A uniform 10-kg bar OA is suspended from the pin at O. The bar is at rest when the 1.5 kg bal B with negligible diameter hits end A with a velocity of VB1-30 m/s. After the impact, the ball bounces off following the direction shown. 0 A VB2 1. What is the angular velocity of rod OA just after impact? 2. What is the coefficient of restitution between ball B and rod OA? B VB1 24 1.8 m

A uniform 10-kg bar OA is suspended from the pin at O. The bar is at rest when the 1.5 kg bal B with negligible diameter hits end A with a velocity of VB1-30 m/s. After the impact, the ball bounces off following the direction shown. 0 A VB2 1. What is the angular velocity of rod OA just after impact? 2. What is the coefficient of restitution between ball B and rod OA? B VB1 24 1.8 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 4 kg ball is thrown at the suspended 0.35 kN block with a velocity of 5 m/s. If the impact is perfectly elastic, what is the value of height "h" to which the block will swing before it comes to rest? 5 m/s B. A
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the %3D figure. Determine the total resultant force acting on the gate and the location of the center of pressure. 6 ft 3ft VAVAVAVAVA Ib f Unit weight of the liquid (y) Value of hbar (h) Arca of the rectangular gate (A) Hydrostatic Force (F) Vahe of (Igx) Vahue of ybar (9) Location of the Hydro. Force measured from the water surface of the gate inclined (yel Ib ft ***answer Hydrostatic Force Fon the box below: Answer: 1311.03 The correct answer is: 1022.1
Q5 A structural member of an engineering hoist has length of 1m and the cross-section as shown in Figure Q5. For the member calculate: a) the moment for purely elastic bending, b) the moment for partial plastic bending, whereby the plastically deformed region should not exceed 15mm in vertical direction from either side. Take a, = 250MNM-2 and E = 210GNM-2. 70 60 Figure Q5 09
A crate with a given weight of 50kg translates on the surface shown at velocity of 7mn/s at t-0. u - 0.40. How long will it take for the crate to stop moving? How far would it have travelled? %3D Vo37 m/s 50 kg HE =0.40 O t-1.24s; x=D3.19m O t-2.14s; x=8.40m O t=1.784s; x-6.24m O t-1.884s; x=3.14m O t-2.08s; x= 2.91m O t-1.0245; x-2.19m
For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple of that same magnitude M were applied in a counterclockwise direction, what would be the value of Ax? -2.3 2.3 P 220 lb Answers: M- Ax i 1.8' 64 lb-ft lb .8'
A cantilever beam with length L carries a concentrated load of P at its free end. The beam is tapered with diameters of D at the support and d at the free end. The beam is to be analyzed considering flexure only. Which of the following expressions gives the distance from the free end where the beam will break? Select the correct response: Ld/[2(D-d)] Ld/[2(D+d)] LD/[2(D+d)] LD/[2(D-d)]
اقرا السؤال وحمل الاجابة بالاسفل From the figure below: 1) Determine the moment about point A? 2) Determine the resultant force? F2= 110kN F1=70KN r =6m 32 4 8m 3 F3=200kN A 17m-
Answer Q1. A. Inside a 60-mm diameter cylinder a piston of 59 mm diameter rotates concentrically. Both the cylinder and piston are 80 mm long, as shown in Fig.If the space between the cylinder and piston is filled with oil of viscosity of 0.3 Ns/m² and a torque of 1.5 Nm is applied, find the rpm of the piston. dy 0.0005 mm I 80 mm 59 mm D-60 mm Piston Cylinder
Two concrete blocks weighing 1423 N each form part of the retaining wall of a swimming pool. Will the blocks be in equilibrium when the pool is filled and the water exerts the line loading shown? Figure P 7.38 -254 mm 457 mm 4y = 0,5 Plastic liner 457 mm H=L0- 5604 N/m
A 450-g tetherball A is moving along a horizontal circular path at a constant speed of 4 m/s. (A) Determine the angle theta in degrees that the cord forms with pole BC, (B) determine the tension in the cord in Newton
Question In a Porter governor, each of the four arms is 400 mm long. The upper arms are pivoted on the axis of 400 the sleeve whereas the lower arms are attached to the 1 sleeve at distance of 45 mm from the axis of A. rotation. Each ball has a mass of 8 kg and the load on the sleeve is 60 kg. What will be the equilibrium speeds for the two extreme radii of 250 mm and 300 400 mg mm of rotation of the governor balls? 45 i B 60/2 kg
Fig. shows a bar LMNP fixed at L and P is subjected to axial force. Find the force in each portion of the bar and the displacement of points M and N. Take E =200 GN/m². R₁4 1000 mm² LMJ 1500 mm N 100 KN 2 0.5 m 0.75 m 2000 men 31 m P R₂