Change of Ttork required by a machine for rotational movement with rotation angle T(0)=5000[1+5cos(30)-6sin (30)] (Nm ) is given as. The rotation speed of the machine is below 711 r/min mass moment of inertia required to allow it to move without landing and without leaving above 729 rpm find its value. Please select one: A.241,473 kg-m B.119,592 kg-m2 C.183,181 kg-m D.221,264 kg-mi E.165,845 kg m 2. F.262,223 kg * m G.126,304 kg m 2 H.150,179 kg-m

Change of Ttork required by a machine for rotational movement with rotation angle T(0)=5000[1+5cos(30)-6sin (30)] (Nm ) is given as. The rotation speed of the machine is below 711 r/min mass moment of inertia required to allow it to move without landing and without leaving above 729 rpm find its value. Please select one: A.241,473 kg-m B.119,592 kg-m2 C.183,181 kg-m D.221,264 kg-mi E.165,845 kg m 2. F.262,223 kg * m G.126,304 kg m 2 H.150,179 kg-m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

Kinetic energy when θ=0° polar moment of inertia at O (kg.m2) work done by weight is (Joules) extension of spring when θ=90°. (m) angular velocity when θ=90° (rad/s)
Four masses A, B, C and D as shown below are to be completely balanced. Find the followings: v The axial distance between the planes of rotation of B and C(mm) v The magnitude and angular position of mass of Mp{Kg) v The angle between mass A and D (LAOD-7degree) A B. D 80 Mp Mass (kg) Radius 125 150 100 (mem) 50 60 200 120 A B 115mm
1. Given: N Specific Weight = 25 m3 %3D • Mass = 2.2 Ibs m • Acceleration = 32.2 s2 Find: Diameter of Cylinder in inches • Remarks: Show your complete solution (with UOM) and conversion.
The small particle of mass (800 gm) spinning with angular velocity (w₁ = 2.3 rad/s, at r₁ = 400 mm), if we use force (F) to change the Angular velocity to (w₂, and r₂ = 250 mm) the value of F is: W1 Select one: A. None B. F = 5.63 N C. F = 9.47 N D. F = 3.52 N F
Pages Le EXtract Object View Edit OCR Sign Comment Page Organization Convert Protect Start ASSIGNMENT FINAL 20... Q7) A horizontal table rotates freely in a horizontal plane about a frictionless vertical axle. The table has a moment of ineria 200 kg.m² and a radius R = 2.0 m. A student whose mass is m = rim of the disk toward its center. If the angular speed of the system is 2.0 rad/s when the student is at the rim, what is the angular speed when he reaches a point r = 60 kg walks slowly from the M 0.50 m from the center? 11 1 7/7 We HA 144a. Hem t A A L
1.A rotor has an inner radius of 10.0 cm and an outer radius of 25.0 cm. It is fixed to a frictionless axle that goes through its center. The moment of inertia (I) of the rotor is 0.0235 kg m2. A set of 5 constant forces act on the rotor, as shown in the diagram below. (a) Find the net torque acting on the rotor, in units of Nm. Be sure to give both the magnitude and direction. (b) Find the angular acceleration of the rotor, in units of rad/s2. Give both the magnitude and direction. (c) Assuming it starts from rest at t = 0, how long does it take for the rotor to reach an angular speed of 565 revolutions pre minute (rpm)? Give your answer in seconds. (d) At t = 2.50 seconds, how many complete revolutions will the rotor have made?
Find Ixx for the given Plane, where b =160m, d;=25m, b2=20m, d2=12Om, b3=50m & d3=20 m b3 d3 b2 d2 di bi The value of X= (unit in m) The value of Y= (unit in m) The moment of inertia for sec 1 = lyy1 = (unit in m4) The moment of inertia for sec 2 = lyy2 = (unit in m4) The moment of inertia for sec 3 = lyy3 = (unit in m4) The moment of inertia of the given plate = lyy = (unit in m4)
A flywheel with moment of inertia 0.8kgm2 rotates with a speed corresponding to 8 revolutions per second. What is the rotational kinetic energy of the flywheel?
(2) lahai Q1-e) Kinetics: is used to predict the motion caused by given forces or to determine the forces required to produce given motion True False
Find tec for the given Plane, where b150m d25m by20m, d90m by50m & d25 - (Enter ariy the values in the bases by referring the unit given in brackets Also uplosd your hand written answers in the ink providecd) b di di bi The value of - (unit in m) The value of (unit in m) The moment of inerta for seclot (unit in m The moment of nerta for sec 2 lec (unit in m The moment of inertia for sec 3 -lud- (unit in m The moment of inerta of the given plate- = (unit in m)
Number of teeth of gears z1: 22 Tooth numbers of gears z2: 90 Tooth numbers of gears z3: 23 Tooth numbers of gears z4: 77 The efficiency of gear pairs ηd: 0,96 The efficiency of the bearing pairs ηr: 0,94 Electric motor speed: 2050 Belt speed (v) (m / s): 1.30 Required force for belt movement (N) g: 2200 a) Find the diameter of the drum? b) Find the required motor power?
An engine drives a machine. The torque equations is given below. The moment of inertia of the rotating components are 54kgm². The average speed of the system is 300 rpm. T machine = 1500+ 318.310 € (0 → π,π → 2π) and repeat Tengine = 2000 + 500 sin0 Calculate: 1.Draw the crank effort diagram and show the values of all the relevant points. (2.5048 Rad) 2.The percentage velocity variation over the cycle. (0J, 0%) 3.The maximum instantaneous acceleration (-29.726 rad/s2)