(c) Elaborate the principles of vacuum forming process forthermoplastics, given a shaped form.Question 5[4](a)i. Explain the Spin welding process with the help of a diagram.[6]ii. Name the two requirements for the process to be successful?[4]i. Which are the most common fastners used in assembly?[2]ii. Which joining process could be suitable for joining rubbersheet material?[2](0)i. Give three reasons why mechanical fastners must be kept to aminimum for the assembly process.[37What are the three things recommended to lower theassembly costs?[3]

QUESTION 5A. i. The diagram illustrates the spin welding process, which is a friction welding…

Answered: (c) Elaborate the principles of vacuum…

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter13: Materials Processing

Section: Chapter Questions

Problem 10ETSQ

See similar textbooks

Similar questions

6. a) Welding has two main categories, discuss them in details b. Define and Distinguish these terms i welding ii. Soldering iii. Brazing ( c) What is Iron Montgomery. (
Q2) Fill the blank with suitable word or words: 1) The main types of cast iron are....... ... and ...... 2) There are three main reactions in Iron-Carbon phase diagram, theses are.... are the main stages of annealing heat treatment process. 3) ****** ***** ****** and ****** ....... and
(a) In general, which provides better fire performance, carbonate or silicate aggregates? Why? (b) Why does fire design incorporate a load reduction factor (Dfire) = 1.0? (c) Two identical beams (Beam 1 is simply supported, and Beam 2 is fully restrained) are heated under similar conditions. What does the mechanical strain equal to in each of these beams? (d) A design office located in Clemson, SC (with a branch in San Francisco, CA) envisions designing a new composite member made of steel and timber. This to-be designed member is expected to be used in wildfire-prone regions primarily for single family homes. Comment on how you would design such a member to achieve superior fire performance. (e) Plot and discuss the expected degradation faces in three bending elements (say, beams) to be made from concrete, steel and timber?
Q5 Show by free hand sketch only for 5 of the following 1- The phase diagram for 2 metals completely soluble in solid and liquid state. 2- The effect of process annealing on the properties of cold worked metals. 3- The effect of carbon percent on the mechanical properties of hypo and hyper steel. 4- Die drawing of round rod. 5- T.T.T diagram. 6- Cluster mill process.
Pick the correct statement regarding welding. O a. More Noise during welding O b. Welding process is slower O c. 100 % efficiency can be achieved in welding connection O d. Holes are drilled in welding connection
Hardness 6.54 (a) A 10-mm-diameter Brinell hardness indenter O produced an indentation 2.50 mm in diameter in a steel alloy when a load of 1000 kg was used. Compute the HB of this material. (b) What will be the diameter of an indentation to yield a hardness of 300 HB when a 500-kg load is used?
This board product in the picture is most likely made with ... a. dry process O b. blowline process soft process O d. multi-daylight pressing O c. e. wet process
Choose the correct answer of the following: tools are made by casting in graphite molds and then grinding to final size. 1. a) Cast-cobalt alloys. b) Diamond. c) Ceramics. d) Cermet. 2. For machining of carbide material, which of the following tool will be preferred? (a) Zero rake angle. (b) Positive rake angle. c) Negative rake angle (d) Small point angle. 3. When increasing the value of clearance angle, the strength of tool a) Increases. b) Decreases. c) Remains constant. d) Is unpredictable. 4. Angle between the face of the tool and a line parallel to the base of the tool is known as: a) Rake angle. b) Cutting edge angle. c) Clearance angle. d) Nose angle. 5. In grinding operation, grit sizes produce poor finishes. a) Small. b) Large. c) Medium. d) All of the Mentioned.
STEEL ANALYSIS full solution and final answer to 4 decimal places pls
The volume and mass are changed with Both options are above Forming process. O Cutting process.
Determine the welding zone classification of A36/A36M and A922/A922M steel.
For carbon steel casting with step pattern shown in Figure 1, that all surfaces will be machined after casting process, considering fraction coefficient to be 0.4 and density .to be 7.8 g/cm3 and Gating ratio to be 1.4: 1.2: 1 .Calculate for 4 pieces in one mold. Determine and draw a) pattern design b) Riser design c) Gating design 150mm 150mm 40 mm 130 mm 40 mm 500 mm

SEE MORE QUESTIONS

Recommended textbooks for you

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Solid Waste Engineering

Civil Engineering

ISBN:

9781305635203

Author:

Worrell, William A.

Publisher:

Cengage Learning,

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Solid Waste Engineering

Civil Engineering

ISBN:

9781305635203

Author:

Worrell, William A.

Publisher:

Cengage Learning,

SEE MORE TEXTBOOKS