Atwood's machine: Figure 1.4 is a sketch of Atwood's machine. It consists of masses m¡ and m2 suspended by a massless inextensible string over a frictionless, massless pulley. Evaluate the Lagrangian and obtain the equation of motion.? V= 0 X2 = 1 – x, m2 m,

Atwood's machine: Figure 1.4 is a sketch of Atwood's machine. It consists of masses m¡ and m2 suspended by a massless inextensible string over a frictionless, massless pulley. Evaluate the Lagrangian and obtain the equation of motion.? V= 0 X2 = 1 – x, m2 m,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Four equal, uniform rods of mass m and length 2a are hinged together to form a rhombus ABCD. The point A is fixed, while C lies directly beneath it and is free to slide up and down. The whole system can rotate around the vertical. Let 0 be the angle that AB makes with the vertical, and o be the angular velocity around the vertical, as shown in figure 3. Find the Lagrangian for this system and show that there are two conserved constants of motion. B Figure 3: The rotating rhombus.
Answer the following problem and write your complete solution and graph. 1. Write the equation of motion for the system given in the figure for the case that F(t) = F cos wt and the surface is friction free. Does the angle affect the magnitude of oscillation? Diagram: wwwm mass F(0) Fig. 4.4 Mass tied on the spring and Dashpot
* F2 # 3 E Problem 4. EOM Derivation Derive the equation of motion for the following system: We want to measure the spin rate w of the rotating shaft of a turbine. To do it we push a small mass m against the end of the shaft. The shaft makes friction contact with the drag cup mounted on the mass. The frictional torque is b (w). Assume that the rotational spring torque is ke and that the moment of inertia of mass m is J. J Rotating Shaft F3 @ $ 4 R b J, m Drag Cup F4 Q Search % 5 F5 T 0 Wall * A 6 F6 Y 2 * F7 & 7 PrtScn U F8 4 8 Home 6. F9 9 End F10 Po 0
A car is modeled as shown in Figure. Derive the equations of motion and find matrix M, C, and K. Mass = M, mass moment of inertia = JG .000 m1 k₂ F1 1 k2 000 k₁ k₁ m2 F2, X2 ell
Figure shows a mechanical system. The connecting link has moment of inertia J about its pivot point, and rotation angle is positive clockwise. Position of mass m is positive to the right. Both the angular and translational displacements are measured from the equilibrium position where all springs are undeflected. Derive the mathematical model of this system assuming small rotation angle 8. Link, moment. of inertia J L k₁ www m O k₂ www
TORSIONAL SYSTEM Q-4 For the system in fig (4) find : 1. F.B.D 2. Equation of motion & wd. 3. e(t), for 3 < 1. 4. 8.
A uniform disk of mass 2M and radius a can roll along a rough horizontal rail. A particleof mass m/2 is suspended from the centre C of the disk by a light inextensible string oflength b. The whole system moves in the vertical plane through the rail. Take as generalisedcoordinates x, and θ the angle between the string and the downward vertical.(a) Write the Lagrangian for the system.(b) Obtain Euler-Lagrange equations.(c) Identify the cyclic coordinate and find the corresponding conserved momentum (say px).(d) Is px the horizontal linear momentum of the system?
For the problem related to Fundamental.4, a sketch of the considered system showing and naming (or numbering) every part of the system considered, the respective velocity and acceleration of each, and the frame of reference considered is mandatory. Its absence will automatically make the problem false. Gear A on the drive shaft of the outboard motor has a radius rA=3 in. and the meshed pinion gear B on the propeller shaft has a radius rB=64 in. The point P is located on the propeller's tip at a distance 7 in. from the neutral axis of the propeller's shaft. P B At the beginning of the propulsion, the drive shaft rotates with an angular acceleration a = A. t2.2 rad.s2 where t is in seconds. what must be the value of A to have, while starting from rest, vp=21 in.s1 in 5 seconds ?
Question 9: Figure 3 shows a mechanical system. The rod (with moment of inertia J) rotates about the pivot at only small rotation angles. As pictured, theta is positive clockwise. Attached is mass m, which moves positive to the right. When stationary in the position shown, all springs are undeflected. Using BOBODDY, find the mathematical model of this system assuming small rotation angle 0. Link, moment of inertia J k3 L₁ 12 5 Ꮎ wwww Figure 3: Mechanical System m k₂ b
0.5 m, k = 500 N/m, and k = 40 N.m/rad, In the system shown, m = 10 kg, r = 0.3 m, Ko where ko is the radius of gyration of the pulley about point 0. There is no slippage between the cord and the pulley. Replace the system with an equivalent { a) torsional spring and mass moment of inertia at point 0, and b) translational mass and spring at point A. т, Ко kt А k m ww
For the problem related to Fundamental.4, a sketch of the considered system showing and naming (or numbering) every part of the system considered, the respective velocity and acceleration of each, and the frame of reference considered is mandatory. Its absence will automatically make the problem false. Gear A on the drive shaft of the outboard motor has a radius rÃ=8 in. and the meshed pinion gear B on the propeller shaft has a radius r=50 in. The point P is located on the propeller's tip at a distance 10 in. from the neutral axis of the propeller's shaft. B At the beginning of the propulsion, the drive shaft rotates with an angular acceleration a = what must be the value of A to have, while starting from rest, vp=28 in.s¹ in 8 seconds ? A. t2.3 rad.s2 where t is in seconds.
For the rotational mechanical system below, write, but do not solve, the equations of motion. T 大 Ji cele DI