If you could assist on the below, the questions are below and the information is in the image attached, Thank youCalculate the shear stress in the shaft using the information above.Calculate the angle of twist in the shaft. The diagram here shows the layshaft and pulleys in a pump system design to circulate the coolant form the tank.The initial design specifies a 50kW motor with a pulley arrangement to rotate the shaft at 250 RPM. This producesa torque at the drive pulley of 1910Nm, resulting in the motor torque and the pump resistance causing a torsioneffect in the shaft between the two pulleys.1910NThe shaft is machined from a solid steel bar with an initial design diameter of 40mm. The shear stress in the shaftis to be limited to 120MPA (120N/mm?) and a Modulus of Rigidity of 75GPA. If the distance between the motor andpump pulleys is 840mm.

To calculate the shear stress and angle of twist in the shaft

Answered: Calculate the shear stress in the shaft…

Engineering

Civil Engineering

Calculate the shear stress in the shaft using the information above. Calculate the angle of twist in the shaft.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

00 F10 F11 Y F12 Scr Lk PrtS C H V DURING A TEST OF A FRANCIS WHEEL HYDRO ELECTRIC POWERPLANT, THE POWER OUTPUT IS 4 MW AND THE VELOCITY IS 7.5 H/S. THE INSIDE DIAMETER OF THE PENSTOCK IS 3 FT, LENGTH IS 350 FT AND THE ELEVATMON OF THE CENTERLINE OF THE TUR- BINE NO2ZLE IS D FEET ABOVE THE TAILRACE HEADWATER ELEVA- TION 1300 FT, FRICTION FACTOR=0.4, EXIT VELOCITY IN THE PRAFT TUBE 1.6 FT/S IF THE OVERALL EFFICIENCYIS 80%,DETERMINE: • THE TALWATER ELEVATION IN FEET. •THE PRESSURE AT THE BASE OF THE NOZZLE IN PSI. MODULE ASSIGNMENT %3D
(a) A storage tank is connected to a piping system as illustrated in Figure P1. Water at temperature of 20°C in the storage tank flows through a piping system with the pipe's diameter of 5 cm and discharges from a nozzle to the atmospherie at velocity of 3.5 m/s. The diameter of the nozzle is 3cm. Galvanized pipe is used and installed in this piping system. All the fitting components installed in this system such as regular 90° and tees are flanged type. The Water at 20°C 21 m D= 5 cm d = 3 cm Figure P1 i. By using suitable assumptions, predict the friction factor of this piping system (Including the Moody Chart is necessary).
(a) A storage tank is connected to a piping system as illustrated in Figure P1. Water at temperature of 20°C in the storage tank flows through a piping system with the pipe's diameter of 5 cm and discharges from a nozzle to the atmospherie at velocity of 3.5 m/s. The diameter of the nozzle is 3cm. Galvanized pipe is used and installed in this piping system. All the fitting components installed in this system such as regular 90° and tees are flanged type. The Water at 20°C 21 m D= 5 cm d = 3 cm Figure P1
A steam turbine is to operate on a simple regenerative cycle. Steam is supplied dry saturated at 40 bar, and is exhausted to a condenser at 0.07 bar. The condensate is pumped to a pressure of 3.5 bar at which it is mixed with bleed steam from the turbine at 3.5 bar. The resulting water which is at saturation temperature is then pumped to the boiler. For the ideal cycle sketch the process on the T-s diagram and calculate, neglecting feed pump work,The amount of bleed steam required per kg of supply steamThe thermal efficiency of the plantThe specific steam consumption
B A shaft turns at 150 rpm under a torque of 1500 Nm. Power transmitted is (a) 15 kW (b) 10R kW (c) 7.5 kW (d) 5 kW
Determine the reaction at A in the given figure. (please submit your solution for this item) * 2 kN/m 600mm- 450 mm 300 mm
Q1) Choose the correct answer. 1) If you decrease the discharge static head, what will happen to the flow? a. Static head and friction head b. It will decrease c. It will increase d. none 2) The moving part in centrifugal pump is a. impeller. b. diffuser. C. both a & b. d. neither a nor b.
Ql:-A cylinder of 1lft diameter and 2ft length floats in a tank that contains a liquid of specific weight .A u-tube manometer is connected as shown in figure. What is the weight of the cylinder whose upper the surface is flush with fluid surface PA--0.1 psi Water 2 ft Cylirder Gage fluid SG- 1.5 Sp wt.y 0.5 ft 02. w1
Glycerin of SG 1.26 flows through the nozzle shown and deflects the mercury in the U-tube gage. What is the pressure at B in kPa? A 2.75 h B Hg(13.6)
Assuming smooth contact surfaces, determine the reactions A, B, C and D on the cylinders as shown in the fig. Show your solutions in two ways.
A pipe 2000 m in length witha flow rate of 2 m'/s. At the end of the 600 mm pipe, a valve is provided. If the water in the supplied tank before it flows into the pipe is compressed at 2 Mpa with a volume of 2 m and a volume of 1.99 m at a pressure of 4 Mpa. Find the pressure if the valve is closed in 20 seconds. O 3712 kPa O 2678 kPa O 4474 KPa O 1415 kPa
EN.3060 - Transport Phet Consider the system shown below in which a rod is contained within a coaxial cylinder. The system is aligned vertically. The rod has a radius Ri and the outer cylinder has a radius of R2. The region between the rod and outer cylinder contains an incompressible Newtonian liquid that has a density p and viscosity u. The rod is being moved in the positive z-direction at a constant velocity V while the outer cylinder is stationary. Assume the liquid is in steady fully developed laminar flow and there is no pressure gradient acting on the liquid in the direction in which the rod is moving. (a) Write the simplified forms of the Continuity and Navier-Stokes Equations in cylindrical coordinates that will be used for solving for the velocity profile in the liquid. (b) Write the applicable boundary conditions that will be used to solve for the velocity profile. (c) Solve for the velocity profile v in terms of r, R1, R2, V, p, g and u. (d) Assume the rod has a radius RI=3…