An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most signi cant bits are used as a network ID, and the 16 least signi cant bits are used as a host ID. However, the host ID cannot be all 0's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network?

An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most signi cant bits are used as a network ID, and the 16 least signi cant bits are used as a host ID. However, the host ID cannot be all 0's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network?

Operations Research : Applications and Algorithms

4th Edition

ISBN:9780534380588

Author:Wayne L. Winston

Publisher:Wayne L. Winston

Chapter20: Queuing Theory

Section20.10: Exponential Queues In Series And Open Queuing Networks

Problem 8P

See similar textbooks

Similar questions

An IP address can be written as a 32-bit number. For a class B network, the two most significant bits are set to 10. The 16 most significant bits are used as a network ID, and the 16 least significant bits are used as a host ID. However, the host ID cannot be all 0's or all 1's. How many hosts (i.e., host IDs) can there be on a class B network?
Registration Number: 193046 Consider a network with 3 hosts and a NAT router. Suppose that the network address of the home network is 192.168.NNN/24, where NNN are the last 3 digits of your Reg#. For example, if your Reg# is BSE193046, NNN = 046 and therefore the network address wil be 192168.46/24. (If NNN>255, consider NNN=254) (a) Assign any public IP address to NAT router’s outgoing interface. (b) Assign IP addresses to all 3 hosts and local interface of the NAT router in the home network. (
Which of the following instructions falls in the category of data transfer instructions? JUMP LOAD ROTATE AND
Skype is a well‑known VoIP system used not only for peer‑to‑peer conversations but also for audio and video conferencing involving three or more callers. Assume a video conference with a central server on Skype has N callers, and each caller generates a constant data stream at rate r bps. How many bits per second does the call initiator need to send? How many bits does each of other N‑1 callers need to send?
• IPV6 addresses use 128 bits to represent an address which includes bits to be used for subnetting. The second half of the address (least significant 64 bits) is always used for hosts only. Therefore, there is no compromise if we subnet the network. Use the Figure below to Create five subnets using route prefix 2001:db:acad::/48 (1 Marks) Routing Prefix Subnet ID Interface ID 48 Bits 16 Bits 64 Bits
TCP / IP uses the client-server communication model, in which a user or computer (a client) receives a service (such as sending a web page) from another computer (a server) on the network. In short, the TCP / IP protocol suite is classified as stateless, which means that each client request is considered new because it has nothing to do with previous requests. Being stateless, network routes are released so that they can be used continuously. Answer the following questions briefly. How does resource reservation work in the TCP / IP model? Which TCP / IP layer is responsible to reserve resources across a network using the TCP / IP model? What protocol assigns an IP address to the client connected to the Internet? Checksum is used by various protocols on the Internet, but not at the one of TCP / IP Explain.
Assume that there is a shared connection (for example, an Ethernet bus) with a speed of 1 Mbps. How much time (in microseconds) is required to send a frame with a length of 1000 bits over this link?
TCP session sends 50 packets per second over an Ethernet Local Area Network (LAN). Each packet consists 2280B (excluding the preamble and cyclic redundancy check (CRC)). Calculate the size of the headers, and hence the TCP payload data. What therefore is the TCP throughput of the session?
NAT translation table LAN side addr WAN side addr 135.122.200.215 10.0.1.15 10,0.1.13 address 135.122.200.215 S: 10,0,1.27 2 D: 1 D: S: S: D: S: 10,0.1.15 D: 135.122,200,215 10.०.1.22
A packet switch receives a packet and determines the outbound link to which the packet should be forwarded. When the packet arrives, one other packet is halfway done being transmitted on this outbound link and four other packets are waiting to be transmitted. Packets are transmitted in order of arrival. Suppose all packets are 1,500 bytes and the link rate is 2 Mbps. What is the queuing delay for the packet? More generally, what is the queuing delay when all packets have length L, the transmission rate is R, x bits of the currently-being-transmitted packet have been transmitted, and n packets are already in the queue?
SUBNET ADDRESSING Consider the router and the two attached subnets below (A and B). The number of hosts is also shown below. The subnets share the 23 high-order bits of the address space: 144.145.110.0/23 : A 175 hosts QUESTION 2 OF 10 Answer How many hosts can there be in this address space? 144.145.110.0/23 B Assign subnet addresses to each of the subnets (A and B) so that the amount of address space assigned is minimal, and at the same time leaving the largest possible contiguous address space available for assignment if a new subnet were to be added. Then answer the questions below. 84 hosts
The Transmission Control Protocol (TCP) is one of the core protocols of the Internet protocol suite (IP), and is so common that the entire suite is often called TCP/IP. A TCP connection is managed by an operating system through a programming interface that represents the local end-point for communications, the Internet socket. During the lifetime of a TCP connection the local end-point undergoes a series of state changes. These states are: (1) TCPEstablished: connection is on and ready for data transfer, (2) TCPCLosed, connection is off, and (3)TCPListen, TCP is listening for connection requests. The TCP Connection performs three operations, where the behavior of the operations changes as the state of the connection changes. These operations are: (1) open, (2) close, and (3) Acknowledge. What design pattern best suites your needs? 1. Chain of responsibility 2. Strategy 3. Command 4. State