Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral. 122-77-77122 Dimensions in millimeters -34 Answer: y = i 68 mm

Q: A shaft is made from solid material of density 7800 kg/m³ and E= 210 GN/m² to be applied for this…

A: The term "shaft" typically refers to a part with a circular cross-section that spins and transfers…

Q: A drum can rotate about a fixed-point O. The A block is attached to a cord wrapping around the drum.…

A:

Q: EA 4 Fo Two cables are used to suspend a bar that is approximated as rigid. A force is applied at…

A: Draw the diagram of the deflection in bar. Apply moment equilibrium about point O.…

Q: You only know one point on a pump curve, where a water pump produces 20 m of hydraulic head at flow…

A: A pump's performance curve shows how well it will operate in terms of flow and pressure head. For a…

Q: A bar is attached to the spring at the point C. The left end of the bar is pin supported and can…

A:

Q: A bar is attached to the spring at the point C. The left end of the bar is pin supported and can…

A:

Q: (b) Electrolytic Tough Pitched Copper is often used in telecommunications applications. Justify why…

A:

Q: A rigid (closed) tank contains 16 kg of saturated water at 90 °C. If all of this water is in the…

A: Given: T = 90 deg C mass m = 16 kg

Q: A cylindrical steel tank with a diameter of 1.8m and a height of 2m, is insulated with polyurethane…

A:

Q: r the below given 3 DOF (Degree of Freedom) arm, determine the forward kinematic model, using D-H…

A: solution of above problem is below:

Q: The coefficient of friction between the cylinder and the brake is 0.3. If the force P applied the…

A: The coefficient of friction, f = 0.3 The force applied, F = 20 N The length, d = 1 m The initial…

Q: Locate the centroid of the given area under the curve x = y³. i) Select an element horizontal to x…

A:

Q: A rigid (closed) tank contains 16 kg of saturated water at 90 °C. If all of this water is in the…

A:

Q: In the figure shown below, the washer is sliding outward on the rod with a velocity of 1-2 m/s when…

A:

Q: QUESTION 1. The diameter of a pulley that is connected to the mid-span of a hollow shaft is 175mm.…

A: Given: The diameter of pulley, D = 175 mm = 0.175 m The ratio of diameter of pulley, D1/D2 = 1/2 The…

Q: An engine working on the Otto cycle has 1 kg of air entering at 315 K and a volume of 0.6 m³ at the…

A:

Q: Consider the truss shown in (Figure 1). AE is constant. Take L = 7.9 ft. Figure 61 6k 68

A:

Q: A balloon goes vertically upward at a constant speed sec/m7, and when it was at a height of 134.4…

A:

Q: An ammonia simple saturation cycle operates at 35 psia suction pressure and 172 psia condenser…

A:

Q: How to do the rest sub part

A: Given  Length, L = 10 cm  Area, A = 2 x 2 cm2 Find   Tensile strength   Change in length

Q: A 50 Horsepower Diesel Engine with a brake thermal efficiency of 30% uses fuel oil with HV=18500…

A: Brake power of Diesel engine, B.P.=50 HPBrake thermal efficiency of the engine, ηbth=30 %Heating…

Q: how did they get Fc

A:

Q: 16-138. Peg B on the gear slides freely along the slot in link AB. If the gear's center O moves with…

A: given; velocity at center (V0)=3m/sacceleration(a)=1.5m/s2radius(r)=150mm…

Q: first one

A: Given data as per the question θ=tan-112

Q: A train started moving from rest with a constant acceleration, and at one time it was traveling at a…

A: Given: Initial velocity, u = 30 m/s Final velocity, v = 50 m/s Distance, s = 160 m

Q: The brass rod shown in Fig. 3 has a diameter of 20 mm. The collar D moves along the rod and strikes…

A: Given:d=20 mmE=100 GPai) W=1000 Nh=5 mmii) W=10 Nh=500 mm NOTE:According to ABrtleyby's policy we…

Q: In a rolling operation using rolls of diameter 500 mm, if a 25 mm thick plate cannot be reduced to…

A: Rolling operation: Rolling is a metal forming process, and metal forming is a deformation process…

Q: 19 Consider a pan of water being heated (a) by placing it on an electric range and (b) by placing a…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Determine the Actual Torque Required, TA

A:

Q: Design a pneumatic sequence valve circuit for clamp- and-drill devices as shown in Figure A2Q1. Give…

A: Given : To find: To draw a circuit to perform clamp and drill

Q: Three evaporators operating at the same temperature 24 F having 10, 30 and 20 Tons of refrigeration…

A: Given: The temperature of all the evaporators: →T1=24 F=268.70 K And the refrigeration capacity of…

Q: The system shown starts from rest. Determine the velocity of the crate when it has moved 1 m. 45 kg…

A: given: m=45kgM=50Nmμ=0.4θ=20°IA=4kgm2r=0.15m

Q: A simply supported wood beam with a span of L = 14 ft supports a uniformly distributed load w. The…

A:

Q: A hydraulic turbine running at 1700 rpm at a head of 70 ft. has an efficiency of 90%. The flow is 65…

A: Turbines are widely used to obtain some amount of work. When we talk about hydraulic turbines, water…

Q: Locate the centroid of the plane area shown. y Vertex Parabola 60 mm 60 mm -75 mm

A: Given Shade Zone To find Centroid

Q: a) Determine the slope of end A of the cantilevered beam.

A:

Q: A steel cube is to be heated from 120°C to an average temperature of 180°C in 45 minutes. One side…

A:

Q: H.0/Shewrforee aved 1Beanellng Momeent 4m

A: Shear force at a section can be understood as a resultant transverse force either from the left or…

Q: Determine the coordinates of the centroid of the shaded area.

A:

Q: nce with the composit anaerobic digester

A:

Q: Two cables AB and AC are acting on the pole with forces FA-540N and FAC=560N with parameters…

A: Given that: FAB = 540 N x1 = 4 m, y1 = 3.5 m L = 5.5 m It is required to determine the vector form…

Q: A bronze sleeve is slipped over a steel bolt and held in place by a nut that is turned to produce an…

A:

Q: Ball joints connect the ends of each of the struts as shown. The resulting structure supports a…

A: Given: The variable, a = 6.6 cm The variable, b = 12.4 cm The variable, c = 12 cm The variable, d =…

Q: A simply supported wood beam with a span of L = 14 ft supports a uniformly distributed load w. The…

A:

Q: drum can rotate about a fixed-point O. The A block is attached to a cord wrapping around the drum.…

A:

Q: site, a uniform pole of length(1)=6.00m and At a construction mass(m)=66.2kg is connected by a hinge…

A: (a) Draw the free-body diagram of the pole.

Q: An aircraft has the following relevant specification outlined below: Weight: 329 kN Wing planform…

A: Given: The weight, W = 329 kN The planform area, A = 191 m2 The drag polar, CD = 0.01+0.064CL2 The…

Q: Find the longitudinal strain when a bar is stretched to double in its length. Select one: O a. 2.00…

A: Given: initial length, L1 = L Final length , L2 = 3L To find : longitudinal strain

Q: Given the points A( – 5, 6, – 4), B( – 2, — 10, 6), and C(4, 0, 5), find (a) the angle between AB →…

A:

Q: Determine the x- and y-coordinates of the centroid of the shaded area.

A:

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.