Bde Diagan22510"Frequency ade)Figure Q.8(a)b) Continued overleaf.Dynamics & Control 3- May 2010OVERb) Figure Q.8(b) shows the block diagram representation of a system with input y(1) andresponse x(f). Derive an expression for the steady state response, x(t)„, of the systemwhen the input takes the form:y(1) - 10sin 51Y(s)X(s)s+5s+2Figure Q.8(b)

8(b) Given block diagram shown with input y(t)=10sin5t

b) Figure Q.S(b) shows the block diagram representation of a system with input y() and response x(f). Derive an expression for the steady state response, x(1),. of the system when the input takes the form: y(1) - 10sin St YIS) Xis) S+ 2

b) Figure Q.S(b) shows the block diagram representation of a system with input y() and response x(f). Derive an expression for the steady state response, x(1),. of the system when the input takes the form: y(1) - 10sin St YIS) Xis) S+ 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1) Suppose you have a sinusoidal input signal and wish at the output the signal should be same (in phase) as input signal but amplified then which circuit should you use? & WHY?? Draw the circuit diagram you would use.
(d) Consider the circuit composed of a series R-L branch in parallel with capacitance and the following are parameters: R=0.50, X₁ = 0.80 and Be=0.6 siemens.. V=20020° V. Calculate: the and the (i) the input current frontiers of knowsun (ii) and the active, reactive, and apparent power into the circuit.
A step-down chopper is to be used to supply power from a 600-V overhead wire to the commutator motor on a trolley bus. The motor may be mod- eled as a generated direct voltage in series with a resistance of 0.2 and an inductance of 25 mH. The frequency of the chopper is set at 500 Hz. (a) When the bus is stopped, what should be the ON time of the chopper to provide a motor current of 150 A? (b) What is the maximum possible generated voltage of the motor for which a current of 150 A can be supplied? (c) What is the average value of the supply current for the conditions of (a) and (b)? បទៅនឹងរស់របស (d) If the motor current is to be continuous, what should be its minimum. value?
What are two real-world consequences of having to amplify the input to a system so that the output reaches a desired steady-state value? Related to Electroncis & Circuits
A switching function q(t) is applied a semiconductor switch (MOSFET) which is controlling the power to a pure inductive load of 0.005H from 24V DC source. There is no previously stored energy in the inductor at t=0. Assuming the ideal components: a. Explain the operation of the circuit b. Find the switching period and frequency c. Calculate the mean (average) and RMS values of load voltage (vo) d. Find the load current expression and sketch it for first two switching periods e. Calculate the energy stored in the load inductor at the end of the second period from starting. L=0.05H 24v Vo: load voltage 1o: load current →t(ms) 4 2 3
c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/3. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state : iii. Determine the primary inductance.
c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/3. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state : V. Find the peak and mean of the switch current.
2) With reference to the waveform illustrated as below, design and develop a circuit which can obtain the output waveform as given below.After developing the appropriate circuit formulate the equation for average value and rms value of output voltage and output current m wt -V, m m wt
Consider the given system with input R(s) and output C(s) as shown in figure. • Calculate the natural frequency of oscillations, damping ratio, peak time, rise time, settling time, percentage overshoot and damped frequency of oscillations. • Also find the (time domain) expression for unit step response and Plot. Note: x=3
The unit of the attenuation constant is: Select one: a. A/m b. A/sec c. V/sec d. Np/m e. rad/sec f. rad/m g. Np/sec h. V/m
Consider the following step up converter with a resistive load of value RS ohms. it is supplied by a DC power source of magnitude Vs-200 V. The switching frequency is5 kHz and the duty cycle k is first set to 05 and the inductance used within the circuit has a value of L-10 mH. The switch is supposed to be ideal. if the average supply current is BOA then the average load current is: Select one: O a. la 80A O b. la 40A O cla 50 A O d. la 81 A
Evaluate the steady-state error component due to a step disturbance for the system Dis) 1000