A type of noise that is directly proportional to the frequency of the operation. a. shot noise b. transit time noise C. solar noise d. thermal noise
Q: Another name for comparator is O process O controller O error detector O actuator
A: Comparator: It has two analog input terminals and and one binary digital output . It is a device…
Q: Control Logic controllers are based on 16 digit operations. True or False
A: Programmable logic controllers are based on 16 bits or 32 bits. We generally used logic controllers…
Q: One of the following is the example for process control system. a. Water level controller b. Radar…
A: Cement Industry is an example of process control system.Advanced process control is used in cement…
Q: Explain the registers and their working in detail.
A: A register is a temporary storage area built into a CPU. Some registers are used internally and…
Q: Identify the process happen in Figure Q29(a). Interrupt User Program Handler X Interrupt Handler Y
A: The process shown in fig. is defined as the bending waves around the corners of an obstacle or…
Q: For the given details, Clockrate = 900 MHz, Instructions executed = 1200, Machine instruction = 30…
A:
Q: Write an instruction sequence to set bits 7, 6, 1 & 0 in Accumulator A and clear the other four bits…
A: According to the question, we need to write the instruction sequence to set the bits 7,6,1, and 0…
Q: Which of the following converts physical variables into electrical signals? O A) Actuator B)…
A:
Q: Assuming a stable system. What type is the system? Assuming that the amplitude of the input is…
A: In this question, We need to check the type of the system? In the second part, Assuming that the…
Q: Program initiated operations are controlled using lines. a Output control O B. Address bus c Data…
A: The output control is activated or generated in the response of the program-initiated operations. An…
Q: a) Describe the main sources of errors in a measurement process and state how they may be avoided or…
A: The main sources of error are: The sources of random errors are slight fluctuations in an…
Q: Describe how the relay controls the motor.
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: '8085 Q1: B: Classify instruction according to the addressing modes
A: In this we will write about addressing modes in 8085 processor....
Q: Match the following terms. Flag A. contains temporary information Register B. contains status…
A:
Q: A shift register analogy would be to compare the magnetic disks and drums to recirculating shift…
A: Shift registers operation is similar to magnetic disks and drums in manner of reading data in same…
Q: A person is recording measurements from an analog data reader. During the first reading, he was not…
A: Since we are allowed to solve only up to first three parts of a question the below answer contains…
Q: A binary code to represent the decimal digits [0-9] must contain at least four bits because 3digits…
A: The decimal number has a range of 0 to 9 and it can be represented by 4 bits.
Q: What two principle functions are performed by a shift register
A: The Shift Register is one of the sequential logic circuits that can be popularly used for the…
Q: Q4: What are the relevant datapath lines and what are the values of each of the control lines for…
A: According to the question, we need to explain the following instructions A) add $rd, $rs, $rt B)…
Q: Q2: What is the maximum clock frequency that the control that can used? If time delay is 30 ns to…
A: Given time delay=30 nstransfer address=20 nsaddress register=20 ns
Q: Q4) List the flags that would be affected during the use of IN instruction.
A:
Q: Mechatronics 37.
A: We need to find out the output for given logic diagram
Q: Q1 D1 Do CLK-
A:
Q: Which one of the following is used to transform an electrical signal into physical output? a.…
A: The explanation is as follows.
Q: Introduction explaining the importance of the measurement process
A: Importance of measurement process in electrical and electronics systems is shown below using…
Q: Static VAR control
A: A static VAR compensator is a parallel combination of a controlled reactor and fixed shunt capacitor…
Q: Which of the following operation instruction interrupts the program scan when it is executed: Select…
A: The MOV are used for data moving so, option A is wrong. If the input device is OFF or open, then the…
Q: Answer the following questions (a) What is a clock signal? (b) Differentiate between positive going…
A:
Q: (a) Is this a Mealy machine or Moore machine? (b) Fill in the outputs on the transition table. (c)…
A:
Q: This error signal is given to the control element, to keep the output of the system in an undesired…
A: Error signal is the difference of input signal and feedback signal from output.
Q: What are the types of Time division multiplexing? Explain each type
A:
Q: What is the role of the @ operator and a sensitivity list in an always statement?
A: Sensitivity List: The sensitivity list will have the list of signals for which the always statement…
Q: is a type of control system in which the process output is controlled at the setpoint level. a.…
A: Control system A control system is a system which can provides the desired response to the system…
Q: Using Table 16.1 , identify the components of the logic system shown in the figure.
A: The given circuit is shown below: Component 1 is the two inputs AND Gate. Component 2 is the NOT…
Q: A system bus can be used to carry the control signals Select one: O True O False
A: The above question is related to subject of microprocessor There are 3 systems bus that can be…
Q: The control signal from the controller does not reduce the error. Select one: True False
A: We need to tell about the controller.
Q: 2- When the BIU is free to read next instruction code?
A: The bus interface unit provide the interface between the external memory unit and the input output…
Q: What is the purpose of clock pulses?
A: Clock pulse: Clock pulse is a timing signal used to synchronize the activities performed by digital…
Q: 1. What is the difference between accuracy and precision? 2. List four sources of poss.ble errors in…
A: “Since you have asked multiple question, we will solve the first question for you. If you want any…
Q: 20)What is the velocity error constant K, of the compensated system? V
A:
Q: 7-segment display,
A: 7-Segment LED Display Decoder Circuit. Using a decoder circuit we can decode binary or binary-coded…
Q: Describe, how are they different and how are they similar between Sensor and Actuator.
A: Actuator is a device which converts electrical signals to physical properties(characteristics). The…
Q: Q.Explain sources of noise and its type(electrical amd static noise) in detail?Explain magnetic…
A:
Q: Following error
A:
04
Step by step
Solved in 2 steps
- What is the action of a capacitor in a Power Supply Circuit?* a. To de-couple DC component of the rectified AC input b. To increase the DC component of the output wave. c. To remove DC component of the AC wave. d. None of the above.Explain the meaning and give a practical significance of the unit step signal and ramp signalA common objective when manufacturing printed circuit boards (PCBs) is O a. maximizing the number of drill bit changes. O b. maximizing the number of holes drilled. c. minimizing the total distance the drill bit must be moved. O d. minimizing the number of holes drilled.
- Test the accuracy of the equation by applying the operation in Ampere law (del.)? If there is a mistake, correct this mistake.13. Name two circuits that can be used to create clock generators in ASICs. b.Subject name: Signal processing measurement Question: Is there any difference between the metallic resistance and the semiconducting resistance?
- 4- Why do we need three RC network for phase shift oscillator? Can it be two or four ? and why?The resultant DC signal from a half-wave rectifier circuit was investigated, the following trace was observed on the oscilloscope: RIGOL T'D f 0 -80.0mV CH2 500MV Time 5.000ms T+0.0000s The trace has a slight ripple in its structure. This ripple can be attributed todesign a synchronous counter with sequence One, Four, Seven, one, ... Hint: the counter is idle if its input is low.
- In a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.6 V respectively. The form factor of this circuit is ___________________.please i need help quickly n 57 The ARDUINO IDE stands for. d a. Integrated development environment out of b. None of these O c. Integrated drive electronics O d. Instructional development environment 58 What does the following ARDUINO command do? analogWrite (9, 63) a. Sets the PWM duty cycle to 25% ut of b. Sets the PWM duty cycle to 75% c. Sets the PWM duty cycle to 50% d. Sets the PWM duty cycle to 30%Ripple counters are also called O a. VLSI counters O b. Asynchronous counters SSI counters O d. Synchronous counters Given in the figure is PLA circuit, used to imnlement the Pooloan fu