa. The value of stress in y-direction…

Q: 1. A 150 inch long aluminum bar is subjected to a tensile stress of 25000 psi. Find the elongation.…

Q: Calculate the maximum stresses due to the Pload = 2000 N over the cross section. Also draw the…

A: Stress distribution due to direct load

Q: An iron column of annular cross section has an outer diameter of 200mm and is subjected to a force…

Q: A steel rod of area of cross-section 3.14× 10-4 m2 is stretched by a force of 100kN. Calculate the…

A: As given in question, Cross sectional area of rod = A = 3.14 x 10-4 m2 Force on the rod = F = 100 kN…

Q: Calculate the maximum stress in a 25 mm thick perforated bar and show its location on the figure.…

Q: A 3-in. by 6-in. steel (E-29,000 ksi) bar (4-foot long) is subjected to the loads shown. Calculate…

A: Find the stress at point A and Point B.

Q: I.W.1// A steel rod of cross sectional area 1000mm? and two aluminum rods each cross sectional area…

A: We are suppose to solve only one question. Please post other question as a separate question.

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

A Connecting Rod of a Diesel Engine in of an "I" cross section. It is subjected to
a force of 85KN. Calculate the Tensile Stress developed in the Rod
21mm
Emm
5mm
35mm
21mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
A simply supported wood beam is subjected to point load P at mid-span. The stresses on element C are known to be ??x=-92 psi and txy= -7 psi. Find the principal stresses on the element and show them on a sketch of a properly oriented clement.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
Find stress of a aluminum cylinder of diameter 12.8mm and gauge length 50.8mm. The force applied is 47,500N.
An iron column of annular cross section has an outer diameter of 200mm and is subjected to a force of 74kN. Find the thickness of the wall in mm if the allowable compressive stress is 10MPa.
a wooden bar is subjected to a tensile stressof 5mpa. the value of normal stress across a section, which makes an angle of 25 degrees with the direction of the tensile stress is (cos-1(0.6428)=50)